GEEKWORM NAS Family

Raspberry pi 5 NAS Storage

Raspberry pi 5 NVMe

Geekworm PCIe to NVME Sets:

After the release of the Raspberry Pi AI Kit, we tested four PIPs: X1001, X1004, X1011, and M901. X1001, X1004, and M901 all support the hailo-8 ai ​​accelerator, but X1011 does not.

It should be noted that X1004 uses ASMedia ASM1182e PCIe switch, and X1011 uses ASM1184e, they can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch, and speed is still PCIe Gen 2.0 5Gbps speed. when you use an hailo-8 ai accelerator, Raspberry Pi Fundation highly recommends using PCIe 3.0 to achieve best performance with your AI Kit.

Our tentative conclusions are as follows:

• If you need to use hailo-8 ai accelerator with high performance, it is recommended to use X1015/X1002/X1003/M901/ the official M.2 HAT+ etc. When choosing these PIP boards, you should focus on whether there is a conflict between the camera cable and the PIP board installation, and enable PCIe3.0 to use hailo-8 ai accelerator. At the same time, you need to prepare an SD card as the system disk.
• If you don't care about the high performance brought by PCIe 3.0, then you can consider using X1004, so that you can use any socket of X1004 to install NVME SSD as the system disk, and another socket to install hailo-8 ai accelerator, so as to have both.

Model	Compatible with	Position	NVMe M2 SSD Length Support	Matching Case	Matching Cooler	Support NVMe Boot	Support PCIe 3.0	Support Hailo-8 AI Accelerator
X1000	Raspberry Pi 5	Top	2230/2242	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Not tested
X1001	Raspberry Pi 5	Top	2230/2242/2260/2280	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Yes
X1002	Raspberry Pi 5	Bottom	2230/2242/2260/2280	P580 / P580-V2	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	NO
X1003	Raspberry Pi 5	Top	2230/2242	P579 / P425	Official Cooler / H501 Only	Yes	-	Not tested
X1004	Raspberry Pi 5	Top	Dual ssd: 2280	P579-V2	Official Cooler / Argon THRML Cooler / H505/H501	Yes (Requires EEPROM 2024/05/17 and later version)	NO	Yes
X1015	Raspberry Pi 5	Top	2230/2242/2260/2280	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Yes
X1005	Raspberry Pi 5	Bottom	Dual ssd: 2230/2242/2260/2280	P580-V2	Official Cooler / Argon THRML Cooler / H505/H501	Yes (Requires EEPROM 2024/05/17 and later version)	NO	Yes
X1011	Raspberry Pi 5	Bottom	4 ssds: 2230/2242/2260/2280	X1011-C1	Official Cooler / Argon THRML Cooler / H505/H501	Yes (eeprom 2024/05/17 and later version)	NO	NO
X1012	Raspberry Pi 5	Top	2230/2242/2260/2280	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Not tested
M901	Raspberry Pi 5	Top	2230/2242/2260/2280	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Yes
Q100	Raspberry Pi 5	Top	2242	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Not tested
Q200	Raspberry Pi 5	Top	Dual ssd: 2280	P579	Official Cooler / Argon THRML Cooler / H505/H501	NO	-	Not tested
M300	Raspberry Pi 5	Top	2230/2242	P579	Official Cooler / Argon THRML Cooler / H505/H501	Yes	-	Not tested
M400	Raspberry Pi 5	Top	2230/2242/2280	P579	Official Cooler/ Argon THRML Cooler / H505/H501	Yes	-	Not tested

Raspberry pi 5 SATA

Raspberry pi 5 SATA Series

Model	Description	Supported HDD/SSD	Mounting Position	Support NVMe Boot	Matching Case	Matching Cooler
X1100	USB to SATA	2.5" SATA HDD / SSD	Bottom	Yes	X1100-C1	Official Cooler / H505 Active Cooler / Argon THRML Cooler / H501
X1006	PCIe to SATA	2.5" SATA HDD + M.2 SATA Key-B 2280 SSD	Bottom	NO	NO Case yet	Official Cooler / H505 Active Cooler / Argon THRML Cooler / H501
X1007	PCIe to SATA	Dual SATA 2.5" HDD / SSD	Bottom	NO	NO Case yet	Official Cooler / H505 Active Cooler / Argon THRML Cooler / H501
X1008	PCIe to SATA	2.5" SATA HDD / SSD + 3.5" SATA HDD Shield	Bottom	NO	NO Case yet	Official Cooler / H505 Active Cooler / Argon THRML Cooler / H501
X1009	PCIe to SATA	5PCS 2.5" SATA HDD / SSD /3.5" SATA HDD	Top	NO	NO Case yet	Official Cooler / H505 Active Cooler / Argon THRML Cooler / H501

NASPi Storage series

Please enter the following correspond user manual and installation video page according to the NASPi product you purchased.

