Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 15:23, 6 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1003 (Hi,Sorry, not support turn off LED. you can cover it with black tape.)
• 15:20, 6 January 2025 Lisa talk contribs performed unknown action "comments/add" on EDP to HDMI Adapter (Hi,This is a EDP to HDMI Adapter, NOT support [HDMI to EDP].)
• 15:16, 6 January 2025 Lisa talk contribs performed unknown action "comments/add" on N311 (Hi,The M2.5x4+4mm spacer is used to fix [Bottom Cover + RPi5], M2.5x4 screw is used to fix [Top Cover]. And no need to use M2.5x6+4mm if you don't expand other HAT.)
• 11:51, 3 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1203 (Hello:) Sorry, X1203 does not support changing the charging current via GPIO. we recommend that you replace the battery.)
• 11:42, 3 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1200 (Hi,Once the load is too large, X1200 will turn on overload protection, please confirm the load condition. please check if your power supply is set to 5V 5A (refer to FAQ1)? Please contact us by email support@geekworm.com, and tell us your order number, send the installation diagram.)
• 14:32, 2 January 2025 Lisa talk contribs performed unknown action "comments/add" on NASPi Gemini 2.5 (Hi,Is the noise coming from X882 board? Could you please tell us where the noise is coming from?We recommend that you replace the power supply and test it. If the noise still exists, please email us at support@geekworm.com and tell us your order number and test video.)
• 14:35, 30 December 2024 Lisa talk contribs performed unknown action "comments/add" on Auto Mount an NTFS USB Drive on Raspberry Pi (Sorry I didn't understand your question. Did you buy the Raspberry Pi from our store? If you have questions about your order, please email us and tell us the order number.thank you. support@geekworm.com)
• 14:28, 30 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,It cannot measure current. you can read the battery level through software.)
• 14:20, 30 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1013 (Hi,please refer to Hardware Installation: [https://suptronics.com/Raspberrypi/Interface/x1013-v1.1_hardware.html X1013 Hardware])
• 14:19, 30 December 2024 Lisa talk contribs performed unknown action "comments/delete" on X1013
• 14:19, 30 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1013 (please refer toX1013 Hardware)
• 11:15, 27 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1201 (Sorry, I didn't understand your question. you need to fix the RPi 5 and X1201 UPS with 4 CM2.5*4mm screws.)
• 10:25, 24 December 2024 Lisa talk contribs performed unknown action "comments/add" on X882 (Hello,Dual SATA 2.5" HDD / SSD expansion board for RPi5, Please refer to X1007)
• 10:22, 24 December 2024 Lisa talk contribs performed unknown action "comments/add" on X180 (Hi,X180 has been discontinued.)
• 18:30, 23 December 2024 Lisa talk contribs performed unknown action "comments/add" on GEEKWORM NAS Family (Which product are you using? [4010 3Pin PWM fan] is 5V;)
• 16:03, 23 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1003 (Sorry for the inconvenience, X1003 has been updated to white FFC cable, maybe Amazon warehouse still has some stock with yellow cable, if you need white FFC cable, please email us <support@geekworm.com> （note your order NO. please） ; And thanks for your feedback, glad you share your solution with us here.)
• 15:35, 23 December 2024 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware ([❾ How to programming to get ASD function on V1.2 version] is just an example. You can insert a command to implement ASD function when installing the scriptX708-script.)
• 15:31, 23 December 2024 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware (ASD fundtion is removed on V1.2 version,but you can achieve this function through software programming. please refer to：❾ How to programming to get ASD function on V1.2 version)
• 10:27, 17 December 2024 Lisa talk contribs performed unknown action "comments/delete" on X862 V2.0
• 10:27, 17 December 2024 Lisa talk contribs performed unknown action "comments/add" on X862 V2.0 (Can you please provide the logistics installation diagram and screenshots of the running command errors by the email.support@geekworm.com；pleas tell us your order No. support@geekworm.com)
• 10:26, 17 December 2024 Lisa talk contribs performed unknown action "comments/add" on X862 V2.0 (Can you please provide the logistics installation diagram and screenshots of the running command errors by the email.support@geekworm.com；pleas tell us your order No. support@geekworm.com)
• 10:26, 17 December 2024 Lisa talk contribs performed unknown action "comments/delete" on X862 V2.0
• 10:26, 17 December 2024 Lisa talk contribs performed unknown action "comments/add" on X862 V2.0 (Hi，Can you please provide the logistics installation diagram and screenshots of the running command errors by the email.support@geekworm.com)
• 10:20, 10 December 2024 Lisa talk contribs performed unknown action "comments/add" on X825 V2.0 (It is recommended that you replace a high-quality power supply and test it. a low-quality power supply will damage the expansion board.)
