Comments log

This is a log of comments.

(newest | oldest) View (newer 500 | older 500) (20 | 50 | 100 | 250 | 500)

23:14, 26 July 2019 201.189.192.128 talk posted a new comment on Raspi UPS HAT Board (Hello, something needs to be done so that the battery starts charging again after the power source power has been interrupted for a few seconds?. the raspberry pi goes out because the charge does not start again)
06:13, 26 July 2019 82.43.202.247 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (I’ve got the same thing on a version A and version C screen. Disabling pixel doubling didn’t help. All the blacks are blue-ish, and it’s a bit yellow too. No idea how to fix. Using fresh install of Raspbian Buster.)
06:08, 26 July 2019 85.76.3.245 talk posted a new comment on Armor Case B (Bottom piece doesn't need anymore RAM cooling, as RAM is upper side, for case with fan.)
18:34, 25 July 2019 52.197.173.199 talk posted a new comment on Armor Case B (I want to check if the SD card can be covered by the case. As it put the card in a much safer place then.)
10:17, 23 July 2019 160.7.241.24 talk posted a new comment on Raspberry Pi IR Control Expansion Board (has anyone got this to work with VERSION="10 (buster)"?? I have tried these docs and it does not work I have tried two different expansion boards)
22:58, 19 July 2019 172.56.12.81 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Trying to run this screen with Arch Linux but keep getting booting errors. Is there a fix to run it with other Linux variants? Using a Pi 3B, also have a Pi 3B+)
16:46, 19 July 2019 81.133.39.55 talk posted a new comment on 2.2 LCD (Trying this with a Rpi4 but its not working, has there been some changes to the OS that require a different setup? Also any news on this case being modded for the Rpi4?)
16:46, 19 July 2019 160.0.193.103 talk posted a new comment on X830 (Is it possible to stack multiple X830's together?)
20:30, 16 July 2019 63.252.226.50 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Has anyone gotten this screen to work with Volumio? I was able to get it working with Raspbian, but with Volumio I get a blue screen and it fails to boot.)
04:52, 15 July 2019 62.216.209.155 talk posted a new comment on X870 (Hello, the x870 nvme board works me only when connecting it after bootup. Log shows low power warning. I read in the wiki that I can connect another micro-usb. So it is save to connect rpi and the board at the same time to 2A power at tge same time? I...)
10:24, 14 July 2019 110.169.10.84 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (I figured out about the borders. I just disable the double pixel in raspi-config then this will be fine. But the color problem is still.)
07:30, 14 July 2019 110.169.221.149 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Hi, My screen (Version-C) does not fully fit the diplay, they have border about 50px on each side. Also the display got a wrong color (Black goes blue, White go yellow and so on). I'm using recent raspbian buster version and download the latest drivers...)
01:30, 13 July 2019 187.160.117.202 talk posted a new comment on X400 V3.0 (How can configure de IR RECEIVER? Thanks for your support.)
02:19, 12 July 2019 81.132.8.168 talk posted a new comment on X820 (As the RPi 4 Network adapter and USB ports have been re-arranged and using the USB connector would line up (approx) with the Network port on the RPi 4, it won't work with the instructions provided. However, (NOTE: I haven't tried this) the USB interfa...)
08:53, 10 July 2019 76.106.88.242 talk posted a new comment on X720 (OK, I decided to plug it in right on the header and now the pi boots. So the only difference I only had one of the power management pins connected gpio17 I guess it needs all 3. I'll have to see what happens when I try to use 18 as a PWM.)
12:17, 9 July 2019 76.106.88.242 talk posted a new comment on X720 (when I turn it on the pi won't boot. Green and Red led on pi stay on, but if I turn the UPS off the pi boots. any ideas?)
12:15, 9 July 2019 76.106.88.242 talk posted a new comment on X720 (As far as pins I found the functional description, however does it need all the power management pins. I use 12, 13, 18, 19 for PWM.)
10:08, 9 July 2019 76.106.88.242 talk posted a new comment on X720 (is it safe to use the regular 18650 batteries 3.7V 2500mA each till I get the 18650B. Also I cannot stack this as I have other items stacked so it will be off to the side and so far looks like the only pins it needs are the I2C and the +5 and ground, c...)
16:38, 8 July 2019 112.169.32.140 talk posted a new comment on X830 V2.0 (I purchased the X300 v2.0. However, the size of the CASE differs from the data published by your company. Your material is 162x121x70 and the actual size is 162x121x80. Which one is right. Is the product sent incorrectly or is your data data wrong? Fo...)
11:10, 8 July 2019 49.35.125.195 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Is there support for Raspberry Pi 3A+?)
08:59, 8 July 2019 111.239.164.18 talk posted a new comment on X720 (Excuse me, Can I change the I2C address of RTC and battery's information?)
02:26, 8 July 2019 99.137.85.33 talk posted a new comment on X700 (Can I get this with the X720 Case without the X720 board? Why does step 5 have a picture of the X720 is this is the X700?)
01:29, 8 July 2019 174.236.136.140 talk posted a new comment on 10.1 inch LCD (2560x1600) (Can this be used with a Smartphone that has hdmi output (like s Note 8)?)
14:45, 7 July 2019 79.119.177.191 talk posted a new comment on X820 (Hello, Is the X820 board compatible with Raspberry Pi 4?)
14:32, 5 July 2019 Admin talk contribs posted a new comment on Aluminum Case-D (Hello sir This case for PI 4 will be release in 10 days. Please pay attention to us. https://geekworm.com/products/raspberry-pi-3b-3b-aluminum-alloy-metal-case-with-cooling-fan-heatsinks)
14:28, 5 July 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello friend, The X830 need to be update to be compatible with Raspberry Pi 4, please apy attention to geekworm.com thanks! Best regards, Cindy)
14:25, 5 July 2019 Admin talk contribs posted a new comment on Armor Case (Hi friend, The armor case for Raspberry Pi 4 will be release soon, please pay attention to our website: geekworm.com . Best regards, Cindy)
11:39, 3 July 2019 73.97.129.176 talk posted a new comment on Raspberry Pi IR Control Expansion Board (I am using Raspian Buster, and trying to record codes of a Sony remote. But it is not able to detect the buttons, even though mode2 is detecting the button presses on the remote.)
06:12, 3 July 2019 64.234.14.122 talk posted a new comment on Armor Case (Any idea on when the armor case is to be release for the Pi 4? I don't plan to run the 4 without a solid heatsink.)
14:18, 2 July 2019 46.6.196.80 talk posted a new comment on X830 V2.0 (Hello. It's compatible with the new Raspberry Pi 4?)
02:12, 30 June 2019 98.182.30.72 talk posted a new comment on Aluminum Case-D (Can I modify this case to fit the RPi 4B dimensions available here: https://www.raspberrypi.org/documentation/hardware/raspberrypi/mechanical/rpi_MECH_4b_4p0.pdf ?)
04:21, 29 June 2019 134.154.79.8 talk posted a new comment on Installation Guide For X850 V3.0 New Version (BTW, I used the following 120G SSD and it worked very well: (Amazon) Dogfish Msata 120GB Internal Solid State Drive Mini Sata SSD Disk: https://www.amazon.com/gp/product/B0754959YH/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1)
04:18, 29 June 2019 134.154.79.8 talk posted a new comment on Installation Guide For X850 V3.0 New Version (I would have expected that the manual would contain software instructions on how to format/configure the drive (mine originally showed up as /dev/sdb. I figured it out by Googling until I found this: https://thepihut.com/blogs/raspberry-pi-tutorials/1...)
01:38, 28 June 2019 36.69.200.20 talk posted a new comment on Raspi UPS HAT Board (Can I charge and supply the Raspberry Pi at the same time in a long time like 12 hours without breaking my battery?)
01:38, 28 June 2019 36.69.200.20 talk posted a new comment on Raspi UPS HAT Board (Can I charge and supply the Raspberry Pi at the same time in a long time like 12 hours without breaking my battery?)
18:58, 27 June 2019 Admin talk contribs posted a new comment on ESP32-LyraT (Hi friend, We suggest that you can refer to the official site: https://www.espressif.com/en/products/hardware/esp32-lyrat And contact with them for technicial support, thank you! Best regards, Cindy)
18:54, 27 June 2019 Admin talk contribs posted a new comment on Installation Guide For X850 V3.0 New Version (Hi, Please bed close to the router if this happens, also which SSD do you use?)
18:33, 27 June 2019 Admin talk contribs posted a new comment on X870 (Hello friend, Do you refer to the http://www.raspberrypiwiki.com/index.php/X870#Document about how to boot from X870? Please attach your order number with problem details to email: support@geekworm.com for us to check the details, thanks! Best regards...)
18:31, 27 June 2019 Admin talk contribs posted a new comment on X870 (Hello friend, Please attach your order number with problem details to email: support@geekworm.com for us to check the details, thanks! Also please refer to the wiki details first, thank you! Best regards, CIndy)
18:23, 27 June 2019 Admin talk contribs posted a new comment on Armor Case (Hi, Please don't worry, we are prepare to update the armor case to Raspberry Pi 4 version soon. Please pay attention to our site. Best regards, Cindy)
13:41, 25 June 2019 62.1.82.174 talk posted a new comment on Armor Case (The Rpi3 version is great, really helped. I hope you are getting ready for Rpi 4.)
05:58, 25 June 2019 199.249.233.22 talk posted a new comment on X870 (I don't even get the rainbow boot screen when the USB device is connected. I plugged it into the Windows PC and it recognized it and I re flashed it for giggles but nothing.)
05:33, 24 June 2019 160.3.224.66 talk posted a new comment on Installation Guide For X850 V3.0 New Version (I mounted mine this way but the WiFi was interfered with to the point I could not connect reliably. Way too much IF.)
00:41, 24 June 2019 94.204.252.30 talk posted a new comment on X870 (I have formatted the drive by connected it from the board directly to PC but it's still not being detected by Rpi.)
22:05, 23 June 2019 80.227.155.82 talk posted a new comment on X870 (I don't see the drive, after doing a fresh install. Didn't format the drive yet and put it in the board and attached to raspberry pi. Can you please suggest how can I mount it to raspberry and format it? Thanks in advance.)
16:01, 21 June 2019 87.253.240.0 talk posted a new comment on ESP32-LyraT (Would I be able to 1a. Receive an audio signal on Aux In, and convert it to a processable digital audio format (for short PDAF) 1b. Have one or more BT devices connected, and receive audio signals from there, then convert the signals to a PDAF 2. mo...)
10:50, 18 June 2019 Admin talk contribs posted a new comment on X830 (Hello friend, The X830 v2.0 board can boot directly from the hard drive. Best regards, Cindy/Geekworm)
10:22, 18 June 2019 Admin talk contribs posted a new comment on X720 (Hello friend, Please refer to here: http://www.suptronics.com/miniPCkits/x720-software.html Do you install the scrip? If any more questions, please contact us at support@geekworm.com Best regards, Cindy/Geekworm)
10:12, 18 June 2019 Admin talk contribs posted a new comment on X720 (Hello friend, Please attach your order number and order link to email: support@geekworm.com Also please show the destils, it is better to attach a video, thanks! Best regards, Cindy./Geekworm)
07:53, 18 June 2019 162.219.100.66 talk posted a new comment on LVDS To HDMI Adapter Board (Admin, that PDF does not answer the question.)
06:37, 18 June 2019 174.85.222.159 talk posted a new comment on X830 (is it required to still use a micro sd or can this boot directly from the hard drive)
00:25, 18 June 2019 165.225.50.184 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Hi, Does the version-A 2.8 inch Touch Screen for Pi zero W use SPI or I2C interfacing? Also, are any of those interfacing pins directly being used by the driver? Thank you in advance!)
21:04, 15 June 2019 179.209.194.139 talk posted a new comment on X735 (is the kodi installed on the Retropie? or only on rasbian?)
20:55, 15 June 2019 151.40.208.158 talk posted a new comment on Raspi UPS HAT Board (Does the Raspi UPS HAT Board keep the battery charged or I need to recharge the battery manually plugging a Dual Micro USB charging cable? Can a program running on the raspberry be PI notified when a switch from power supply to the battery occurs?)
13:35, 15 June 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Please check http://www.raspberrypiwiki.com/index.php/File:S-LH1080P-AUDIO-V17-Spec-20180504-1.pdf)
13:34, 15 June 2019 Admin talk contribs posted a new comment on X820 (Hello sir, please remove your msata ssd first, connect X850 to your computer via blue usb cable, check if can found the X850 device.)
13:32, 15 June 2019 Admin talk contribs posted a new comment on X820 (Hello, the USB 3.0 bridge is ready. The usb 2 is the bottleneck of raspberry pi. but someone use x850 or x820 on the other board such ROCK64. Maybe raspberry pi 4 supports USB 3.0)
17:35, 14 June 2019 37.231.112.205 talk posted a new comment on X820 (I’m having trouble with my x850 v3.0 board. Specifically my computer cannot see the installed mSATA board. It is a MYDIGITALSSD Super Boot 2 240gb ssd. Following your diagrams, all the hardware seems to be installed correctly. Is there a trick or do...)
13:20, 12 June 2019 24.22.117.194 talk posted a new comment on LVDS To HDMI Adapter Board (The second set of pins just destroys your monitor. Seriously, i plugged in there by accident and it fried the monitor.)
00:24, 12 June 2019 162.219.100.66 talk posted a new comment on LVDS To HDMI Adapter Board (Why are there two rows of pins on the top of the board? What is the second set used for?)