Model	Compatible with	Supported HDD	Installation Video
NASPi	Raspberry Pi 4B	2.5 inch HDD/SSD (1pcs)	Please refer to NASPi Installation Video
NASPi Lite	Raspberry Pi 4B	2.5 inch HDD/SSD (1pcs)	Please refer to NASPi Lite Installation Video
NASPi Gemini 2.5	Raspberry Pi 4B	2.5 inch HDD/SSD (2pcs)	Please refer to NASPi Gemini 2.5 Installation Video
NASPi Gemini 3.5	Raspberry Pi 4B	3.5 inch HDD/SSD (2pcs)	Please refer to NASPi Gemini 3.5 Installation Video
NASPi CM4-M2	Raspberry Pi CM4	M.2 SATA & M.2 NVMe(2pcs)	Please refer to NASPi CM4-M2 Installation Video
NASPi CM4-2.5	Raspberry Pi CM4	2.5" SATA3/SATA2/SATA (1pcs)	Please refer to NASPi CM4-2.5 Installation Video

Raspberry pi 4 NAS Storage

for 2.5" sata

Product Name	NASPi	NASPi Lite	NASPi Gemini 2.5 V2.0	X825 V2.0	X825 V1.5	X825v	X880	X883	X828(Stackable)	X829(Dual SATA)
Compatible with	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4/ 3B+/ 3B/ 2B/ B+	raspberry pi 4
Socket	2.5" sata HDD/SSD	2.5" sata HDD/SSD	2.5" sata HDD/SSD	2.5" sata HDD/SSD	2.5" sata HDD/SSD	2.5" sata HDD/SSD	2.5" /3.5" sata HDD/SSD	2.5" sata HDD/SSD	one or multiple 2.5" sata HDD/SSD by stack the X828	Dual 2.5" sata HDD/SSD
Number of SSD/HDD Supported	1 pcs	1 pcs	1 or 2 pcs	1 pcs	1 pcs	1 pcs	1 or 2 pcs	1 or 2 pcs	1+ pcs	2 pcs
Power Requirement	USB C 5Vdc +/-5% , ≥4A	USB C 5Vdc +/-5% , ≥4A	DC 6-18V +/-5% , ≥4A	DC 5V/≥4A -5.5x2.1mm jack USB C 5Vdc +/-5% , ≥4A	DC 5V/≥4A - 5.5x2.1mm jack USB C 5Vdc +/-5% , ≥4A	USB C 5Vdc +/-5% , ≥4A	12Vdc +/-5% , ≥3A - 5.5x2.1mm jack	DC 5V/≥4A - 5.5x2.1mm jack	DC 5V/≥4A - 5.5x2.5mm jack 1pc power supply for every 3pcs X828	DC 5V/≥4A - 5.5x2.5mm jack
Matching Case	Already with a NUC stylc case with a 4010 PWM fan	Already with a NUC style case with a 4010 ordinary fan	Already with a case with a 4010 PWM fan	Model: X825-C8 With a power switch button with a 4010 ordinary fan For Pi 4 + X825 V2.0 + X735	Model: X825-C6 With a power switch button with a 4010 ordinary fan For Pi 4 + X825 V1.5 + X735	Model: X825-C8 With a power switch button with a 4010 ordinary fan For Pi 4 + X825v + X735	Model: X880-C1 with a 4010 ordinary fan	No matching case	Model: [X828-C1] With a power switch button with a 4010 ordinary fan	Model: X829-C1 With a power switch button with a 6010 ordinary fan
Extra Cooling Solution Recommended	/	/	/	X735	X735	X735	Horizontal ICE Tower Fan	X735/X708	X735	X735/X708
Installation Video	NASPi V1.3: Click to play NASPi V1.5: Click to play	Click to play	Click to play	Click to play	Click to play	Click to play	Click to play	/	Click to play	X829 + X735: Click to play X829 + X708: Click to play
Differences	NASPi & NASPi Lite are both NUC-style aluminum case, supporting 1 SSD/HDD; NASPi Gemini is a metal case, supporting 1 or 2pcs SSDs/HDDs working at the same time, NASPi Gemini support RAID NASPi & NASPi Gemini support 2 micro HDMI sockets; NASPi Lite support 1 full size HDMI socket; NASPi and NASPi Gemini support Safe Shutdown, PWM Fan; NASPi Lite does not support Sfe Shutdown and PWM Fan			Functions of X825 V2.0 & X825 V1.5 & X825v are the same X825 V2.0 is updated from X825 V1.5，add 4 test pins to achieve which implified power supply and installation X825v powered via raspberry pi or X735, not from the on-board DC socket of X825v; X825 V1.5 & X825 V2.0 powered via raspberry pi or X735 or on-board DC socket			Both X880 & X883 support 1 or 2pcs SSD/HDD working at the same time X880 supports 2.5 inch and 3.5 inch；X883 only supports 2.5 inch X880 require 12V PSU, while X883 require 5V PSU X883 is more compact than X880, SSD/HDD can be directly inserted on both sides of the X883 board, while the X880 needs two other boards to carry the SSD/HDD.		off-production