• 10:16, 10 December 2024 Lisa talk contribs performed unknown action "comments/add" on How to read the battery capacity via I2C on X750&725 (please refer to [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1202 Software]----3.0 Reading UPS status)
• 10:14, 10 December 2024 Lisa talk contribs performed unknown action "comments/delete" on How to read the battery capacity via I2C on X750&725
• 10:14, 10 December 2024 Lisa talk contribs performed unknown action "comments/add" on How to read the battery capacity via I2C on X750&725 (please refer to X1202#X1202 Software)
• 18:38, 9 December 2024 Lisa talk contribs performed unknown action "comments/add" on X728-script (Hi，Which version are you using? please check if the script was installed successfully? Software safe shutdown command: x728off DON'T run the 'shutdown' linux command to shut down. You can verify the safety switch through the onboard switch, press and hold the switch for 3 seconds, then the blue LED will flash slowly and the shutdown is going then all LEDs will be off until the device is completely powered off. If the problem still does not appear after checking the above steps, please co...)
• 18:06, 9 December 2024 Lisa talk contribs performed unknown action "comments/add" on How to read the battery capacity via I2C on X750&725 (Hi，The x725 & X750 are no longer in production and we have not tested them with the RPi5. Which UPS HAT are you using?)
• 17:43, 9 December 2024 Lisa talk contribs performed unknown action "comments/add" on X825 V2.0 (Hi,Where is the noise coming from? Can you please send a video by email? and please tell us your order number.<support@geekworm.com>)
• 18:05, 6 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1015 (Hi,Generally speaking, it should not be a power supply problem. You can try another FFC cable to test. and if you use a metal case, it will also have some impact on the WiFi.)
• 10:47, 6 December 2024 Lisa talk contribs performed unknown action "comments/add" on KVM-A3 (Hi，Please send installation pictures or videos via email, and please tell us your order number. support@geekworm.com)
• 09:42, 6 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1001 (It is recommended that you re-flash the OS. Generally speaking, re-flash the OS can solve all problems.)
• 10:31, 5 December 2024 Lisa talk contribs performed unknown action "comments/add" on X862 V2.0 (Remove the screen and just test RPi4 + X862 with SSD， does it work properly? please send the installation picture and your order number by email. support@geekworm.com)
• 16:55, 4 December 2024 Lisa talk contribs created page File:P579-V3-IMG-7181-application.jpg
• 16:55, 4 December 2024 Lisa talk contribs uploaded File:P579-V3-IMG-7181-application.jpg
• 16:54, 4 December 2024 Lisa talk contribs deleted page File:P579-V3-IMG-7181-拓展应用.jpg
• 16:54, 4 December 2024 Lisa talk contribs created page File:P579-V3-IMG-7181-拓展应用.jpg
• 16:54, 4 December 2024 Lisa talk contribs uploaded File:P579-V3-IMG-7181-拓展应用.jpg
• 16:53, 4 December 2024 Lisa talk contribs created page File:P579-V3-IMG-7786.jpg
• 16:53, 4 December 2024 Lisa talk contribs uploaded File:P579-V3-IMG-7786.jpg
• 16:51, 4 December 2024 Lisa talk contribs created page File:Installation Guide-P579+X1001.jpg
• 16:51, 4 December 2024 Lisa talk contribs uploaded File:Installation Guide-P579+X1001.jpg
• 10:57, 4 December 2024 Lisa talk contribs performed unknown action "comments/add" on LVDS2 (Hello，Sorry, we haven't tested it + LVDS2 and can't give any recommendations. Because it is the DIY product, so sometimes there may be the compatibility problem. There are so many different screen models that we can't be compatible with all of them.)
• 10:30, 4 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1001 (Hi,This has nothing to do with x1001, which is just an extension of the RPi5's PCIe.)
• 17:30, 2 December 2024 Lisa talk contribs performed unknown action "comments/add" on X728-script (Hello, X728 does not support that.)
• 16:10, 2 December 2024 Lisa talk contribs performed unknown action "comments/add" on X306 (x306 does not support power failure detection.)
• 15:55, 2 December 2024 Lisa talk contribs performed unknown action "comments/add" on X862 V2.0 (If the X862+Pi4 works normally, it may be due to insufficient power supply.What power supply are you using? It is recommended to use 5V 4A power supply and do not use low-quality power supplies such as those with switches.)
• 15:40, 2 December 2024 Lisa talk contribs performed unknown action "comments/add" on X1013 (It depends on your power supply.)
• 09:59, 29 November 2024 Lisa talk contribs performed unknown action "comments/add" on X1004 (Sorry, we haven't tested it. The height of spacer at the bottom of P580-V2 is M2.5*6mm, and the thickness of SSD + heatsink must be less than 6mm.)