Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 06:27, 20 June 2023 79.214.241.144 talk posted a new comment on X306 (Hi, What about the jumper? I guess if I want to use power switch I have to set it next and in parallel to the USB-Port?) Tags: Mobile web edit, Mobile edit
  • 17:00, 19 June 2023 Walker talk contribs posted a new comment on PiKVM-A3 (Hi, PIKVM-A3 needs to be connected to Raspberry Pi 4)
  • 16:57, 19 June 2023 Walker talk contribs posted a new comment on P165 (Hello, it cannot be powered directly by USB. The interface of the fan is 2pin. It needs to be connected to the GPIO of the Raspberry Pi.)
  • 16:52, 19 June 2023 Walker talk contribs posted a new comment on N300 (the dimensions between holes for pads : 7.7*5cm)
  • 16:47, 19 June 2023 Walker talk contribs posted a new comment on Armor Case B (Hello, the size of this fan is 25*25*7mm, our store currently does not sell fans individually)
  • 16:39, 19 June 2023 Walker talk contribs posted a new comment on X635 (You can refer to this :https://wiki.geekworm.com/PD3005G-3A)
  • 16:38, 19 June 2023 Walker talk contribs deleted comment #3772 on X635
  • 16:38, 19 June 2023 Walker talk contribs posted a new comment on X635 (You can refer to this 【PD3005G-3A】)
  • 16:34, 19 June 2023 Walker talk contribs posted a new comment on Raspberry pi 4 can't find 5ghz wifi (You're welcome)
  • 02:30, 18 June 2023 76.106.40.190 talk posted a new comment on X-C1 Software (Hello, would this fan script work to control the 3-pin version of the Noctua NF-A4x10 5V fan?)
  • 01:08, 17 June 2023 97.126.31.135 talk posted a new comment on X680 (> "four RJ45 ports for ATX power control" This kit does not come with the ATX power control cables... So what is the pinout for the RJ45s if I want to build my own?)
  • 10:03, 16 June 2023 79.184.56.240 talk posted a new comment on P165 (Is it possible to power the fan from the USB port? Could you publish the correct wiring?)
  • 18:41, 15 June 2023 Walker talk contribs posted a new comment on NASPi Gemini 2.5 (Hello, the built-in fan of NASPi Gemini is a PWM 4010 fan. If you find it noisy, you can lower the fan speed. Of course, you can also buy a fan with better quietness. Of course, if you don’t want to install a fan, you can You can use a heat sink with strong heat dissipation, but pay attention to the height between the Raspberry Pi and the shell,)
  • 18:31, 15 June 2023 Walker talk contribs posted a new comment on Raspberry Pi 4 Model B (thanks for your advice)
  • 15:53, 15 June 2023 134.238.128.187 talk posted a new comment on N300 (Hi, can you please provide the dimensions between holes for pads?)
  • 11:39, 14 June 2023 Harry talk contribs posted a new comment on How to enable I2C (This tutorial has been very clear, but raspberry pi OS is constantly updated, so there will be small differences on the latest version. what should we do?)
  • 01:56, 12 June 2023 176.144.226.33 talk posted a new comment on PiKVM-A3 (Is it possible to connect to the kvm from an android smartphone?)
  • 19:18, 11 June 2023 80.224.195.190 talk posted a new comment on Armor Case B (Hi, I'm a owner of this case, and one year later, fans started to do some annoying noise, and I need to replace them. Where I can find others fans with the same specs?)
  • 00:33, 9 June 2023 136.62.160.39 talk posted a new comment on X635 (What PoE module fits this board?)
  • 10:40, 8 June 2023 98.32.5.6 talk posted a new comment on Raspberry pi 4 can't find 5ghz wifi (Thanks, this seemed to stop the wifi dropping for me.)
  • 20:14, 4 June 2023 146.70.202.138 talk posted a new comment on How to enable I2C (Minor suggestion: Even thought the text is clear, the first image appears to suggest that the user follow the menu breadcrumb path of Advanced Options -> I2C Which of course does not exist. I would suggest replacing it with an image that shows the item 3 Interface Options Configure connections to peripherals highlighted rather than what you have now which is 6 Advanced Options Configure advanced settings)
  • 15:49, 4 June 2023 144.2.100.148 talk posted a new comment on NASPi Gemini 2.5 (Is it possible to use the Naspi Gemini without a fan, e.g., with a passive heatsink connected to the casing? My Pi doesn't take big loads and was running fine in a passively cooled enclosure with external HD. If that's not an option, are there any more quiet fans than the included one?)
  • 05:13, 4 June 2023 83.135.166.76 talk posted a new comment on Raspberry Pi 4 Model B (The first hardware revisions of the RPi4 had several issues (ethernet, reboot, usb). For production/critical usage I would only recommend revision 1.4 upwards.)
  • 14:39, 3 June 2023 110.144.66.206 talk posted a new comment on X630 (Thanks for the reply Walker - I'll try those 779 instructions again, but no success in past efforts.)
  • 18:39, 2 June 2023 Walker talk contribs posted a new comment on X728-hardware (Hello, what version of X728 are you using?)