19:33, 11 June 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, sir Sorry, we don't understand your mean. case? please email to support@geekworm.com)
19:31, 11 June 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Sorry. sir. We will update the so file for python 3 soon.)
19:30, 11 June 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (This is not normal, at any time, as long as you plug in the PSU, the battery will be charged Please check if your battery cable is reversed. or email: support@geekworm.com)
06:01, 11 June 2019 38.126.112.138 talk posted a new comment on Raspi UPS HAT Board (which pin(s) does this supply power to the raspberry pi from?)
05:49, 11 June 2019 38.126.112.138 talk posted a new comment on Raspi UPS HAT Board (Running into an issue where when using the HAT, all of my pins are in use when I run i2cdetect -y 1. However this isn't the case when I connect my devices directly to my raspberry pi. Any idea why this would be happening?)
14:39, 10 June 2019 Admin talk contribs posted a new comment on X735 (Hello friend, We test this shell script base official Raspbian '2018-11-13-raspbian-stretch.img' version;other operating systems not be tested!)
14:38, 10 June 2019 Admin talk contribs posted a new comment on X820 (Hello friend, The current raspberry pi board only support USB2.0, the X820 support USB3.0, when use with Raspberry Pi it still USB2.0. But the ROACK64 support USB3.0, When use X820 with ROCK64 board, it will support USB3.0 speed. Best regards, CIndy)
14:34, 10 June 2019 Admin talk contribs posted a new comment on EXP GDC (Hello friend. Sorry, we can not confirm the compatibility.we you can google for some details, thank you!)
14:34, 10 June 2019 Admin talk contribs posted a new comment on EXP GDC (Hello friend. Sorry, we can not confirm the compatibility. please refer to:http://www.raspberrypiwiki.com/index.php/EXP_GDC#Recommended_Graphics_Card for the recomended graphic card.)
22:32, 8 June 2019 92.52.137.48 talk posted a new comment on X735 (Hi, I use Raspbian+Kodi on 3B+ + X735. How to add in the shutdown menu Kodi script X730shutdown.sh?)
19:09, 8 June 2019 210.146.184.221 talk posted a new comment on X820 (Is this device not for adding Raspberry Pi USB 2.0 to USB 3.0? When connecting Raspberry Pi to Coral's Edge TPU, it is a bottleneck that the Raspberry is USB 2.0. I was expecting to solve this, but does it mean that it is not a specification that meets...)
03:57, 7 June 2019 36.92.32.67 talk posted a new comment on EXP GDC (hello GDC EXP: can the latest VGA RTX 2060.2070.2080 series support this device?)
16:09, 6 June 2019 182.52.45.3 talk posted a new comment on Raspberry Pi IR Control Expansion Board (need to look at https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=235256)
15:24, 6 June 2019 182.52.45.3 talk posted a new comment on Raspberry Pi IR Control Expansion Board (I mean, this paragraph : LIRC Software)
00:41, 6 June 2019 186.86.30.30 talk posted a new comment on X400 (you can use any kind of wifi remote control to interact with the application running on raspberry to control your music, even a smartphone will be good for that.)
20:50, 5 June 2019 Admin talk contribs posted a new comment on Raspberry Pi IR Control Expansion Board (Hi, Could you please tell me which document does not work?)
17:40, 5 June 2019 118.173.28.135 talk posted a new comment on Raspberry Pi IR Control Expansion Board (The configuration explained in this document does not work anymore with the latest version 2019-04-08-raspbian-stretch-full)
17:33, 5 June 2019 189.40.75.117 talk posted a new comment on X735 (I'm glad your board is working ok tho. I recommend you to contact GeekWorm by email, to see if they can help you out now that it's clear that the X850 is not fully compatible with the X735. I would like to also share an idea. You can make a hole on t...)
09:54, 5 June 2019 99.1.245.133 talk posted a new comment on Raspi UPS HAT Board (after the pi is powered on, if micro usb is plugged into the ups hat, the battery does not charge. is this normal? this also occurs if the pi is powered on but has external power removed, reconnecting external power stops the battery from charging.)
07:37, 5 June 2019 96.32.232.110 talk posted a new comment on X735 (Well creating a Frankenstein cable isn't really an option unless I want to keep the top to the case off, which I don't. The cable has no way to pas trough from internal to an external micro USB port. I bought the case so all the parts would be enclosed...)
17:23, 4 June 2019 189.40.91.10 talk posted a new comment on X735 (What I recommend for a last attempt is to test only the rasp(with a sdcard) + X735. If possible. Because I'm starting to think that the X850 is not fully compatible with the X735. Even that you have a 5v 4a power adapter connected to the X735, it's st...)
17:22, 4 June 2019 189.40.91.10 talk posted a new comment on X735 (What I recommend for a last attempt is to test only the rasp(with a sdcard) + X735. If possible. Because I'm starting to think that the X850 is not fully compatible with the X735. Even that you have a 5v 4a power adapter connected to the X735, it's st...)
10:28, 4 June 2019 96.32.232.110 talk posted a new comment on X735 (I see no difference in these instructions or the shell script from what I have already installed. I compared the scripts and the one on github now is the same as I have already run. It would be helpful if the script was commented when changes are made...)
10:25, 4 June 2019 96.32.232.110 talk posted a new comment on X735 (I see mo difference in these instructions or the shell script from what I have already installed. I compared the scripts and the one on github now is the same as I have already run. It would be helpful if the script was commented when changes are made...)
09:52, 4 June 2019 71.47.162.47 talk posted a new comment on Raspi UPS HAT Board (I am trying to migrate my python2 app to python3 and got the following error message when running with python3. How can I fix this to work? import raspiupshat ImportError: /home/pi/build/raspiupshat.so: undefined symbol: Py_InitModule4)
18:34, 3 June 2019 36.92.32.67 talk posted a new comment on EXP GDC (can the Acer Aspire 4570Z and HP Presario CQ42-457TU be able to support?)
14:51, 3 June 2019 Admin talk contribs posted a new comment on X735 (Hi, We have do some update, please refer to Hardware and Software link at: http://www.raspberrypiwiki.com/index.php/X735#Document for more details, thank you!)
06:37, 2 June 2019 50.201.218.136 talk posted a new comment on X720 (Is there a support contact? I got mine, plugged it into my PI, installed the batteries, plugged power in to the usb power on the X720. It only gives ~3.6v on the 5v lines and 0v on the 3.3v lines. Is there something I need to do in order to get 5v out?)
06:28, 2 June 2019 96.32.232.110 talk posted a new comment on X735 (The mSATA SSD is a relatively small Samsung 850 EVO 120GB MZ-M5E120BW. the power supply is a SMAKN DC 5V/4A 20W Switching Power Supply with a 5525 male jack. The system boots up fine from a cold start pressing the momentary switch. It is after a moment...)
22:09, 1 June 2019 179.209.194.139 talk posted a new comment on X735 (Now that the we are sure the scripts and switches are ok. Let me ask you another thing, what is the power supply you are using? I am making this question because when it comes to usb booting, the sdd/hdd must have enough energy to turn itself on an...)
20:10, 1 June 2019 96.32.232.110 talk posted a new comment on X735 (OK so I checked both the latching switch positions and it turns out the white one was in the down position. I changed it to the up position but the behavior did not change. Using "sudo x730shutdown.sh" does work to shut down the system and power off, b...)
16:06, 1 June 2019 202.179.186.22 talk posted a new comment on EXP GDC (Hi Sir, it works on a Dell E4310 processor i5 (with Expesscard) with a Radeon HD 6850 video card? Thank you!)
16:05, 1 June 2019 81.174.138.207 talk posted a new comment on X720 (Could you please redo the shutdown test, but this time rather than pulling the power connector out of the board, switch off the wall-wart power supply at the mains. The amazon feedback recognises that your test does not shut down the pi, but claims th...)
16:51, 31 May 2019 179.209.194.139 talk posted a new comment on X735 (Let's just make some last tests Try to remove the X850, connect the x735 to the GPIO and be sure that both of the latching switches are up(the one with the white tap and the one next to the micro usb entrance). For the power switch(the on from the met...)
11:41, 31 May 2019 Admin talk contribs posted a new comment on 7 inch HDMI TFT Capacitive Touch Screen 1024x600 SKU:408999 (Hello Friend, Sorry, what do you mean by Add touch screen cage? Best regards, Cindy)
09:57, 31 May 2019 96.32.232.110 talk posted a new comment on X735 (I checked and verified the followng: 1. /etc/rc.local the last line is "/etc/x730pwr.sh &" 2. "x730pwr.sh" exists in /etc/ 3. "x730shutdown.sh" exists in /usr/local/bin/ 4. I ran "sudo apt-get install rpi.gpio" ind it installed successfully. If I hol...)
07:50, 31 May 2019 47.9.246.228 talk posted a new comment on 7 inch HDMI TFT Capacitive Touch Screen 1024x600 SKU:408999 (Add touch screen cage)
15:40, 30 May 2019 Admin talk contribs posted a new comment on EXP GDC (Hello friend, The gtx 950 video card is recommend to use, but we can not confirm the compatibility of your laptop Dell Inspiron 14R 3421 , hope to get your understanding! Best regards, Cindy/Geekworm)
15:30, 30 May 2019 Admin talk contribs posted a new comment on Raspberry Pi IR Control Expansion Board (Hello friend, Thanks for your question. Please send us your order number and probelm details, thank you! Best regards, Cindy/Geekworm)
15:29, 30 May 2019 Admin talk contribs posted a new comment on Raspberry Pi IR Control Expansion Board (Hello friend, Thanks for your question. Please send us your order number and probelm details, thank you! Best regards, Cindy/Geekworm)
15:05, 30 May 2019 170.79.45.59 talk posted a new comment on EXP GDC (Hi friend, do you think it works on a Dell Inspiron 14R 3421 processor i5 (with mini pci-e input) with a gtx 950 video card? Thank you brother!)
03:23, 30 May 2019 179.209.194.139 talk posted a new comment on X735 (Hi, So when you shutdown, how do you do it? By pressing the button for more then 3 secs or do you select shutdown in the menu? In case you are shutting it down by using Retropie, so this is the reason it is not working. But, the switch should be work...)
19:25, 29 May 2019 174.94.30.127 talk posted a new comment on Raspberry Pi IR Control Expansion Board (What position on the Gio pins do the controller board sit on ??)
19:23, 29 May 2019 174.94.30.127 talk posted a new comment on Raspberry Pi IR Control Expansion Board (What do the two buttons on the controller board do ???)
17:02, 28 May 2019 Admin talk contribs posted a new comment on 7 inch HDMI LCD (H) (Hello friend, The touch port is for you to use the screen touch function, if you need to use touch function, the USB cable should be connect to touch port. Best regards, Cindy/Geekworm)
16:44, 28 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hi, Please refer to the above photo, you can consider to use USB to Dual Micro USB Charging Cable. NOTE: the switch is disabled when you use USB to Dual Micro USB charging cable; The raspberry pi will be power on automatically after the battery capac...)
13:07, 28 May 2019 122.231.100.131 talk posted a new comment on RPi UPSPack (New UPSPACK coming : (with python program to monitor the battery) https://github.com/rcdrones/UPSPACK_V2/)
12:00, 28 May 2019 73.22.122.139 talk posted a new comment on X150 (Is there a case available?)
10:10, 28 May 2019 96.32.232.110 talk posted a new comment on X735 (I purchased the x735 and x850 and the metal case. I have followed the instructions above in this Wiki exactly to install the shutdown script. When I shutdown my Pi 3 B+ the system shuts off but the board does not power down. Also when I reboot it acts...)
04:31, 28 May 2019 70.171.230.247 talk posted a new comment on 7 inch HDMI LCD (H) (What is the Touch output/input on the end of the screen for?)
04:31, 28 May 2019 181.160.247.190 talk posted a new comment on Raspi UPS HAT Board (Hi, can I turn on the raspberry without pressing the button on the UPS HAT?)
19:13, 27 May 2019 Admin talk contribs deleted comment #374 on N100
15:10, 25 May 2019 67.160.206.136 talk posted a new comment on N100 (Installing is not easy at all. The most ridiculous (not even shown here) is the WiFi antenna; the antenna connector is supposed to be installed before the Jetson is placed in the box (actually even before the Jetson module is installed on the carrier b...)
14:41, 24 May 2019 Admin talk contribs posted a new comment on 10 inch LCD-C (2560x1600) (Hi, What can we help you?)
21:09, 23 May 2019 61.141.78.192 talk posted a new comment on 10 inch LCD-C (2560x1600) (123123123)
12:21, 22 May 2019 Admin talk contribs posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (Hi, The board has been discontinued now, the dimensions is 8.5x5.5cm. Best regards, Cindy)
12:19, 22 May 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello , The X830 v2.0 only support 3.5 inch SATA HDD, if you need to connect to SSD, you can refer to X850, X860 or X870, and you can refer to our official site: https://geekworm.com/collections/new-arrivals best regards, Cindy/Geekworm)
07:50, 22 May 2019 198.12.39.75 talk posted a new comment on X830 V2.0 (Se le puede conectar un SSD?)
04:43, 22 May 2019 74.134.210.171 talk posted a new comment on Raspi UPS HAT Board (Use the micro switch on the HAT to turn power to the Pi on and off. After your "shutdown -h now" command on the Pi, press and hold the micro switch on the HAT and the green LED will go out. The 4 white LED's are just showing the state of the 3.7v 2500...)
10:41, 20 May 2019 112.207.101.134 talk posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (What are the dimensions (length & wifth)?)