for 3.5" sata

Product Name	X832 V1.0	X832 V1.2	X880	NASPi Gemini 3.5	X885	X835 (stackable)
Compatible with	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4	raspberry pi 4/ 3B+/ 3B/ 2B/ B+
Socket	3.5" sata HDD	3.5" sata HDD	2.5" /3.5" sata HDD/SSD	Dual 3.5" sata HDD	Dual 3.5" sata HDD	one or multiple 3.5" HDD by stack the X835
Number of SSD/HDD Supported	1 pcs	1 pcs	2 pcs	2 pcs	2 pcs	1+ pcs
Power Requirement	12Vdc +/-5% , ≥3A - 5.5x2.1mm jack Power via X832 DC 12V In socket	12Vdc +/-5% , ≥3A - 5.5x2.1mm jack Power via X832 DC 12V In socket	12Vdc +/-5% , ≥3A - 5.5x2.1mm jack	12Vdc +/-5% , ≥3A - 5.5x2.1mm jack	12Vdc +/-5% , ≥5A - 5.5x2.1mm jack	12Vdc +/-5% , ≥3A - 5.5x2.5mm jack Power via X835 DC 12V In socket
Matching Case	Model: X835-C1 With a power switch button with a 4010 ordinary fan For Pi 4 + X832 V1.0 + X735	Model: X832-C1 With a power switch button with a 4010 ordinary fan For Pi 4 + X832 V1.2 + X735	Model: X880-C1 with a 4010 ordinary fan	Already with a case with a 4010 PWM fan	Refer to NASPi Gemini 3.5 for the kit of X885 with Case and PWM Fan	Model: X835-C1 With a power switch button with a 4010 ordinary fan This case is only compatible with 1pc X835, not compatible with 2 or more X835
Extra Cooling Solution Recommended	X735	X735	Horizontal ICE Tower Fan	/	/	X735
Installation Video	/	Click to play	Click to play	https://youtu.be/iifa9cTGqFM	/	Click to play
Differences	X832 V1.0 and X832 V2.0 only support one HDD. X880 / X885 / NASPi Gemini 3.5 supports 1 or 2 HDDs to be used at the same time; X835 supports stacking to use one or multiple HDDs at the same time; X832 V2.0 updated from V1.0, adding 4 test pins, which simplifies power supply and installation, and the DC jack is also changed from 5525 to 5521 X885 is the single board, NASPi Gemini 3.5 is composed of X885 single board + Case + 4010 3Pin PWM fan; X835 compatible with raspberry pi 4/ 3B+/ 3B/ 2B/ B+, X832 V1.0 / X832 V1.2 / X880/X885/NASPi Gemini 3.5 only compatible with raspberry pi 4

for M.2 NVMe, M.2 SATA, mSATA

Raspberry Pi 4 M.2 NVMe, M.2 SATA, mSATA Shield:

Product Name	Compatible with	Socket	Power Requirement	Matching Case	Extra Cooling Solution Recommended	Installation Video
X862 V2.0	Raspberry Pi 4	M.2 SATA Key-B NGFF SSD 2280	USB C 5Vdc +/-5% , ≥4A	X857-C3	X735/X708	Click to play
X863	Raspberry Pi 4	M.2 SATA Key-B NGFF SSD 2280	USB C 5Vdc +/-5% , ≥4A	X863-C1	X732	Click to play
X876	Raspberry Pi 4	M.2 NVMe Key-M 2280	USB C 5Vdc +/-5% , ≥4A	X863-C1	X732	Click to play
X873 V2.0	Raspberry Pi 4	M.2 NVMe Key-M 2280	USB C 5Vdc +/-5% , ≥4A	NO Matching Case yet	-	-
X872 V2.0	Raspberry Pi 4	M.2 NVMe Key-M 2280	USB C 5Vdc +/-5% , ≥4A	X857-C3	X735/X708	-
X857 V2.0	Raspberry Pi 4	mSATA SSD	USB C 5Vdc +/-5% , ≥4A	X857-C3	X735/X708	Click to play

