Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 10:42, 24 August 2022 Lisa talk contribs posted a new comment on PiKVM (Hi，It does not support reverse power)
  • 01:18, 24 August 2022 46.135.84.179 talk posted a new comment on PiKVM (Does the X630 HDMI to CSI bridge has HDMI backpower workaround so it can be used with KVM switch?)
  • 15:36, 22 August 2022 Lisa talk contribs posted a new comment on UPS3 (Hi， please follow herehttps://wiki.geekworm.com/UPS3#FAQ to explain to check the question)
  • 00:43, 20 August 2022 24.48.116.189 talk posted a new comment on UPS3 (After installing the UPS3 and some testing, it seems that the Raspberry pi 4 will not boot up if it's powered down (poweroff) and the power is back, except if the battery is dead or removed in the mean time. Is the behavior correct? Based on the description, as soon as power is back, the Pi shoud boot up normally)
  • 11:13, 19 August 2022 Lisa talk contribs posted a new comment on X735 Hardware (Hi, The x735 cannot be connected to the battery, please refer to the X708 ups board)
  • 18:50, 18 August 2022 80.169.225.194 talk posted a new comment on X735 Hardware (Hi. I want to use it with a 12V battery and a ignition contact. 3 wires: 12V, GND, and ignition (signal). when the ignition is on (12V), I want to start the raspberry. The ignition will remain on (12V). When the ignition is off (0V), I want to safe shut down the rasberry. Can this be done with your X735 board? thanks)
  • 14:01, 18 August 2022 101.100.139.149 talk posted a new comment on NASPi Gemini (Figured it out :-) Changing the power management of the HDD from 128 to 127 fixed it: hdparm -B 127 -S 60 /dev/sdb)
  • 11:18, 17 August 2022 Lisa talk contribs posted a new comment on X832 (Hello， Please refer to the instructions here to test X832 + HDD： How to check the X820)
  • 02:27, 17 August 2022 91.101.118.93 talk posted a new comment on X832 (Hi, I have X832 v1.2 3.5" + x735 v3.0 Raspberry Pi 4 8GB. All seems to be running, butHHD is not recognized. I have installed Openmediavault formatted HDD as ext4. Can't list the HDD in linux either. Tried several different HDD'S I've followed the setup video and it seems right but not showing HDD. Please help if I am doing something wrong Thanks Peter)
  • 11:28, 16 August 2022 Lisa talk contribs posted a new comment on X880 (Hello， Sorry，X880 does not support software safe shutdown.)
  • 02:38, 13 August 2022 172.58.79.161 talk posted a new comment on X880 (Is there a safe way to shut down? I know the idea of a NAS is to he on 24/7 but sometimes you just need to turn it off. I use OMV on Debian and I tried sudo shutdown -r now and it goes the the shutdown process but the drives never power down even after 10 minutes. It feels wrong to just pull the plug on a spinning drive.) Tags: Mobile web edit, Mobile edit
  • 11:11, 11 August 2022 Lisa talk contribs posted a new comment on CM4 Stick (Hi， cm4 does not need a separate dts file, the official system is fine, because the interface does not need to be configured separately, you can operate the default mode)
  • 10:59, 11 August 2022 Lisa talk contribs posted a new comment on NASPi Gemini (Hi， X882 does not have sleep mode, because many users request to turn off sleep mode so that the NAS can run stably.)
  • 10:45, 11 August 2022 Lisa talk contribs posted a new comment on LVDS Adapter (Hi， It is a 4pin audio interface, please use the 4Pin cable)
  • 05:18, 11 August 2022 101.100.139.149 talk posted a new comment on NASPi Gemini (Hi there, I have a question - my hard drive never spins down, although it's set up to do so. Is the X882 board preventing hard drive from sleeping?)
  • 00:59, 10 August 2022 99.149.236.97 talk posted a new comment on LVDS Adapter (What kind of cable connects to the audio interface?)
  • 10:42, 9 August 2022 Lisa talk contribs posted a new comment on X880 (Please use the same type of hard drive,HDD+HDD or SSD+SSD； an error will be reported when using SSD+HDD. If only 3.5inch disk of 8TB Toshiba is connected, do not connect other hard drives, can it boot normally？ PS：It is recommended to use an SD card to install the system.)
  • 09:10, 9 August 2022 217.155.46.70 talk posted a new comment on CM4 Stick (Is there a dts file for the CM4 stick?) Tags: Mobile web edit, Mobile edit
  • 08:15, 9 August 2022 45.131.192.74 talk posted a new comment on X880 (I have connected two disks, first one a 2,5 480GB SSD in which I've installed Raspberry Pi OS Lite (32-bit) and second one 3,5 disk of 8TB Toshiba N300 NAS, I'm supplying a power of DC 12v 5A charger. If only connect the first one boots okay, the problem comes when I connect both disks, the Pi doesn't works not boot. I was thinking if is there a limitation on the size of the disk? I'm using a CLEAR RAID. Any suggestion?)
  • 15:18, 8 August 2022 Lisa talk contribs posted a new comment on X880 (Hello， Did you test with only one hard drive（3,5 disk of 8TB Toshiba N300 NAS） connected? What power supply are you using?)
  • 13:11, 8 August 2022 45.131.192.238 talk posted a new comment on X880 (Hi, I've a problem connecting a 3,5 disk of 8TB Toshiba N300 NAS, the X880 blue led flashes but not boot the raspberry pi I only see this error in screen: EXT4-fs error (device sda2): __ext4_find_entry:1614: inode #1426: comm systemd-udevd: reading directory lblock 0 I have other 480GB SSD connected and this works properly I only have problem with the other. Any idea why it doesn't boot with that drive?)
  • 09:57, 6 August 2022 Lisa talk contribs posted a new comment on X715 (Hi， X715 not support Iqaudio Amp.)