09:31, 20 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, 1. Please send us your order number and item link to support@geekworm.com. 2.Please also attach some photos or a video to show the details, thank you. 3.Please try to not used the momentary switch but use the on board power button to have a...)
20:56, 19 May 2019 174.231.135.46 talk posted a new comment on X735 (I am using momentary switch and after 1-2 seconds of holding the power button it is supposed to reboot but instead it instantly shuts off. 1. not rebooting 2. because it is not rebooting and instantly turning off I suspect its a forceful shutdown.)
15:16, 17 May 2019 Admin talk contribs posted a new comment on X735 (Hello, Could you please what project do you need to use? Maybe you can contact us with support@geekworm,com for more destails. Best regards, Cindy)
14:25, 17 May 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hello, This board is limited to LVDS output, the resolution must be the VESA standard, and the driver board should be at least V59 grade. Best regards, Cindy)
12:15, 17 May 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, Yes, The IR-CUT Camera is compatible with all generations of Raspberry Pi(Pi 3 Model B/ Pi 2B/ B+/ A+/ Zero).)
12:14, 17 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, It is a little hard to figure out the problem here. Could you please send us a detail video about the process? Please send to email support@geekworm.com . Please attach an order number and item link thanks! Best regards, Cindy)
19:20, 15 May 2019 86.134.26.26 talk posted a new comment on X735 (We need function in software to power off then power on after maybe 10 seconds. Reboot not sufficient to reset some USB devices. Power off/on cycle triggered by software and HW watchdog. Must be remote, not manual press switch. Do you have product to d...)
02:40, 15 May 2019 49.32.211.160 talk posted a new comment on LVDS To HDMI Adapter Board (Will this work for 800*480 output from LCDs?)
04:09, 14 May 2019 193.114.98.214 talk posted a new comment on RPi IR-CUT Camera (does this camera connect to the raspberry Pi zero ?)
13:10, 11 May 2019 200.105.254.229 talk posted a new comment on Raspi UPS HAT Board (By the way. I have not yet installed any drivers.)
13:09, 11 May 2019 200.105.254.229 talk posted a new comment on Raspi UPS HAT Board (Hi! Could you please explain the correct procedure to have the UPS turn off? This is what I am doing: 1. I first shutdown the Raspberry. `shutdown -h now` 2. Then I press the power pushbutton. The energy is gone on the Raspberry. 3. The UPS LEDs stay...)
04:35, 11 May 2019 181.198.15.236 talk posted a new comment on Raspi UPS HAT Board (Hi! I had the same issue once I left the Raspi running for a couple of hours. I think the SD got corrupted for some undervoltage. The undervoltage symbol used to appear on the right whether connected or not. Nonetheless, I left the UPS disconnected for...)
04:32, 11 May 2019 181.198.15.236 talk posted a new comment on Raspi UPS HAT Board (Nice!)
11:17, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello, your method is not suggest because power supply for X820 cannot be controlled by X735 and safe shutdown won't be implemented as well. Best regards, Cindy)
11:16, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, The GPIO4, GPIO17 and GPIO18 is used for power management.The rest is available for use. Best regards, Cindy)
09:13, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello, When istall the X735, you can power from the X735 board DC port by the power supply to X820 board by connect the 2pin cable as in the right photo of X735+X820 board.This is rigt way to power the kit. Thanks very much for your understanding! Best...)
09:10, 10 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Would you mind tell us what problem have you met? Please send us your order number and item link and with photos and problem details to email ： support@geekworm.com . Then we can help you with it, thanks very much! Best regards, Cindy)
09:05, 10 May 2019 Admin talk contribs posted a new comment on Armor Case (Hi, For 3B+, you need to use 3 pcs of the thermal pads. Please refer to the wiki page above photos!)
08:42, 10 May 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello friend, We do not test it on an Asus Tinkerboard S, and the safeshutdown function will not work with an Asus Tinkerboard S. Best regards, Cindy)
08:37, 10 May 2019 Admin talk contribs posted a new comment on X850 (Hi, Sorry, maybe no, if you need one, please contact us by sp@geekworm.com.)
00:26, 10 May 2019 84.84.53.102 talk posted a new comment on X850 (Hi Cindy, When will the USB 3.0 bridge be available as a separate item?)
23:15, 9 May 2019 94.138.44.146 talk posted a new comment on X830 V2.0 (Hello is it compatible with an Asus Tinkerboard S?)
00:09, 8 May 2019 189.51.183.52 talk posted a new comment on X735 (what are the GPIOs used in the script? Because I have some being used in other scripts and I didn't want them to conflict)
16:22, 6 May 2019 62.157.37.152 talk posted a new comment on Raspi UPS HAT Board (Continuing from the last question: In the video above the Dual Micro USB cable is used to power the system. Now at one point the cable is pulled from the wall plug. Now the system is in battery mode with the USB connector of the RPi and the UPS hat be...)
16:11, 6 May 2019 189.40.73.146 talk posted a new comment on X735 (What if I connect the x820 XH2.54 5v to the IN of the X735, and then connect the power supply to the x820. Will the safe sh work?)
15:35, 6 May 2019 89.97.236.20 talk posted a new comment on Armor Case (Thank you Cindy! In this thread someone is reporting different thickness, but I think mine are like the one you cited. Just to clarify more: which pads are needed on Pi3B+?)
14:58, 6 May 2019 Admin talk contribs posted a new comment on X822 (Hello sir, There is a USB HUB chip on the X822 board, so it is only need to connect one usb bridge or USB cable to provide the data of both hdd. Hope to get your understanding!)
14:56, 6 May 2019 Admin talk contribs posted a new comment on X822 (Hello, The X822 support 2 pcs 2.5 inch SATA hard drives, and the RAID 1 drives depends on the software not on hardware, hope to get your understanding!)
14:47, 6 May 2019 Admin talk contribs posted a new comment on 3.5 inch TFT 800x480@60fps (Thanks very much for your feeback!)
14:44, 6 May 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, sorry no, could you please tell us why you need the dimensions?)
14:41, 6 May 2019 Admin talk contribs posted a new comment on X350 (Hi, sorry, no.We dot not suggest to replace it.)
14:39, 6 May 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, We are so sorry, we can not confirm the compatibility.)
14:38, 6 May 2019 Admin talk contribs posted a new comment on X720 (Hi, It is said that it can be releazied by WOL client software.But we do not test this,hope to get your understanding!)
14:13, 6 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, If there is no external power , there is no need to connect the USB to Dual Micro USB Charging Cable.)
14:07, 6 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Sorry, it is not available now.)
19:20, 5 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, Yes, you are right, we will attched the photos of raspberry pi and X820 and X735 board later.)
14:35, 5 May 2019 62.157.37.152 talk posted a new comment on Raspi UPS HAT Board (Hi, Connecting two USB-cables to RPi and UPS means that the 5V input on the UPS is directly connected to the 5V-pins of the RPi (Pin 2 and 4, see schematic of RPi). What happens when no external power is available and the system switches to battery po...)
09:20, 4 May 2019 174.103.75.225 talk posted a new comment on X822 (Could this board support using two 2.5 SATA Hard drives as RAID 1 drives allowing the Raspberry Pi to function as a server?)
03:29, 4 May 2019 178.189.12.122 talk posted a new comment on X720 (Is it possible to power on the rpi on a predefined time?)
20:07, 1 May 2019 83.26.254.131 talk posted a new comment on EXP GDC (Is my laptop compatible (SAMSUNG NP350V5C-S0FPL) ?)
17:49, 1 May 2019 176.130.174.168 talk posted a new comment on RPi IR-CUT Camera (Hello, anyone knows the exact dimentions (or drawing) for the mechanical interface of the camera P/N 497358 ? Help will be apreciate)
11:10, 1 May 2019 222.110.24.108 talk posted a new comment on X350 (is that Omnidirectional microphone onboard ? could i replace onboard microphone better than now)
06:33, 1 May 2019 179.209.194.139 talk posted a new comment on X735 (to make the safe shutdown work. do I have to connect the x820 by the XH2.54 2Pin Cable to the x735 and connect the power supply to the x735?)
06:28, 1 May 2019 179.209.194.139 talk posted a new comment on X822 (do one usb provide the data of both hdd or us1 is for hdd1 and usb2 is for usb2?)
03:44, 1 May 2019 181.160.243.7 talk posted a new comment on Raspi UPS HAT Board (How can I control the switch from gpio?)
22:25, 30 April 2019 80.88.23.208 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Dimming the backlight via I2C is possible. It is also possible to switch the display off and on again. But there seems to be a problem with the standby mode: After waking from standby the display is extremely sensitive on touching the boarder. It flick...)
04:33, 30 April 2019 66.219.150.142 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Can you dim the backlight on the original version?)
09:13, 29 April 2019 Admin talk contribs posted a new comment on USB 16x2 RGB LCD (Hello, What problem have you met? which step is not working?)
02:50, 29 April 2019 73.58.121.199 talk posted a new comment on USB 16x2 RGB LCD (I'm still having issues installing usb2lcd. I have followed the instructions but it's not working for me, any idea why?)
14:31, 28 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, Thanks for your message. We can not confirm the compatibility, as we do not test each type of laptop model.So sorry for all the inconvenience. Maybe you can google for some information.)
14:30, 28 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, Thanks for your message. We can not confirm the compatibility, as we do not test each type of laptop model.So sorry for all the inconvenience.)
14:27, 28 April 2019 Admin talk contribs posted a new comment on X400 V3.0 (Hello, We just consult for some help, the I2C interface can be used to adjust audio volume.)
09:43, 26 April 2019 150.107.175.110 talk posted a new comment on X400 V3.0 (Using PCM5122 chip, can the I2C interface be used to adjust audio volume)
18:00, 25 April 2019 107.148.222.147 talk posted a new comment on EXP GDC (Hello My laptop is HP ElitBook 8540W, will my laptop compatible with the EXP GDC?)
01:09, 24 April 2019 79.99.75.233 talk posted a new comment on EXP GDC (Hello I have lenovo T430 i5 in windows 10 and GTX760. Will this work with the EXP GDC with the express card? (The laptop has express card port).)
19:09, 23 April 2019 Admin talk contribs posted a new comment on X850 (Hi, Thanks very much for your advice, we will consider it.)
08:43, 22 April 2019 Admin talk contribs posted a new comment on Armor Case (Hi, Thanks for your feedback. We will pay attention to this. Yes, it will happen in some item maybe because of batch production.)
08:41, 22 April 2019 Admin talk contribs posted a new comment on Armor Case (Hello, Thanks ! Maybe you can have a try,sorry I cant make sure what is it a MX-2 artic .)
15:46, 19 April 2019 Admin talk contribs posted a new comment on Armor Case (Hi, I just tested, big one: 1.39mm big one: 0.93mm middle one: 1.39mm small one: 1.39mm There are 4 pcs, but three of them with same thickness of 1.39mm, one of the big one is about 0.93mm. Best regards, Cindy/Geekworm)
15:36, 19 April 2019 Admin talk contribs posted a new comment on ESP32-LyraT (Hi, What can I help you?)
10:19, 19 April 2019 180.166.64.114 talk posted a new comment on ESP32-LyraT (12)
09:10, 19 April 2019 76.115.100.230 talk posted a new comment on Armor Case (Looks very cool (ha)! I'd worry about those mounting screws though, I only got 1 or at most 2 turns of thread engagement before it bottomed out, and they look and feel pretty fragile. I'm sure some people will strip these threads.)
08:56, 19 April 2019 76.115.100.230 talk posted a new comment on Armor Case (Just got mine- FWIW there are two thicknesses on the pale blue thermal pads, one is 0.78 mm and the other three are 1.25 mm thick. That includes the thickness of the backing paper, which is 0.15 mm just by itself.)
03:18, 19 April 2019 2.226.200.239 talk posted a new comment on Armor Case (Sorry, I can't reply directly. I mean... All ones. Maybe I rescued the one that goes the chip alone on the back, but I miss the two on top, if needed.)
01:05, 19 April 2019 89.156.45.81 talk posted a new comment on Armor Case (Hello, May I replace pads by a thermal compound like MX-2 artic ? Your product is awesome. BR, François.)
16:08, 18 April 2019 112.97.59.78 talk posted a new comment on Armor Case (Hello sir, Do you mean the big one or the small one? We can test the tickness for you!)
16:05, 18 April 2019 112.97.59.78 talk posted a new comment on LVDS To HDMI Adapter Board (Hello, Could you please tell us do you get the single 8 board or double 8 board? As they have different program, so one board can't be used as single 8 and double 8 the same time. Please refer to : File:S-LH1080P-AUDIO-V17-Spec-20180504-1.pdf If any m...)
04:00, 16 April 2019 2.226.200.239 talk posted a new comment on Armor Case (Hi! I moved the heatsink from a Pi2 to a Pi3B+ and the pads got disintegrated. May you point the thickness I need on which chip? ASAIK none on the SoC... but the others? Thanks.)
00:31, 16 April 2019 12.70.246.2 talk posted a new comment on LVDS To HDMI Adapter Board (Hello, I ran through the manual, but still do not see any indication of how to wire the board up for single channel LVDS. Can you please further clarify? Do I need to jump some of the pins of the programming interfaces? I need to get this up and run...)
18:40, 15 April 2019 Admin talk contribs posted a new comment on X400 V3.0 (Hello, please choose iqaudio-DAC .)