Raspberry pi 3 NAS Storage

Raspberry pi 3 NAS Storage Family

Item	2.5" SATA SSD/HDD			3.5" SATA HDD	mSATA SSD		NVMe M.2 SSD	NGFF M.2 SSD
Product Name	X820	X821	X822(Dual SATA)	X830	X850	X852(Dual mSATA)	X870	X860	X851
Compatible with	raspberry pi 3B+/ 3B/ 2B/ B+/ ROCK64/ Thinker Board	raspberry pi 3B+/ 3B	raspberry pi 3B+/ 3B/ 2B/ B+/ ROCK64/ Thinker Board	raspberry pi 3B+/ 3B/ 2B/ B+/ ROCK64/ Thinker Board	raspberry pi 3B+/ 3B/ 2B/ B+	raspberry pi 3B+/ 3B/ 2B/ B+	raspberry pi 3B+/ 3B/ 2B/ B+	raspberry pi 3B+/ 3B/ 2B/ B+	raspberry pi 3B+/ 3B
Interface/Socket	2.5" sata HDD/SSD	2.5" sata HDD/SSD	Dual 2.5" sata HDD/SSD	3.5" sata HDD	mSATA SSD	Dual mSATA SSD	M.2 NVMe SSD 2280, 2260, 2242, 2230	M.2 NGFF 2280/2260/2242/2230	M.2 NGFF 2280
Power Requirement	DC 5V/≥4A - 5.5x2.1mm jack	USB C 5Vdc +/-5% , ≥4A	DC 5V/≥4A - 5.5x2.5mm jack	DC 12V/≥3A - 5.5x2.5mm jack	Powered via Pi's USB port	DC 5V/≥4A - 5.5x2.5mm jack	Powered via Pi's USB port	Powered via Pi's USB port	Powered via Pi's USB port
Matching Case	Model: X820 Case For X820 + X735+pi 3B+/ 3B/ 2B/ B+/ ROCK64 With Power Switch With Cooling Fan	No Matching Case	Model: X830 Case For X830 + pi 3B+/ 3B/ 2B/ B+/ ROCK64 With Power Switch With Cooling Fan	-	No Matching Case	-	-	-
PCB Size	10.7 x 8.5 cm	10.7 x 8.5 cm	16.5 x 10.8 cm	15.5x11.8 cm	8.5 x 5.6 cm	9.9 x 8.6 cm	8.5 x 5.6 cm	8.5 x 5.6 cm	82x87mm/3.22x3.42inch
Installation Video	Click to play	-	-	-	-	-	-	-	-

Nvidia Jetson Nano Storage

Nvidia Jetson Nano Storage Family

Item	2.5" SATA SSD/HDD	mSATA SSD	NVMe M.2 SSD	M.2 NGFF SSD
Product Name	T300	T130	T100	T150
Compatible with	Nvidia Jetson Nano A02/ B01	Nvidia Jetson Nano A02/ B01	Nvidia Jetson Nano A02/ B01	Nvidia Jetson Nano A02/ B01
Interface/Socket	2.5" sata HDD/SSD	mSATA SSD	M.2 NVMe SSD 2280, 2260, 2242, 2230	M.2 NVMe SSD 2280, 2260, 2242, 2230 (Only only 2280 holes are already threaded.)
Power Requirement	DC 5V/≥4A - 5.5x2.1mm jack	DC 5V/≥4A - 5.5x2.5mm jack	DC 5V/≥4A - 5.5x2.5mm jack	Powered via Jetson Nano
Matching Case	Model: T300 Case For T300 + Jetson Nano A02/ B01 With Power Switch With Reset Switch Support Cooling Fan Installation(Not supplied)	-	Model: T100 Case For T100 + Jetson Nano A02/ B01 With Power Switch With Reset Switch Support Cooling Fan Installation(Not supplied)	No matching case
PCB Size	12.3 x 7.9 cm	8.5 x 5.6 cm	10 x 8 cm	10 x 8 cm
Installation Video	-	-	Click to play	-

Add your comment

Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Sort by date Sort by score

Enable comment auto-refresher

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #2

14 hours 26 minutes ago

Score 0

Hello!

What voltage does "4010 3Pin PWM fan" require?

Is there a possibility to use 12V PC case 3pin fan instead?

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #1

3 months ago

Score 0

What's the difference between the M901 and the X10xx-series?

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Lisa

3 months ago

Score 0

Hi,Please refer to the table for comparison M901

Permalink