  • 11:52, 5 August 2022 108.162.176.151 talk posted a new comment on X715 (How can I use this board with Iqaudio Amp which also has a DC power input (6-18V)? Where should I connect the power plug to?)
  • 10:09, 3 August 2022 Lisa talk contribs posted a new comment on NASPi (Hello， You can also use the spare acrylic sheet to replace the front panel of the case to reduce interference to WIFI)
  • 18:27, 2 August 2022 176.161.224.230 talk posted a new comment on NASPi (I'm using an usbc cable to power it up, connected to the naspi as specified.)
  • 18:26, 2 August 2022 176.161.224.230 talk posted a new comment on NASPi (THis is the error: Aug 02 11:17:33 raspberrypi udisksd[496]: Acquired the name org.freedesktop.UDisks2 on the system message bus Aug 02 11:17:33 raspberrypi udisksd[496]: Error probing device: Error sending ATA command IDENTIFY DEVICE to '/dev/sda': Unexpected sense data returned: 0000: 70 00 01 00 00 00 00 0a 00 00 00 00 00 1d 00 00 p............... 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00...)
  • 18:23, 2 August 2022 176.161.224.230 talk posted a new comment on NASPi (Everything works well if the naspi top cover is open... the moment I close the case with the 4 screws, wifi stops working and the disk start to throw errors. What can I do?)
  • 10:48, 2 August 2022 Lisa talk contribs posted a new comment on PiKVM (1/The X630-A3 has an IS2 Audio In interface, which requires additional wiring to connect. 2/But currently the PIKVM system does not support audio. It depends on the system you are using. 3/The X630-A4 does not support audio.)
  • 14:03, 1 August 2022 108.234.235.47 talk posted a new comment on PiKVM (Can I support audio ?)
  • 10:36, 1 August 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hello， SW is only an external switch interface and cannot realize the auto power on function.)
  • 10:31, 1 August 2022 Lisa talk contribs posted a new comment on X400 V3.0 (Hi， Headphone max output power: 142mW at 16Ω)
  • 10:28, 1 August 2022 Lisa talk contribs deleted comment #2703 on X708-Hardware
  • 10:28, 1 August 2022 Lisa talk contribs posted a new comment on X708-Hardware (Hi， We do not recommend this, please use the same specification of batteries.)
  • 10:24, 1 August 2022 Lisa talk contribs posted a new comment on X708-Hardware (Hi， We do not recommend this, please use the same specification of batteries.)
  • 10:22, 1 August 2022 Lisa talk contribs posted a new comment on X708 (Hi， We do not recommend this. Please use batteries of the same size.)
  • 04:54, 30 July 2022 212.231.185.73 talk posted a new comment on X-C1 Software (Hello. Is it possible to have auto power on in v1.3 using the reserved SW?. Thanks) Tags: Mobile web edit, Mobile edit
  • 22:16, 29 July 2022 77.164.231.31 talk posted a new comment on X400 V3.0 (Raspi 3B+ dac X400 v 3.0: Audio Input RCA L R. What kind of headphone, how many ohm is best to buy. Thank you)
  • 13:18, 29 July 2022 186.84.88.178 talk posted a new comment on X708-Hardware (Can I simultaneously connect a lithium polymer battery in xh2.54 and another lithium polymer battery in ph2.0?)
  • 13:07, 29 July 2022 186.84.88.178 talk posted a new comment on X708 (Can I simultaneously connect a lithium polymer battery in xh2.54 and another lithium polymer battery in ph2.0?)
  • 12:31, 29 July 2022 Lisa talk contribs posted a new comment on NASPi (Hi， Yes，X-C1 can power Pi4 via GPIO cable.)
  • 18:41, 28 July 2022 194.184.204.206 talk posted a new comment on NASPi (Hi, the GPIO cable can power raspberry pi? I mean, if I don't use X823 shield, X-C1 can power raspberry via GPIO cable? Thankyou)
  • 11:48, 26 July 2022 Lisa talk contribs posted a new comment on X735 (Hello， X735 does not affect any USB ports.)
  • 21:09, 25 July 2022 84.220.88.57 talk posted a new comment on X735 (Hi, on a Raspberry Pi 4 only the USB port that receives power is capable of acting as a USB Device. The other USB ports are capable only of acting as USB Hosts. To power the Raspberry and use USB type C at the same time, you have to buy a splitter. Using the x735 module it is possible to be able to use the raspberry type C as a device while the power supply goes into the type C of the x735? Thank you in advance.)
  • 19:12, 25 July 2022 113.88.163.161 talk posted a new comment on X825-C8 (吉安666)
  • 17:03, 25 July 2022 Lisa talk contribs deleted comment #2691 on PiKVM
  • 17:02, 25 July 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， We do not compare with IPMI. In addition, What is the price of IPMI? Most people don't just consider the solution and ignore the price. Of course, if you have enough budget, you can ignore its price.)
  • 16:55, 25 July 2022 Harry talk contribs posted a new comment on PiKVM (Hi, pikvm.org to get more function details. Thanks)
  • 03:29, 24 July 2022 81.221.231.190 talk posted a new comment on X708-Software (unfortunately your node-red flow seem to have a syntax-error... Would you please provide it once more? i am very curious, how you did the node-red implementation. Thanks!)
  • 15:48, 23 July 2022 104.33.135.51 talk posted a new comment on PiKVM (Obviously this is a DIY / opensource version and the latter are enterprise solutions, but how does this compare to IPMI (or for Dell, iDRAC, and HP, ILo or Lights-out)?)
  • 16:30, 21 July 2022 188.235.21.221 talk posted a new comment on X750 Sofrware (You are using python version 3, parentheses should be used for it. Add them to the code or use python version 2)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"