  • 18:21, 2 June 2023 Walker talk contribs posted a new comment on X306 (Hello, the 4 blue LEDs of the X306 UPS Board indicate battery charging and discharging levels of 25%, 50% , 75% and 100%, can only roughly display the percentage of the battery)
  • 18:10, 2 June 2023 Walker talk contribs posted a new comment on X708 (Hello, the fan of X708 is 30x30x10mm, you can replace it with a 30mm silent fan)
  • 18:00, 2 June 2023 Walker talk contribs posted a new comment on X708 (Hello, we have not tested it and cannot give an exact answer)
  • 17:54, 2 June 2023 Walker talk contribs posted a new comment on P252 (Hello, there is an installation guide on the WIKI, which indicates the installation position of each thermal pad, you can take a closer look first)
  • 00:36, 2 June 2023 199.48.201.7 talk posted a new comment on X728-hardware (I have several of these in use and run into the same issue on all of them. They all sit for approx. 3 months powered off without external power. when they are plugged back in the batteries have to be removed and reinstalled before they will function correctly. Is there any way to correct this?)
  • 22:10, 1 June 2023 46.177.208.222 talk posted a new comment on X306 (Can I see the remaining battery percentage?) Tags: Mobile web edit, Mobile edit
  • 13:41, 30 May 2023 70.187.225.182 talk posted a new comment on X708 (Hi, is it possible to change out the fan on this board for another 30mm fan or 40mm with an adapter? I would like to use a full silent fan solution but I want to make sure that replacing the fan is possible. I assume the fan is 5V?)
  • 18:19, 29 May 2023 92.60.179.76 talk posted a new comment on X708 (Hi I tried to connect battery low led to external PH2.0 connector but it seems like it does not light up when battery low blinks on the board and when i run continuity test on that connector (when board is off) there is a short between pins 2 and 3 to ground. I have X708 v2.0, is this my board's fault or schematic has changed for external power switch? It seems like it was reworked to adapt for 4 pin momentary switch with led light (so pins go like this power on/gnd/gnd/power led))
  • 05:14, 29 May 2023 177.23.170.104 talk posted a new comment on X708 (Is there a way to add the x708 sotware to the home assistant, if so, which commands?)
  • 13:34, 26 May 2023 159.196.147.187 talk posted a new comment on Raspberry Pi DIDO Board (If the boards can be addressed, where do you set this address in the software? In the above examples I did not notice the address setting.)
  • 03:39, 24 May 2023 24.56.7.18 talk posted a new comment on P252 (I have a 3B. In the kit I received there are 6 pads that are all 13mm square and one that is 8mm square. The large ones are 2x2mm 2x1.5mm and 2x.5mm. I assume one of the large ones goes in location 3. Should the 2mm pad go on the CPU on top and the 1.5mm go om the bottom, or the other way around?)
  • 15:41, 19 May 2023 Walker talk contribs posted a new comment on X630 (Hello, you can refer to this: https://wiki.geekworm.com/C779-Software There is a guide about audio input on the Raspberry Pi)
  • 15:32, 19 May 2023 Walker talk contribs posted a new comment on X882 (Hello, it can also work if only one driver is installed)
  • 15:29, 19 May 2023 Walker talk contribs posted a new comment on X728 (Hello, in the FAQ on the X728 WIKI page, it is written that we suggest to use the NCR18650B from Panasonic. We have read the battery specifications of 18650 LiFePO4 batteries, and it should be usable. If this LiFePO4 batteries are safer, it is ok It is used, but it needs to be noted that when using batteries and power supply, be careful)
  • 15:10, 19 May 2023 Walker talk contribs posted a new comment on X728-Software (Hello, sorry, we don't have this)
  • 15:08, 19 May 2023 Walker talk contribs posted a new comment on X882 (Hello, I probably understand what you mean, may I ask if it cannot be turned on or the system cannot be started?)
  • 14:48, 19 May 2023 Walker talk contribs posted a new comment on NASPi Gemini 3.5 (Hello, only Pi 4 can be used, Pi 3 can not be used)
  • 14:45, 19 May 2023 Walker talk contribs posted a new comment on X306 (Hi, we are sending you an email, hoping that you can provide some hardware installation pictures. The products are tested before leaving the factory, and there will be basically no quality problems. I hope you can check the test ponits under the Raspberry Pi Zero 2W, are these test ponits clean and the pogo pins align well with each test pins? This may affect the USB ports which make it not work.)
  • 14:36, 19 May 2023 Walker talk contribs posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (You're welcome, thank you for your order)
  • 00:28, 18 May 2023 5.249.127.214 talk posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (Well done,thanks)
  • 07:13, 16 May 2023 96.243.26.200 talk posted a new comment on X306 (None of the USB ports are working. Anything I plug into them does not function and is not listed as connected. What should I do to fix this?) Tags: Mobile web edit, Mobile edit
  • 20:11, 15 May 2023 46.59.194.210 talk posted a new comment on X882 (Somehow my 1.3 seems to not start anymore when I install the script. Anyone experience this as well/has a solution?)
  • 16:29, 14 May 2023 93.38.52.86 talk posted a new comment on X728-Software (Is there a addon for Home assistant?)
  • 07:12, 14 May 2023 184.170.166.131 talk posted a new comment on NASPi Gemini 3.5 (Does this require a RPI 4, or can a RPI 3 be used?)
  • 03:03, 13 May 2023 90.167.51.168 talk posted a new comment on X728 (Hello again, Previous 18650 LiFePO4 comment extended: For X708 model there is the Key Features (wiki-geekworm-com/X708#Features) saying that it "supports 3.7V 18650 lithium battery and 3.7V lithium polymer battery. No capacity limit, only request 3.7V lithium battery". However, on this wiki I couldn't find such information for X728 regarding the kind of batteries supported and the voltage. I just found the recommendation for Panasonic NCR18650B batteries which have 3.6v. I discovered tha...)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"