18:10, 15 April 2019 85.70.133.27 talk posted a new comment on X400 V3.0 (Which DAC model do I set with piCoreplayer? Thanks)
09:16, 15 April 2019 Admin talk contribs posted a new comment on Armor Case (Hello sir, Could you please tell us the order number? We are so sorry about the bad product problem ypoou have met, as it is volume production， so it will have such a problem, and we find it now, and when they come to us, we will try to check each on...)
00:21, 13 April 2019 82.102.24.164 talk posted a new comment on Armor Case (Sending mine back to Amazon. Went to screw the two halves together and the bolts threaded instantly. There is insufficient contact/overlap between the thread in each hole and the tip of the bolt, so the bolt just goes round and round after tearing the...)
17:32, 12 April 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, Do you refer to the file we attched? If not any inofmration about it, then it may be not.)
17:30, 12 April 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, We are so sorry to hear that, where do you order the board? Can you replace it at your side?)
17:26, 12 April 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello sir, What do you mean by old case? The X830 case has been updated to be suitable for both new X830 V2.0 version and X830 V1.1 version. Do you have any new suggestions with update? Best regards, Geekworn)
16:58, 12 April 2019 86.18.2.170 talk posted a new comment on X830 V2.0 (Is there any way of updating the old case?)
09:52, 12 April 2019 103.94.190.18 talk posted a new comment on Raspi UPS HAT Board (can i get battery consumption in Watt from the code?)
23:44, 11 April 2019 103.227.99.59 talk posted a new comment on Raspi UPS HAT Board (Capacitor C4 got burnt after running for a while. Any idea why did this happen?)
09:25, 11 April 2019 Admin talk contribs posted a new comment on 3.5 inch TFT 800x480@60fps (Hello, sorry, there is no information show the back light can be controled by software, hope to get your understanding!)
09:22, 11 April 2019 Admin talk contribs posted a new comment on X400 V3.0 (Hello, Please send your order number and item link you order to support@geekworm,com . Please describe the problem details clearly it is better if any pictures can help.)
09:22, 11 April 2019 Admin talk contribs posted a new comment on X400 V3.0 (Hello, Please send your order number and item link you order to support@geekworm,com . Please describe the problem details clearly it is better if any pictures can help.)
23:07, 10 April 2019 80.88.23.208 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Hi, is there a possibility to disable/enable the back light with software)
18:57, 10 April 2019 91.224.226.197 talk posted a new comment on X400 V3.0 (Is it normal, that the volume controller doesn't take effect on the cinch connectors?)
18:55, 10 April 2019 91.224.226.197 talk posted a new comment on X400 V3.0 (Hello, it seems that the output via headphone can make some noise from other electric components in the electric circuit. But via cinch connector it is not available. With my X400 V2.0 via headphone there are no unwanted noises.)
08:45, 10 April 2019 Admin talk contribs posted a new comment on X400 V3.0 (Hello sir, Yes, it is ok, the power supply requiremnet is DC 6-26V，( >=3A is recommend).)
08:44, 10 April 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello, Yes, it is ok, please make sure it is 12v.)
01:29, 10 April 2019 86.18.2.170 talk posted a new comment on X830 V2.0 (Would a 12v 5a power supply be ok?)
00:36, 10 April 2019 193.86.27.36 talk posted a new comment on X400 V3.0 (hi, may I use a power supply with paramaters 70W 24V 4A?)
09:23, 9 April 2019 Admin talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Hello, The screen use 565 mode, please refer to the GPIO PIN list here: http://www.raspberrypiwiki.com/index.php/File:PI_ZERO_W_LCD_PIN.ZIP The NC pin is not occupied by the screen, you can use it!)
18:23, 8 April 2019 51.154.58.95 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Hey I've got the V00BR Version:B, which 565 Mode is this screen using? I'd need to use the other GPIOs...)
11:41, 8 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, 1. The EXP GDC has to be used with the built-in wireless card. 2. Your laptop has to be disassembled to comfirm the interface type if no Expresscard interface. 3. Different versions, the interface is not the same.Please read the product page carefu...)
21:54, 7 April 2019 178.217.119.10 talk posted a new comment on EXP GDC (Good morning! I have a Lenovo G580 Laptop. Will this interface work with it?)
16:13, 4 April 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hi, Sorry, actually it is a DIY project, we can not know much about it, so sorry about the inconvenience.)
10:23, 4 April 2019 109.149.174.223 talk posted a new comment on Robot Expansion Board (Can i use an i2c LCD display with the hat ? I tried i2cdetect -y 1 to detect the address but the pi didnt list it . Is it because the hat is communicating with default pi i2c and another i2c device cannot be connected to the hat ?)
10:05, 4 April 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello, Sorry, we do not test it. So we can not show more details, hope to get your understanding!)
09:48, 4 April 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hi, Sorry, we do not have the schematics of the GPIO pins, but the raspberry pi wil take the full GPIO pin of the motor hat, please note.)
09:38, 4 April 2019 109.149.174.223 talk posted a new comment on Robot Expansion Board (Is it possible to get a schematics of the GPIO pins ??)
09:27, 4 April 2019 109.149.174.223 talk posted a new comment on Robot Expansion Board (Can i use a Lidar with the hat ? Lidar uses UART protocol . And if so do i have to initialise the i2c address of board on lidar script because lidar is a slave circuit on it own communicating with the hat which communicates with the pi . Is it possibl...)
18:22, 3 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, DO you have other graphic card to have a try?)
17:10, 3 April 2019 85.103.166.231 talk posted a new comment on EXP GDC (Yes I have downloaded and installed the Auguest 2016 driver (372.70 version). However there is still no detection of eGPU by the system :( :( as in nothing will show up in device manager)
09:06, 3 April 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Do you refer to this user manual? http://www.raspberrypiwiki.com/index.php/File:S-LH1080P-AUDIO-V17-Spec-20180504-1.pdf)
09:03, 3 April 2019 Admin talk contribs posted a new comment on RPI HIFI AMP (Hello friend, When install the AMP board on the Raspberry Pi, it will take the full GPIO PIN of your raspberry pi board. Hope to get your understanding! Best regards, Geekworm)
09:01, 3 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hello friend, You just need to buy a NGFF CABLE from where you have bought the EXP GDC, to make sure that the GDC dock is the same.)
09:01, 3 April 2019 Admin talk contribs deleted comment #262 on EXP GDC
09:00, 3 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hello friend, You just need to buy a NGFF CABLE frm where you have bought the EXP GDC, to make sure that the GDC dock is the same.)
08:59, 3 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, For GTX 1060 1070 1080 They are compatible with EXP GDC, but you must install the Auguest 2016 driver(372.70 version). Do you install the driver?)
08:59, 3 April 2019 Admin talk contribs deleted comment #260 on EXP GDC
08:59, 3 April 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, For GTX 1060 1070 1080 They are compatible with EXP GDC, but you must install the Auguest 2016 driver(372.70 version). Do you install the driver?)
08:56, 3 April 2019 Admin talk contribs posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (Yes, this blue one is not available now. Mayebe you can refer to :http://www.raspberrypiwiki.com/index.php/RPi_UPSPack)
05:13, 1 April 2019 88.91.168.122 talk posted a new comment on RPI HIFI AMP (Which GPIO pins does it use?)
18:09, 31 March 2019 84.33.67.195 talk posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (Do you mean that the product will not available any more? "Sorry, there is no such a function. The product is disconitnued now.")
15:22, 31 March 2019 88.238.194.89 talk posted a new comment on EXP GDC (Dear sir, i have the EXP GDC dock mini PCI version. Now i want to try it with NGFF laptops. My question is, should I purchase a new EXP GDC dock NGFF version and a cable? or can I use an NGFF cable and with the same mini PCIe dock that I have? thank yo...)
02:01, 31 March 2019 155.186.108.13 talk posted a new comment on X850 (With regards to the USB bridge, please consider encasing it in plastic with a protrusion allowing a finger-tip grip for removal.)
20:59, 30 March 2019 173.184.19.134 talk posted a new comment on LVDS To HDMI Adapter Board (How do I configure this board for 1 channel LVDS instead of 2 channel LVDS?)
03:11, 30 March 2019 88.238.194.89 talk posted a new comment on EXP GDC (dear sir, thank you very much for your reply! so i have already tried hotpluging the mini PCIe cable from sleep mode, unfortunatelly still no success :( Can you please explain what you mean by "Replug the two sides connection interface of Mini PCI-E"?...)
15:13, 28 March 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello sir, Thanks for your message. Sorry, it is not possible to o access the programming to control the fan speed. If you figure out a way for the pi to control the fan,please tell us, we are willing to know. Best regards, Cindy/Geekworm)
15:03, 28 March 2019 Admin talk contribs posted a new comment on X830 (Hello sir, The 2 pin 12 Volt input port is XH2.54 port, hope this will help.)
09:48, 28 March 2019 104.205.52.118 talk posted a new comment on X830 V2.0 (Hello X830 Team, I noticed that the fan speed varies over time. Considering it's only a 2 wire connection I assume the board is controlling the voltage. Is there a way to access the programming for some/any fan control? Ideally I'd like to run the fa...)
01:41, 28 March 2019 134.129.20.1 talk posted a new comment on X830 (Referring to the 2.0 version, What is the connector needed for the 2 pin 12 Volt input. Not the 5.5mm x 2.5mm barrel connector. The one on the top of the board that looks like a some version of a JST connector. Thanks!)
19:32, 27 March 2019 178.155.5.143 talk posted a new comment on 3.5 inch TFT 800x480@60fps (For Raspberry 3B plus need add sting "dtoverlay=dpi24" in config.txt for 24-bit RGB)
10:51, 27 March 2019 Admin talk contribs posted a new comment on EXP GDC (Hello sir, We are so sorry, we know very little about the gtx 680, so we can not confirm, hope to get your understanding! Maybe you can google to find if any suggestions.)
16:39, 26 March 2019 181.135.251.100 talk posted a new comment on EXP GDC (is the gtx 680 compatible and does the adapter cause the graphic to have a bottleneck or operate at less capacity?)
14:21, 26 March 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello sir, We get your email, please see our reply with the email,thanks!)
13:49, 26 March 2019 37.194.162.111 talk posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (At what tension will the accumulator be powered off?)
09:30, 26 March 2019 Admin talk contribs posted a new comment on EXP GDC (Hello sir, We consult for some help, your laptop need to use this NGFF M.2 A key version EXP GDC. This one: https://www.aliexpress.com/store/product/V-8-0-EXP-GDC-Laptop-External-Independent-Video-Card-Dock-NGFF-Version/1048722_32662292718.html)
09:25, 26 March 2019 Admin talk contribs posted a new comment on 2.2 LCD (Hi,so glad to hear that our wiki page would be help. Please also pay attention to our official site: geekworm.com. thank you!)
09:24, 26 March 2019 Admin talk contribs posted a new comment on EXP GDC (Hello sir, We suggest that you can try as follow: 1. Try it like the sleep way.Do not connect the cable of graphic card, start up your laptop, go to sleep when you go in the system, then plug the cable to wake it up. 2. Please check the memory stick (n...)
09:18, 26 March 2019 Admin talk contribs posted a new comment on EXP GDC (Hi， yes, the exp gdc is support Windows 10.)
09:12, 26 March 2019 Admin talk contribs posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (Hi, Sorry, there is no such a function. The product is disconitnued now.)
19:18, 25 March 2019 41.229.96.2 talk posted a new comment on Robot Expansion Board (I am working on servo motor PWM channels and I didn't how to work on channels #1 #14 #15 because the servotest.py is working on channel #0 by default)
20:04, 24 March 2019 88.238.200.83 talk posted a new comment on EXP GDC (dear support, I have a problem regarding my EXP GDC dock. I have already ordered the dock (mini PCIe version). And after completing the setup as indicated in the manual and connecting the power cables plus the mini PCIe cable, I do not get GPU detectio...)
22:38, 23 March 2019 88.238.200.83 talk posted a new comment on EXP GDC (will the EXP GDC work with Windows 10?)
09:38, 23 March 2019 216.165.95.186 talk posted a new comment on 2.2 LCD (Thank you for this!!! It's the first guide that works :))
07:29, 23 March 2019 181.135.251.100 talk posted a new comment on EXP GDC (Good afternoon I have a doubt my pc is an acer e-5 475g I will put a link with the image of my board, my question is the following my adapter wifi network is with port NGFF would have to buy the exp gdc with that port, and also I have another doubt nex...)
18:57, 22 March 2019 216.21.18.193 talk posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (Is there a script that will detect USB-A power loss and will gracefully shutdown the Pi)
14:30, 22 March 2019 27.38.254.32 talk posted a new comment on Smart Fan and Power Expansion Board (Hello sir, Sorry, we do not try to use it this way, so it is not syggested to use the fan and power board to power the X820 expansion board, hope to get your understanding! Best regards, Cindy/Geekworm)
10:30, 22 March 2019 27.38.254.32 talk posted a new comment on X850 (Hello, We have got some requirement feedback of use NVME M2 SSD and M.2 NGFF SATA SSD. So the X870 board for NVME M2 SSD, and the X860 board for M.2 NGFF SATA SSD both are under development now, and are planning to be released at maybe the end of Apri...)
23:02, 20 March 2019 47.16.153.94 talk posted a new comment on Smart Fan and Power Expansion Board (Can this board be used to power the X820 expansion board?)
16:02, 20 March 2019 69.121.158.200 talk posted a new comment on X850 (Can the SATA bridge controller support NVMe SSD's? Is the SATA bridge controller the appropriate factor for me to consider when trying to determine whether or not an(any) NVMe SSD would be an appropriate match for my... Rpi 3 b+?)
11:26, 19 March 2019 Admin talk contribs posted a new comment on X850 (Hello, Thanks for your attention, the USB 3 bridge is being produed and will be available early April, please pay attention to geekworm official site blog: https://geekworm.com/blogs/raspberry-pi Best regards, Cindy)
01:18, 19 March 2019 84.84.53.102 talk posted a new comment on X850 (I use the X850 with a Rock64-board. Sadly the USB-bridge is only USB 2, so I must use the cable to get USB 3 speed. The bridge is a neat solution. Any plans for a USB 3 version?)
16:04, 18 March 2019 Admin talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Hello, The 2.8inch screen is consist of display screen and touch screen, The display screen is DPI, and the touch screen is SPI. And the screen is 16 bit color and RGB565 mode. Best regards, Cindy)
11:35, 18 March 2019 Admin talk contribs posted a new comment on Armor Case (Hello, The armor case is aluminum alloy material, and we have sold many out, we have not get any feedbacj that it will WiFi and Bluetooth signal. Please pay attentin to our official site: https://geekworm.com/ Best regards, Cindy/Geekworm)
02:37, 18 March 2019 107.242.117.10 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (This is SPI? Or HDMI? 16 bit color or 24 or 32?)
02:44, 16 March 2019 97.120.90.4 talk posted a new comment on Armor Case (Is the Armor Case a Faraday cage? Does it block WiFi and Bluetooth?)
18:41, 15 March 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, Please refer to here first: http://www.raspberrypiwiki.com/index.php/File:EXP-GDC-Operating-Guide.zip)
11:24, 15 March 2019 189.189.12.109 talk posted a new comment on EXP GDC (I have laptop hp pavilion 15-aw003l, and in my bios I do not find any of the options to disable and at the time of powering on the laptop with exp gdc, I use nggf and a gtx 950 card my screen turns black and when I connect the graphical card to the ext...)
14:32, 14 March 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Maybe we can not understand your meaning clearly.Can you contact us by email and attach some photo or details? Best regards, Cindy/Geekworm)
11:50, 14 March 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Could you please check if your battery 2pin port the red and black cable if in the right place as the photo above. Or you can change another 3.7v battery to have a try. Best regards, Cindy/Geekworm)
11:18, 14 March 2019 Admin talk contribs posted a new comment on RPi UPSPack (Hello friend, For the PONIT 3:3- After, the battery begins to discharge, but the red LED remains fixed and the charging is no longer started, so the battery is completely discharged and the Raspberry Pi stops - KO. How do you connect each device? Plea...)
04:00, 14 March 2019 109.151.141.225 talk posted a new comment on Raspi UPS HAT Board (Hello, my UPS HAT when fully charged and on power will stop the ouput power to raspberry pi then start again then stop. Is this normal when fully charged and on power ? Thank you)
17:58, 13 March 2019 62.15.136.19 talk posted a new comment on RPi UPSPack (Hello! I have a problem: 1- Feed the UPS and connect a Raspberry Pi. Everything works and indicates that the battery is charging (red LED flashes) - OK. 2- After a while, the red led stays fixed (battery charged) - OK. 3- After, the battery begins to d...)
14:16, 13 March 2019 202.46.129.70 talk posted a new comment on Raspi UPS HAT Board (how can i calibrate the battery? from the LED indicator it still blink (2 LEDs), but from the program shows 0%, then about in hour, my Raspi run out of battery)
09:51, 6 March 2019 Admin talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Hi, Thanks for your file, but our 2.8 inch screen is not waveshare product, please note, thank you very much. Best regards, Cindy/Geekworm)
17:03, 5 March 2019 102.248.105.97 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Kindly include the instructions for this product on this same page for others gpio pwmc 1 # set clock 1000 makes noise for me gpio -g mode 18 pwm # enable PWM on GPIO18 gpio -g pwm 18 1010 # change screen brightness to 975 range 0 - 1024...)
11:51, 4 March 2019 Admin talk contribs posted a new comment on 3.2 Inch TFT Lcd Touch Screen SKU:340835 (Hello sir, The 3.2 inch screen has been discontinued now, and all the information are on the page, we can not get any more detils now, sorry! Best regards, Cindy/Geekworm)
16:45, 2 March 2019 62.143.143.243 talk posted a new comment on 3.2 Inch TFT Lcd Touch Screen SKU:340835 (Is there a a way to dim the backlight ?)
10:35, 27 February 2019 Admin talk contribs posted a new comment on X820 (Hello, We suggest that you refer to here on the official site about How to boot from a USB mass storage device on a Raspberry Pi: https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md Best regards, Cindy)
03:54, 27 February 2019 121.200.15.236 talk posted a new comment on X820 (Hi All Once the HDD is installed, can I boot from a USB Stick to install Linux onto the internal HDD as it is or are other commands/configuration needed as of 1/2/2019? I know some commands previously were needed.)
18:31, 26 February 2019 Admin talk contribs posted a new comment on X730 (Hello sir, we will release the X735 and the matching case for X820+x735 soon. Harry /Geekworm)
14:21, 25 February 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello dear friend, You can modify the I2C address by shortcut the A0~A3 on the board (shortcut A0 and A1, shortcut A1 and A2...), thus you can get the different I2C address. But we do not test or try this, hope to get your understanding!)
03:49, 25 February 2019 76.126.103.90 talk posted a new comment on Robot Expansion Board (Is there a way to stack two of the Motor HAT in order to be able to drive 4 stepper motors ?)
16:17, 23 February 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, The UPS HAT board is with standard Raspberry Pi Pi HAT size!)
13:48, 23 February 2019 112.215.175.209 talk posted a new comment on Raspi UPS HAT Board (what dimension of board?)
09:39, 21 February 2019 Admin talk contribs deleted comment #202 on PINE A64
09:39, 21 February 2019 Admin talk contribs posted a new comment on PINE A64 (Hello sir, We suggest that you can ask for help from the official website: https://support.pine64.org/portal/home Best regards, Geekworm)
09:32, 21 February 2019 Admin talk contribs posted a new comment on PINE A64 (Hello sir, We suggest that you can ask for help from the official website: https://support.pine64.org/portal/home Best regards, Geekworm)
09:29, 21 February 2019 Admin talk contribs posted a new comment on X820 (Hello sir, For the Raspberry Pi 3B+ turorial you need to refer to raspberry pi official site. https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md The abvove page is mainly turorial for Raspberry Pi X820 board.)
01:26, 21 February 2019 64.33.242.15 talk posted a new comment on PINE A64 (I have 2 of the first model's both with 2 gig ram and both with the add-on bluetooth and wifi cards. One is mounted in a sort of tablet setup running Android, the other in a clear semi-case, it had a screen set atop it but the wires ripped so now I ac...)
17:45, 20 February 2019 104.194.218.185 talk posted a new comment on X820 (Hi, Is this the same turorial for the Raspberry P3b+ ?)
11:24, 20 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, GTX 1050 or GTX 1050TI or AMD CARD is not recommend to use. Do you try the The list of recommended graphics card: GTX650 GTX660 GTX670 GTX750 GTX760 GTX950 GTX960 GTX970 GTX980 GTX1060 GTX1070 GTX1080 ?)
02:53, 20 February 2019 72.180.93.212 talk posted a new comment on EXP GDC (I’ve been trying to help a friend install a GTX 1050 egpu on his HP 8470p EliteBook (which is a laptop on the supported list). He has 8 gigabytes of ram and an integrated HD 5000 graphics chip. He has tried both the Mini PCI-E version and the express...)
08:53, 15 February 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Could you please show some more details? Please attached some photos about your data. You can contact us by support@geekworm.com , please tell us your order number and product link of where you buy it, thanks!)
21:09, 14 February 2019 213.227.32.73 talk posted a new comment on Raspi UPS HAT Board (Hello, when I measure the battery capacity I get values over 100%. For this measure I use the formula that appear in this document "File:How-to-use-via-i2c.pdf". I'm missing something?)
11:18, 14 February 2019 Admin talk contribs posted a new comment on X830 (Hi, You can get it at our official site: https://geekworm.com/products/raspberry-pi-x830-3-5-inch-sata-hdd-hard-disk-drive-storage-expansion-board)
18:26, 13 February 2019 178.78.224.56 talk posted a new comment on X830 (hur kan jag skaffa X830 moderkort till case)
15:28, 13 February 2019 84.219.193.22 talk posted a new comment on X830 (hur kan jag skaffa det)
15:27, 13 February 2019 84.219.193.22 talk posted a new comment on X830 (jag söker efter ett sånt kort http://www.raspberrypiwiki.com/index.php/File:IMG_4253-3B-Plus.jpg)
09:03, 13 February 2019 Admin talk contribs posted a new comment on X400 (Hello, There is no information show this board can be remote control.)
00:11, 13 February 2019 213.205.194.137 talk posted a new comment on X400 (How do i setup a remote control to use with this board??)
16:38, 12 February 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, Sorry, we can not confirm about this.)
16:35, 12 February 2019 Admin talk contribs posted a new comment on Armor Case (Hi, Please refer to here: https://geekworm.com/products/raspberry-pi-aluminium-alloy-metal-armor-cooling-case-with-dual-fan It is very easy to install. Best regards, Cindy/Geekworm)
16:34, 12 February 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Sorry, we can not confirm about if this board can convert any LVDS data to RAW HDMI out.)
16:32, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Which version does my laptop use? Hi,Thanks for your email. 1. The EXP GDC has to be used with the built-in wireless card. 2. Your laptop has to be disassembled to comfirm the interface type if no Expresscard interface. 3. Different versions, the inter...)
16:31, 12 February 2019 Admin talk contribs deleted comment #183 on EXP GDC
16:31, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, EXP GDC is a DIY product, we suggest you can google to find more useful information.)
16:31, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, EXP GDC is a DIY product, we suggest you can google to find more useful information.)
16:30, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, Sorry, we do not test it.)
16:29, 12 February 2019 Admin talk contribs posted a new comment on X820 (Hello, Please refer to: http://www.raspberrypiwiki.com/index.php/X830_V2.0 This X830 V2.0 board support to install 3.5 inch SATA HDD, and with a match metal case. Best regards, Cindy/Geekworm)
16:26, 12 February 2019 Admin talk contribs posted a new comment on X850 (Hello, Please see the first photo on the right, it is Micro USB DC 5V. Best regards, Cindy/Geekworm)
16:18, 12 February 2019 Admin talk contribs deleted comment #178 on X830
16:18, 12 February 2019 Admin talk contribs posted a new comment on X830 (Hello, Sorry, the X830 has USB3.0 port but now the Raspberry Pi only support USB2.0, so the transfer rates will be USB2.0. Maybe in the future the Raspberry Pi 4 will support USB3.0. Best regards, Cindy/Geekworm)
16:17, 12 February 2019 Admin talk contribs posted a new comment on X830 (Hello, Sorry, the X830 has USB3.0 port but now the Raspberry Pi only support USB2.0, so the transfer rates will be USB2.0. Maybe in the future the Raspberry Pi 4 will support USB3.0. Best regards, Cindy/Geekworm)
16:14, 12 February 2019 Admin talk contribs deleted comment #176 on X350
16:14, 12 February 2019 Admin talk contribs posted a new comment on X350 (Hello, The X350 and Raspberry Pi is connected by the USB bridge, does not require external power supply for X350, and we upload the X350 board diagram above, please check the details. Best regards, Cindy/Geekworm)
16:14, 12 February 2019 Admin talk contribs posted a new comment on X350 (Hello, The X350 and Raspberry Pi is connected by the USB bridge, does not require external power supply for X350, and we upload the X350 board diagram above, please check the details. Best regards, Cindy/Geekworm)
15:54, 12 February 2019 Admin talk contribs deleted comment #174 on X150
15:54, 12 February 2019 Admin talk contribs posted a new comment on X150 (Hi, The X150 board is powered by Raspberry Pi, and you can Power the X150 via JST XH2.54 connector or USB port as the photo show above. Best regards, Cindy/Geekworm)
15:54, 12 February 2019 Admin talk contribs posted a new comment on X150 (Hi, The X150 board is powered by Raspberry Pi, and you can Power the X150 via JST XH2.54 connector or USB port as the photo show above. Best regards, Cindy/Geekworm)
23:22, 11 February 2019 172.56.6.104 talk posted a new comment on RPi IR-CUT Camera (Will M12 lenes work on this camera?)
13:41, 11 February 2019 88.66.73.76 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Hi, with enabling the I2C master functionality the display module is shown as I2C slave with address 0x1C. Executing an i2cdump returns some data like 'Single Click.Button Status : ', 'sleep.Screen' etc. It looks as if it would be possible to talk t...)
05:01, 10 February 2019 73.215.96.52 talk posted a new comment on Armor Case (Where's the installation instructions for the Raspberry Pi Armor Aluminum alloy Case A?)
23:26, 7 February 2019 139.143.65.36 talk posted a new comment on LVDS To HDMI Adapter Board (Hi, I am wondering if this board can convert any LVDS data to RAW HDMI out? Meaning not strictly display signals. Any thoughts? Many Thanks!)
13:20, 7 February 2019 189.204.179.61 talk posted a new comment on EXP GDC (eh my question is if it works asus k52jt with adactador exp exp see 8 e3 with pci ,,,,,,,,, I want to try it with amd radeon 240 r7 ,, well with this card inte to use it with a lonovo t430 but I get error 12 and when I install driver amd error comes ou...)
04:07, 4 February 2019 88.224.200.254 talk posted a new comment on EXP GDC (is it possible to use the exp gdc dock with the new Nvidia Geforce RTX series (RTX 2060, 2070, 2080 and 2080 ti)?)
20:21, 2 February 2019 37.248.253.103 talk posted a new comment on EXP GDC (In general: better performance is with pcie or express card? (for 1th gen i core processors (i7 620m))
06:07, 30 January 2019 12.94.93.158 talk posted a new comment on X820 (Would be nice to have a case that handles a 3.5" inch drive. Just something I would want, but nobody else is complaining.)
02:38, 30 January 2019 91.160.108.4 talk posted a new comment on X850 (Hi, i had same problème with the screws. But I had another problem when I try to connect 1tb ssd disk. It's seems like there is not sufficient power . Blue Led is on and not blinking like usual. Have you an idea of how much Secondary power i need . 5...)
01:06, 30 January 2019 200.6.35.101 talk posted a new comment on X830 (I don´t understand how you can get USB 3.0 transfer rates when the RPi usb port is 2.0. Can you clarify?)
08:42, 29 January 2019 108.69.22.105 talk posted a new comment on X350 (This does not explain how to connect the 5vdc power to the card. Do you use a cable from the raspberry pi's power or do you need an independent power supply? what kind of cable is required for the power supply? What plugs in to the USB connector, is it...)
03:48, 29 January 2019 98.168.248.188 talk posted a new comment on X150 (What is the power input requirements for the hub? I see a 5v printed on the board, but whats the amperage, and is another piece required for purchase?)
19:09, 28 January 2019 27.38.254.57 talk posted a new comment on RPi UPSPack (Hi sir, Sorry that it can't monitor UPS battery status from PI OS. But it has 4+2LED to shows charger and discharger, battery power status. Best regards, Geekworm Store)
01:30, 28 January 2019 78.200.17.78 talk posted a new comment on RPi UPSPack (Thank for this product and nice wiki page. Love mine :-) Just a question : any way to monitor UPS battery status from PI OS ?)
17:52, 26 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, 1. First please check according to the photo above of the 2.0b portof your battery to see if the red cable and black cable is in wrong side. 2.Please Send us your order number and item URL to support@geekworm.com about the problem details. B...)
00:23, 26 January 2019 37.47.175.232 talk posted a new comment on Raspi UPS HAT Board (Voltage and percentage values returned by ups-read or python module are not changing. Am I missing something? I'd left my Raspberry Pi Zero W on battery last night and it was without juice by the morning, but I didn't receive any changes notifications...)
09:23, 23 January 2019 Admin talk contribs posted a new comment on 10 inch LCD (Hi, Sorry, we do not have tv that goes on battery .)
04:56, 23 January 2019 212.251.176.36 talk posted a new comment on 10 inch LCD (hei . har du tv som går på batteri???)
14:06, 22 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Sorry, the ups hat board is not support to stack to use, you can not use two of these modules at the same time . Best regards, Geekworm)
02:34, 22 January 2019 79.114.1.99 talk posted a new comment on Raspi UPS HAT Board (Can two of these modules be used at the same time on a raspberry pi 3b+? Each module on top of the other?)
12:46, 21 January 2019 Admin talk contribs posted a new comment on X830 (Hello, Do you order this X830 board? This X830 board will be updated to a new version in this week. If you do not make the orde,you can wait and check for the new version. If you ordered the X830 v1.1 version, please contact us by email, thanks! Best r...)
09:12, 21 January 2019 Admin talk contribs posted a new comment on Raspberry Pi Zero W (Hello sir, We suggest that you can refer the official website: https://www.raspberrypi.org/products/raspberry-pi-zero-w/ Best regards, Cindy/Geekworm)
09:11, 21 January 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, 1. The EXP GDC has to be used with the built-in wireless card. 2. Your laptop has to be disassembled to comfirm the interface type if no Expresscard interface. 3. Different versions, the interface is not the same.Please read the product page carefu...)
23:54, 20 January 2019 185.107.47.171 talk posted a new comment on Raspberry Pi Zero W (I wish this page was more detailed, for example, which 'single-core CPU'? part number?)
16:50, 20 January 2019 212.95.6.1 talk posted a new comment on X830 (Hello, I searched for some documentation for the pin headers, but I couldn't find it, so: 1.: I suggest the pinout from 'PWR SW' is: red/black as LED-pin and blue/white as switch-pin. 2.: How much current can I draw from the pin header '12V GND 5V1'...)
08:08, 20 January 2019 46.134.159.203 talk posted a new comment on EXP GDC (Hi, I have asus n61jvand gtx 750, which is compatible with exp GDC. Which version of exp GDC is better: with express card or with mini PCI E?)
12:03, 18 January 2019 Admin talk contribs posted a new comment on EXP GDC (Hello sir, Do you connect the External display to your GTX 760 ? If you connect the external display, please use the External display as mian display to have a try, thanks! Best regards, Cindy/Geekworm)
10:01, 18 January 2019 Admin talk contribs posted a new comment on RPi UPSPack (Hello sir, You can order the Raspberry Pi UPS Pack board from Geekworm Official Website: https://geekworm.com/products/raspberry-pi-poe-hat-ups-lithium-battery-expansion-board And it has some difference, you can check the details by compare them. If an...)
05:30, 18 January 2019 188.86.66.171 talk posted a new comment on EXP GDC (Good evening, I have a toshiba satellite L50-A-18R laptop, I changed the hard drive to a 500 GB Samsung SSD, I added 4 GB more of DDR3L RAM to 1600MHz (in total I have 8 GB), but, once I have everything assembled (article: https://es.aliexpress.com/ite...)
03:53, 18 January 2019 114.29.250.137 talk posted a new comment on RPi UPSPack (Can i know where i can by this from? and does is it similar to "http://www.raspberrypiwiki.com/index.php/Raspi_UPS_HAT_Board"?)
15:33, 17 January 2019 Admin talk contribs posted a new comment on 3.5 inch TFT 800x480@60fps (Hello, We do not get any update information. What problem have you met? Best regards, Cindy/Geekworm)
19:59, 16 January 2019 185.80.28.5 talk posted a new comment on 3.5 inch TFT 800x480@60fps (""Note: If you are using Pi 3, please add this to the config.txt files;(This setting is to shield the interference of Bluetooth interface. We will update the system later.) [DON'T USE IT IF YOU USE PI 3B+] dtoverlay=vga666 dtoverlay=pi3-disable-bt-o...)
15:10, 16 January 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hello sir, If it not listed, then it will not support, and also we can not guarantee the compatibility, hope to get your understanding!)
14:45, 16 January 2019 148.64.3.82 talk posted a new comment on LVDS To HDMI Adapter Board (Hi, I know it states that it must be VESA standard, but i will still try my luck to ask :D Does it support resolution 1920 x 720 @ 60hz? Thanks in advance!)
10:11, 16 January 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hello sir, The double 8 support 1080p 50 Hz , it show the Common LVDS resolution configuration parameters which need to meet the requiremnet. Best regards, Geekworm)
10:06, 16 January 2019 Admin talk contribs posted a new comment on X730 (Hello sir, The X730 board is not suggested to use with X820 board. As it is hard to solve the power problem, and also it is not suitable to install in X820 case, Best regards, Cindy/Geekworm)
10:04, 16 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, It depends on what battery capacity you use and the battery quality, we suggest that you use big capacity batteries,thank you. Best regards, Cindy)
17:41, 15 January 2019 82.208.98.238 talk posted a new comment on Smart Fan and Power Expansion Board (Thanks for script! It works at RPI b3+.)
16:33, 15 January 2019 105.159.214.218 talk posted a new comment on Raspi UPS HAT Board (how long battery last?)
22:09, 14 January 2019 213.138.74.78 talk posted a new comment on LVDS To HDMI Adapter Board (Hi, Thanks for the quick comment. What can be said about the resolution of 1080p 50 Hz - on page 7 in paragraph 6.3 in the second row of the table - should this mode be supported by this controller? Best regards.)
18:14, 14 January 2019 189.33.89.146 talk posted a new comment on X730 (I want to have the x820 board and metal case. I also want to use this X730 board for the safe shutdown, is it going to fit in the x820 metal case? How should I connect the x820 board to the x730?)
11:53, 14 January 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hello sir, Thanks for your feeback. We do not have other LVDS to HDMI device with a resolution of 576i and 576p. 50 Hz. Best regards, Geekworm)
11:43, 14 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, What can we help you? Best regards, Geekworm)
11:28, 14 January 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, We can not guarantee the compatibility,maybe you can google to find some information.The EXP GDC is the diy product, we list the detail information at the page above. Best regards, Geekworm)
02:14, 14 January 2019 178.155.5.68 talk posted a new comment on LVDS To HDMI Adapter Board (I have experience using this device. There is some discrepancy in the File description: S-LH1080P-AUDIO-V17-Spec-20180504-1.pdf and the actual operation of the device: namely, on page 7 in clause 6.3 the supported mode is 1080p 50Hz (1920 * 1080 50Hz?)...)
19:19, 13 January 2019 95.192.200.27 talk posted a new comment on Raspi UPS HAT Board (I've written a nodejs module to communicate with the MAX17048 chip that monitors battery charge on this board. See https://www.npmjs.com/package/max17048)
14:39, 12 January 2019 189.204.182.61 talk posted a new comment on EXP GDC (amd radeon r7 240)
14:37, 12 January 2019 189.204.182.61 talk posted a new comment on EXP GDC (hi asus k52jt is work is a)
14:19, 5 January 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello, We have updated your questions to our wiki FAQ above, please check the details, thanks very much! Best regards, Cindy/Geekworm)
12:59, 5 January 2019 Admin talk contribs deleted comment #123 on Robot Expansion Board
12:07, 5 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Thanks for your message, we suggest that you can contact us by email: support@geekworm.com to confirm more details. 1.Please tell us what battery do you use for the UPS. 2.Please test the output voltage of ups hat by the GPIO PIN. 3.Please also...)
11:57, 5 January 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello sir, You can run a servo and a dc motor at the same time, but the servo pwm support only one output. If any more questions, please contact us by email. Best regards, Cindy/Geekworm)
08:58, 5 January 2019 Admin talk contribs posted a new comment on X820 (Hello, Sorry, the Power button of X820 board do not support safe shutdown or orderly shutdown, they will a power supply extension board will be release in the future to control safe shutowon of the Raspberry Pi. Hope you can pay attention to our offic...)
08:54, 5 January 2019 Admin talk contribs posted a new comment on X5000K (Hello, We check the page, it is normal, you can refer to here: http://www.suptronics.com/miniPCkits/x5000k-hardware.html If still any questions, please contact us by email: support@geekworm.com. Best regards, Cindy/Geekworm)
03:46, 5 January 2019 173.71.158.18 talk posted a new comment on X820 (how do you set up the power button to do an orderly shutdown of the Pi?)
01:31, 5 January 2019 104.218.69.112 talk posted a new comment on Robot Expansion Board (can you run a servo and a dc motor at the same time? or do the servo pwm commands change the signal on all outputs?)
22:13, 4 January 2019 84.208.232.249 talk posted a new comment on X5000K (SupTronics webpage no longer have the hardware installation instructions.)
20:07, 4 January 2019 87.58.163.237 talk posted a new comment on Raspi UPS HAT Board (Hi, I have some problems with undervoltage when my RPI 3+ is powered by the UPS HAT. This occurs both while the power supply (PSU) via micro-USB is connected or not. I have tried to power the PRI directly from the PSU, and no undervoltage here. The HAT...)
11:11, 3 January 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, Would you mind tell us where do you order this board? What battery do you use? Please check if the red cable and black cable of the battery 2.0 port in the right place, and also refer to the photo above. If any questions, please contact us b...)
00:19, 3 January 2019 86.27.22.183 talk posted a new comment on Raspi UPS HAT Board (Hi, can the battery percentages for led lights be modified? My boards lights are always all on unless charging. They do not behave as in your battery capacity table. Reading from ic2 works fine.)
14:49, 2 January 2019 Admin talk contribs posted a new comment on 7 inch HDMI LCD (H) (Hello sir, In the manual, it is clear that: 1.When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free 2.When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free I tihink...)
14:31, 2 January 2019 Admin talk contribs posted a new comment on RPi UPSPack (Hello sir， Sorry, we do not have the datasheet, these led on the board has power led and 4 battery voltage led, they marked clearly on the photo above, please have a look. Best regards, Cindy/Geekworm)
05:07, 31 December 2018 88.181.156.18 talk posted a new comment on RPi UPSPack (Hi, I want to export all leds, do you have a datasheet about these leds? (power/charge/level batt) Best regards)
05:40, 30 December 2018 75.140.125.94 talk posted a new comment on 7 inch HDMI LCD (H) (This appears to be w wonderfully thought out design! I ordered one. Suggest perhaps editing website for minor spelling and grammar errors, but the information is clear enough as it is. Note conflicting information, features on wiki says one touch, ma...)
17:34, 29 December 2018 Admin talk contribs deleted comment #109 on X850
17:34, 29 December 2018 Admin talk contribs posted a new comment on X850 (Hello, Thanks for your feeback and advice, we will try to improve it later. Actually it has no feeback that the screws will cause the electrical short problem.Please don't worry! Best regards, Geekworm)
17:33, 29 December 2018 Admin talk contribs posted a new comment on X850 (Hello, Thanks for your feeback and advice, we will try to improve it later. Actually it has no feeback that the screws will cause the electrical short problem.Please don't worry! Best regards, Geekworm)
21:55, 28 December 2018 24.63.194.159 talk posted a new comment on X850 (I'd suggest you replace two of the screws with nylon ones. The outer part of the screw came close to touching parts of the SSD I used and I was concerned about a possible electrical short. Fortunately I had some nylon screws that fit. replaced your scr...)
19:08, 27 December 2018 Admin talk contribs posted a new comment on LHT00SU1 Virtual Oscilloscope SKU:412961 (Thanks!)
12:52, 26 December 2018 81.174.250.193 talk posted a new comment on LHT00SU1 Virtual Oscilloscope SKU:412961 (for English edition of the USBee AX software you can download a copy https://usbee-ax-test-pod.software.informer.com/download/ Also www.archive.org is useful for obtaining the final versions from archived copies of www.usbee.com Sigroks pulseview can...)
09:25, 25 December 2018 Admin talk contribs posted a new comment on EXP GDC (Hello sir, If your laptop has an Express Card connector, then you need to choose EXPRESSCARD verison EXP GDC, we are so sorry for your laptop model, we do not test it, we can can not guarantee. For the graphic card, please refer to: Recommended Graphi...)
22:48, 24 December 2018 104.219.184.109 talk posted a new comment on Stepper/Motor/Servo Robot Expansion Board SKU:418460 (Hello, I am also having the same problem. I am running ServoTest.py and it sits there. Servos do nothing.)
20:41, 24 December 2018 178.42.70.104 talk posted a new comment on EXP GDC (Good morning! I have a Fujitsu P702 Laptop. Will this interface work with it? It has an Express Card connector. An additional question: Will the Quadro K600 graphics card work with this interface?)
09:51, 21 December 2018 Admin talk contribs posted a new comment on RPi UPSPack (Hello sir, We get your email, and we help you check it, the capacitor is MLCC 47uF, package1206 47uF, and Withstand voltage 16V+ is ok. Best regards, Geekworm)
09:24, 21 December 2018 Admin talk contribs posted a new comment on X830 (Hello sir, You can access the files in the 3.5HDD from the Raspberry Pi, and also you can use it as an external drive. Best regards, Cindy/Geekworm)
20:13, 20 December 2018 213.22.236.225 talk posted a new comment on X830 (That might be a stupid question, I am sorry. But can you access the files in the 3.5HDD from the Raspberry Pi or only use it as an external drive ?)
12:07, 20 December 2018 93.206.139.30 talk posted a new comment on LVDS To HDMI Adapter Board (It is omnidirectional. If you need HDMI to LVDS, you will need an LCD driver board, which is plentiful outside, such as on eBay, Amazon, or AliExpress. You can simply type in Raspberry Pi LCD and you would get a display that's fully compatible with the Pi)
11:39, 20 December 2018 Admin talk contribs posted a new comment on Stepper/Motor/Servo Robot Expansion Board SKU:418460 (Hello sir, It has been tested no problem, as the steering engine voltage is 5V, the current should be around 200mA. We suggest that you can change the 996, 995 series steering engine to have a try. Thank you! Best regards, Cindy/Geekworm)
10:36, 20 December 2018 Admin talk contribs posted a new comment on RPi UPSPack (Hello sir, Sorry, we can not provide the schematic, all the information are on the wiki page, please check. Best regards, Cindy/Geekworm)
08:05, 20 December 2018 172.113.101.48 talk posted a new comment on Stepper/Motor/Servo Robot Expansion Board SKU:418460 (Has anyone been able to test PWM servo motor on this boards? I tried the ServoTest.py in Raspi-MotorHAT.zip but it not seem working.)
20:02, 19 December 2018 87.241.31.125 talk posted a new comment on RPi UPSPack (A board has failed, it is possible to have the schematic for the repair. paolo.carecci@gmail.com)
16:05, 19 December 2018 Admin talk contribs posted a new comment on Stepper/Motor/Servo Robot Expansion Board SKU:418460 (Hi, Sorry, we can not confirm your problem. If you still have problem, it is better to contact us by email: support@geekworm.com. Best regards, Geekworm)
14:55, 17 December 2018 Admin talk contribs posted a new comment on 10.1 inch LCD (2560x1600) (Hello sir, Please refer to above Document: File:LR1012K01-EDP.PDF. Best regards, Geekworm/Cindy)
14:53, 17 December 2018 Admin talk contribs posted a new comment on Smart Fan and Power Expansion Board (Hello sir, It is not tested on libreelec. We suggest that you can do a test, thank you very much! Best regards, Geekworm)
09:30, 17 December 2018 Admin talk contribs posted a new comment on EXP GDC (Hello sir, Thanks for your advice, we get your feeback and will report it to the engineer, thank you! Best regards, Geekworm)
04:50, 17 December 2018 92.196.65.50 talk posted a new comment on 10.1 inch LCD (2560x1600) (What is the pin layout of the power socket?)
00:20, 16 December 2018 86.58.87.224 talk posted a new comment on Smart Fan and Power Expansion Board (can add this to libreelec??)
05:33, 15 December 2018 84.13.34.227 talk posted a new comment on EXP GDC (hello. this product is probably not aimed at people like me, but it could be extremely helpful. I do 3D rendering work that requires a lot of GPU power. so is there any reason I would not be able to use this product (the 9.5 version with m.2) on a desk...)
09:27, 14 December 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, We do not test it, so we can not confirm anything, hope to get your understanding! Maybe you can do a test. Best regards, Geekworm)
20:55, 13 December 2018 134.2.118.242 talk posted a new comment on Raspi UPS HAT Board (What if I first add the UPS HAT board on the Raspberry Pi Zero W and on top of the UPS hat the Hifiberry mini hat?)
11:32, 13 December 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, Sorry, the UPS HAT board only can power the Raspberry Pi zero W by weld the GPIO pin header on it, but if you add the Hifiberry mini hat on it, then it will not possible to add the UPS HAT board by GPIO PIN, hope to get your understanding! B...)
05:46, 13 December 2018 2.205.173.126 talk posted a new comment on Raspi UPS HAT Board (Hi, I would like to power my Raspi Zero W with a Hifiberry mini hat (https://www.hifiberry.com/shop/boards/miniamp/ using the geekworm UPS. Does it work with a Raspi Zero W?)
08:51, 11 December 2018 Admin talk contribs posted a new comment on X820 (Hello, We suggest you use the high quality and big brand SSD OR HDD. As the low quality SSD and HDD may not be recognized after installation, hope to get your understanding! Best regards, Cindy/Geekworm)
20:14, 10 December 2018 46.91.217.197 talk posted a new comment on X820 (Hello, WHich SSD AND HDD do you recommenr??)
15:33, 10 December 2018 Admin talk contribs posted a new comment on X820 (Hello, Sorry, there is no such a UPS expansion board to power the Pi and the drive , the best way is to power the whole set with DC 5V 4A POWER SUPPLY. if any more questions, please comtact us by email. Best regards, Cindy)
06:04, 8 December 2018 146.60.136.192 talk posted a new comment on X820 (Is there a UPS expansion board that will keep the Pi and the drive powered?)
10:26, 7 December 2018 Admin talk contribs posted a new comment on X830 (Hello friend, Yes. this 19V 3.42A 5.5x2.5mm AC power supply is ok for X830 board. X830 Power supply: 14V-40V wide range voltage input, and the current is greater or equal to 2A or 3A ia ok, please note. Best regards, Geekworm)
02:09, 7 December 2018 82.19.220.9 talk posted a new comment on X830 (Is this power supply ok for x830: https://www.amazon.co.uk/ARyee-5-5x2-5mm-Adapter-Charger-Satellite/dp/B079NDS4Q2)
10:20, 6 December 2018 Admin talk contribs posted a new comment on X820 (Hello sir, You have the X820 v3.0 version expsnaion board, right? And the 5V OUT USB port is a 5V 2A POWER output for other device, it maybe ok to connect other device, but the output power is only 5v 2a, maybe your device drives too much power. If ang...)
22:55, 5 December 2018 189.177.114.220 talk posted a new comment on X820 (Can I use the 5V USB power output for anything? I am using GPIO pins to power my RPI. I tried plugging a cable into the USB 5V for something else yesterday while my PI was running, and the entire unit shut down. I know my USB cable and the unit I plugg...)
12:14, 3 December 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello， We are so sorry, it seems that there is no way know if raspberry is powered by the battery, we will do a research about it, thank you! Best regards, Geekworm)
11:31, 3 December 2018 Admin talk contribs posted a new comment on X820 (Hello, Sorry, the X820 v3.0 board can not be used while plugged on Raspberry pi and on a Mac at the same time, you can use the only X820 v3.0 board with a 2.5 inch SATA HDD or SSD on it with the blue USB cable to connect on Mac as a mobile hard disk, h...)
21:17, 1 December 2018 37.169.37.41 talk posted a new comment on Raspi UPS HAT Board (Hi, is there a way to know if the raspberry is powered by the battery, or external power ? Or, in other way, to know if the external power fails ?)
18:58, 1 December 2018 78.202.166.147 talk posted a new comment on X820 (How can I use the X820 expansion board plugged on Raspberry Pi and intermittently on a Mac under OSX? The specs indicates "Quick file transfer with high-speed USB 3.0 connectivity from a PC or a Mac". But an extended web search do not show it is possib...)
10:18, 30 November 2018 Admin talk contribs deleted comment #71 on EXP GDC
10:18, 30 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello, Could it work with its own monitor? If you use the AMD series card,it must to connect with the external monitor to use. If you use N series card which over GTS450, and your laptop own Intel Core graphics ,and use the EGPU software to set,then...)
10:17, 30 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello, Sorry, we do not test it on Lenovo Thinkpad L412 with Intel Core i3 M370 , as the EXP GDC laptop docking stations is a DIY product, we can not guarantee the compatibility for each laptop, hope to get your understanding! Maybe you can google for...)
10:16, 30 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello, Sorry, we do not test it on HP Probook 430 G5, as the EXP GDC laptop docking stations is a DIY product, we can not guarantee the compatibility for each laptop, hope to get your understanding! Maybe you can google for some more reference, thank...)
10:09, 30 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello, The list of recommended graphics card: GTX650 GTX660 GTX670 GTX750 GTX760 GTX950 GTX960 GTX970 GTX980 GTX1060 GTX1070 GTX1080 And for other graphics cards, may be they can also be used, but the compatibility and performance are not as good as th...)
10:08, 30 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello sir, Sorry, we can not find your laptop model in the support list, as the EXP GDC laptop docking stations is a DIY product, we can not guarantee the compatibility for each laptop, hope to get your understanding! And also please refer to the Recom...)
10:02, 30 November 2018 Admin talk contribs posted a new comment on X400 (Hello, It is hard to confirm the problem here, please send us the details include the order number and item link and the set up deatils to our email: support@geekworm.com, we will help you about this, thank you! Best regards, Geekworm)
20:11, 29 November 2018 64.20.38.156 talk posted a new comment on X400 (I am unable to get sound from the Speaker terminals. I followed the setup instructions. The amp is getting power (it gets plenty warm) and it works via the headphone jack, but with two 4 ohm 20 W speakers hooked to the Speaker terminals there is no sou...)
08:38, 27 November 2018 70.81.137.39 talk posted a new comment on EXP GDC (Hello, i am thinking about buying that product (the mini pcie version) for a msi gt60 2qd (my actual graphic card is a gtx970m), to play in vr. If i put a desktop gtx 980 with like 6gb of ram, will that systeme work great with an oculus rift? Or there...)
02:59, 25 November 2018 Admin talk contribs posted a new comment on X830 (Hi, This power supply supply 19V Max 2A, so is 19*2=38W; Maybe it's enough power the TS100. and we don't test it in TS100; By the way, we are selling TS100 also: https://www.aliexpress.com/store/product/Mini-TS100-OLED-Programable-Smart-Adjustable-Sol...)
02:50, 25 November 2018 Admin talk contribs posted a new comment on X820 (Hello sir, We will release a new power manage expansion board(X720) with safe shutdown, with remote wake up etc. function soon. Geekworm)
22:29, 24 November 2018 87.11.7.51 talk posted a new comment on X830 (Is it compatible with the soldering TS100? It accept a range from 12v to 24v, at 19v it needs 40w. https://www.banggood.com/MINI-TS100-Digital-OLED-Programmable-Interface-DC-5525-Soldering-Iron-Station-Built-in-STM32-Chip-p-984214.html?rmmds=search Thanks)
19:44, 23 November 2018 Admin talk contribs posted a new comment on X830 (Hello, This is the behavior of mechanical hard drives. In general, hard disk hibernation is to extend the life of the hard drive or other reasons. I suggest you check your hard drive specification Harry / Geekworm)
01:52, 23 November 2018 47.147.196.190 talk posted a new comment on X830 (When the drive isn't used for more than a couple of minutes, the drive spins down automatically Is there a way to disable this? I wish this were controllable via the OS, or at least via a jumper.)
14:22, 21 November 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Sir, we advise that you change the battery, you can use the 3.7v 18650 battery. Geekworm)
12:40, 20 November 2018 Admin talk contribs posted a new comment on X400 (Hello friend, We are no sure about this, maybe you can have a try. If any questions, please contact us by email. Best regards, Geekworm)
12:39, 20 November 2018 Admin talk contribs posted a new comment on X400 (Hello friend, The X400 need to use a DC Jack: 5.5x2.5mm port power supply, we have a recommedned power supply you can check what it look like: https://geekworm.com/products/dc-5-5x2-5mm-19v-2a-eu-us-plug-power-supply-for-raspberry-pi-x830-x400-expansio...)
12:25, 20 November 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, All the information is on this wiki page. Sorry, there is no schematics of this card provided, hope to get your understanding! Best regards, Geekworm)
12:24, 20 November 2018 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, If you want your Raspberry Pi to be able to start automatically when you have an external power supply or battery, rather than manually switch on power. You can use this USB to 2 Mirco USB Cable, USB connect charger, one Micro USB connect Ra...)
15:55, 19 November 2018 Admin talk contribs posted a new comment on X830 (Hello friend, Sorry, it may can not control the led indicator of HDD, BUT you can control the lED of the power button by pull out the white cable. If any more problem, please contact us by email. Best regards, Geekworm)
15:52, 19 November 2018 Admin talk contribs posted a new comment on X830 (Hello friend, What do you mean by graceful shutdowm? Is it safe shutdown? If yes, sorry, the power button of the case do not support safe shutdon. Maybe there will be an extension board to realize the safeshutdown function. Best regards, Geekworm)
15:48, 19 November 2018 Admin talk contribs posted a new comment on X830 (Hello friend, The power supply will not inlcude in the metal case. There is a 19v 2a power supply for this X830 board, if you need you can order them at geewkorm official website: geekworm.com thank you! Best regards, Geekworm)
16:09, 15 November 2018 Admin talk contribs posted a new comment on X820 (Hello sir, Thanks for all your feedback, we get your suggestions now and will consider to add the GPIO access on the top cover of the case, but it will make the case look like not so beautiful. For the safe shutdown problem, sorry, the power button do...)
22:37, 14 November 2018 64.124.76.250 talk posted a new comment on X830 (Where do you buy the power supply, or is it included with the purchase of the box?)
21:38, 14 November 2018 187.214.102.20 talk posted a new comment on X820 (I like the case, but I think there could be some improvements. Here is my list. I have checked these items with others, and they say they would be likely to buy the case if some or all of these were implemented: - make it taller so there isn't an issue...)
18:22, 14 November 2018 2.236.54.226 talk posted a new comment on X830 (How does work the power button? Does it allow graceful shutdown?)
16:26, 14 November 2018 49.146.225.95 talk posted a new comment on EXP GDC (good day can you please guide me and i lke to connect exp gdc and what video card you recommend my laptop is acer aspire v3-571 thanks -michael calonzo)
05:06, 13 November 2018 76.31.90.110 talk posted a new comment on Raspi UPS HAT Board (Where can I reach the schematics of this card?)
21:57, 11 November 2018 176.139.101.12 talk posted a new comment on EXP GDC (Hello, I have a HP Probook 430 G5(version NGFF) and I would like to know if this model is compatible with EXP GDC because I do not find it in the whitelist or in the blacklist. Thank you)
06:54, 11 November 2018 187.214.102.20 talk posted a new comment on X820 (For a future version, please make it possible to control Raspberry PI for a clean shutdown command when the power button is pushed, similar to how it works with a PC or laptop. It should be easy to add a connection to the GPIO and then a very small scr...)
23:48, 9 November 2018 84.75.30.196 talk posted a new comment on X820 (For auto power ON, add a 1uF capacitor between the red wire (+) and the black wire plugged on the button. Respect the polarity of your capacitor if necessary (tantalum ou electrolytic).)
11:30, 9 November 2018 114.125.103.182 talk posted a new comment on EXP GDC (Is Lenovo Thinkpad L412 with Intel Core i3 M370 can use EXP GDC ? I don't see on Support Device nor Blacklist Device there .)
11:14, 7 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello sir, For the black screen problem, please try these and use exclusive method to find out and solve the problem. 1. Try it like the sleep way.Do not connect the cable of graphic card, start up your laptop, go to sleep when you go in the system, th...)
11:13, 7 November 2018 Admin talk contribs posted a new comment on EXP GDC (Hello sir, The AMD graphic card is not recommended, as it may has many problem. The list of recommended graphics card: GTX650 GTX660 GTX670 GTX750 GTX760 GTX950 GTX960 GTX970 GTX980 GTX1060 GTX1070 GTX1080 And for other graphics cards, may be they...)
10:59, 7 November 2018 Admin talk contribs posted a new comment on X820 (Hello sir, Please contact us by support@geekworm.com to help you figure out the problem, thank you! It is better to attach some video or photos. Best regards, Geekworm)
10:58, 7 November 2018 Admin talk contribs posted a new comment on X820 (Hello, Thanks for all you feedback,it was found out that there a little capacitor on the X820 board to be changed, then it will slove the problem. If you need to know which capacitor need to be change, please send email to : support@geekworm.com. The...)
10:56, 7 November 2018 Admin talk contribs posted a new comment on X820 (Hello, Thanks for all you feedback,it was found out that there a little capacitor on the X820 board to be changed, then it will slove the problem. The auto on problem will be solved soon, when the updated products released, we will update information....)
12:59, 5 November 2018 24.107.152.9 talk posted a new comment on Raspi UPS HAT Board (What modification is necessary to make the board be "always on". Another way to say, what modification will bypass the on/off switch?)
21:52, 4 November 2018 86.212.178.53 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Could you describe how to do the easy method without using Windows? I tried 7za and that extracted an img file but using dd to put that on /dev/sdx leads to there being no partition table on the sd card. What do all these "may contain malware" windows...)
19:20, 4 November 2018 120.18.148.234 talk posted a new comment on X6000K (Testing your X6000 with your blu-ray player. More tests. As I mentioned in the earlier post, your blu-ray player must have hdmi audio set to "PCM" (or "LPCM") NOT "bitstream" if you want to have 7.1 channel audio from the 3.5mm analogue output. As I m...)
12:37, 4 November 2018 120.17.210.30 talk posted a new comment on X6000K (I have received the X6000, and tested it. I will give a summary then details. Even though I gave a detailed description of the X6000's EP91A6S processor, the datasheet for the EP91A6S there was not enough information about the HDR signals at the IIS bu...)
02:14, 2 November 2018 82.235.134.111 talk posted a new comment on X820 (Which colored cable should I pull out in order to disable the blue LED on the big power button? Thanks~)
19:42, 1 November 2018 86.84.78.245 talk posted a new comment on X820 (I also suffer from the same problem, would like to have the PI running all the time. Also does not boot up automatically after a reboot (I need to push the power button first). Any solutions appreciated!)
18:36, 30 October 2018 178.117.89.32 talk posted a new comment on X830 (Is it possible to control the led light, both for the button on the case and for the led on hdd activity?)
08:35, 29 October 2018 184.166.244.15 talk posted a new comment on Stepper/Motor/Servo Robot Expansion Board SKU:418460 (In Step 3 it looks like the directory name is wrong. Check via ls command and cd to correct directory to complete instructions.)
19:43, 28 October 2018 88.114.0.180 talk posted a new comment on 2.2 inch TFT Display SKU:398437 (Q1: Is display brightness PWM controllable, what GPIO pin? Q2: Is it possible to use this display with Python programs fully separate (on device "/dev/fb1") without blocking desktop screen on HDMI-output?)
11:02, 26 October 2018 209.58.142.155 talk posted a new comment on Smart Fan and Power Expansion Board (#!/usr/bin/python # MyRPi.ca script - ocs11@hotmail.com # 2018-10-01 # Python script that uses multiple sources to determine the CPU and enclosure temperature # and adjust the fan speed automatically # Load system libraries import RPi.GPIO as GPIO #...)
04:01, 26 October 2018 71.47.162.47 talk posted a new comment on Raspi UPS HAT Board (I am trying to migrate my python2 app to python3 and got the following error message when running with python3. How can I fix this to work? import raspiupshat ImportError: /home/pi/build/raspiupshat.so: undefined symbol: Py_InitModule4)
01:23, 21 October 2018 120.17.55.66 talk posted a new comment on X6000K (I actually purchased the X6000 and look forward to using it. I will exercise caution here on describing the capabilities because I have not received it yet and have not done experiments with it. I will give my summary first and my reasoning. Summary:...)
07:41, 19 October 2018 189.129.111.42 talk posted a new comment on EXP GDC (La tarjeta grafica AMD RX 570 y la AMD RX 580 es compatible con EXP GDC?)
06:51, 19 October 2018 23.125.39.69 talk posted a new comment on X400 (I just received my X400 board, but the power adapter I planned to use with it is too large. What is the correct connector for making a 12 volt connection to the X400? Do I understand correctly that the 12 volt connection will power the entire system?...)
01:30, 19 October 2018 120.17.202.204 talk posted a new comment on X6000K (I am very close to purchasing the board from a vendor. I have researched further on the EP91A6S IC with particular attention to the block diagram. Once the HDMI input signal is handled and 'passed' by the EP91A6S, it goes to two paths, the HDMI outpu...)
18:57, 18 October 2018 120.17.208.0 talk posted a new comment on X6000K (Dear Cindy or other authorised person, Thank you for your previous answer. Goint back to the RPi's GPIO ports. Does the X6000 use any of the GPIO ports (1-40) to control the X6000? Note I am not talking about the +5V and gnd (pins 1,3). Thank you,...)
17:52, 18 October 2018 Admin talk contribs posted a new comment on X6000K (Hello friend, Thanks for your questions, we ask for some feedback, it is possible to use the blu-ray player with this X6000-7.1ch expansion board, but please note the Power-on sequence must be: 1. Television 2.X6000-7.1ch, 3. Blue-ray player. Please no...)
21:56, 17 October 2018 120.17.208.130 talk posted a new comment on X6000K (I had a look at the EP91A6S IC used in the X6000 board at http://www.epmi.com.tw/pro_d.php?pk=151. According to the datasheet, it supports HD Audio. Instead of using the hdmi from the RPi to the hdmi input of the X6000, can I instead connect the hdm...)
22:59, 16 October 2018 178.119.11.156 talk posted a new comment on LVDS To HDMI Adapter Board (Can Someone make this article idiot proof? I'm looking for a board to power a screen. So it should be hdmi to LDVS. Or is it omnidirectional?)
20:32, 15 October 2018 23.125.39.69 talk posted a new comment on X400 (So, given that I want to use this unit to drive a pair of speakers, I understand that I want to use the jumpers to turn-off the headphone and RCA jack systems. Is that correct?)
19:20, 15 October 2018 Admin talk contribs posted a new comment on X400 (Hello sir, Sorry, this x400 board does not support Dolby 7.1 or Dolby True HD, DTS 7.1 or DTS-HD Master Audio. Best regards, Geekworm)
14:37, 15 October 2018 120.17.171.230 talk posted a new comment on X6000K (How does one use a USB blu-ray drive connected to the RPi in order to play blu-ray movies on the RPi utilizing the X6000. Thank you, Anthony of Sydney Australia)
20:57, 14 October 2018 120.17.126.146 talk posted a new comment on X400 (It says that this board supports full HD audio. Does it support Dolby 7.1 or Dolby True HD, DTS 7.1 or DTS-HD Master Audio? Thank you)
18:43, 14 October 2018 178.117.190.46 talk posted a new comment on Raspi UPS HAT Board (I installed the UPS HAT about 9 months ago and I see decreasing the voltage/percentage week by week? Would this be a problem of the battery or rather the hardware/algorithm? Thanks for your help...)
10:08, 10 October 2018 27.38.254.12 talk posted a new comment on X820 (No support you said.)
09:30, 8 October 2018 50.4.39.247 talk posted a new comment on X820 (How can I have the board(s) auto power on after a power fail? Switching the header from “auto off” to “auto on” does not seem to work.)
01:20, 5 October 2018 120.229.48.142 talk posted a new comment on EXP GDC (we are on the China National Day vacation, and we will reply you soon.)
03:19, 1 October 2018 176.154.149.44 talk posted a new comment on EXP GDC (hello, I'm contacting you about a configuration problem. Acer Aspire 5742g PEW71, EXP GDC V8.5c and 12v external power supply. the pc reboots indefinitely with a black screen. I would like to know the adapted configuration. Thank you)
20:38, 5 September 2018 27.38.246.23 talk posted a new comment on SUPERPi CASE U ([https://www.aliexpress.com/store/product/Retroflag-SUPERPi-Case-NESPi-Console-UCase-w-USB-Controller-Gamepad-Heatsinks-Fan-Kit-for-Raspberry-Pi/1048722_32918240273.html Here])
20:36, 5 September 2018 27.38.246.23 talk posted a new comment on SUPERPi CASE J ([https://www.aliexpress.com/store/product/Retroflag-SUPERPi-Case-NESPi-Console-JCase-w-USB-Controller-Gamepad-Heatsinks-Fan-Kit-for-Raspberry-Pi/1048722_32920543457.html Here])
15:12, 1 September 2018 Admin talk contribs deleted comment #1 on X230
15:12, 1 September 2018 Admin talk contribs posted a new comment on X230 ([https://geekworm.aliexpress.com/ Geekworm Official Store])
15:12, 1 September 2018 Admin talk contribs deleted comment #4 on X230
15:06, 1 September 2018 27.38.246.5 talk posted a new comment on X230 (https://geekworm.aliexpress.com/)
15:02, 1 September 2018 27.38.246.5 talk deleted comment #3 on X230
15:02, 1 September 2018 27.38.246.5 talk posted a new comment on X230 (X230#comment-1)
15:01, 1 September 2018 27.38.246.5 talk deleted comment #2 on X230
14:47, 1 September 2018 27.38.246.5 talk posted a new comment on X230 (Nice)
14:46, 1 September 2018 27.38.246.5 talk posted a new comment on X230 (Good)

(newest | oldest) View (newer 500 | older 500) (20 | 50 | 100 | 250 | 500)

Comments log

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

In other languages

WIKI