Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 12:34, 6 October 2022 Lisa talk contribs posted a new comment on X735 Software (Hello， The installation scripts of V3.0 and V2.5 are the same. Refer to the sample script above.Thanks~)
  • 12:29, 6 October 2022 Lisa talk contribs posted a new comment on T208-hardware (Hello， Thanks for your question.please refer topT208#FAQ.)
  • 12:14, 6 October 2022 Lisa talk contribs posted a new comment on X708-Hardware (Hello， 1. The fan of X728-C1 case is only GND 5V ，does not controlled by GPIO. 2. You can unplug it's cable if you want to stop it.)
  • 22:15, 5 October 2022 213.94.32.103 talk posted a new comment on X735 Software (Hi, I installed the fan v3.0 on my raspberry pi4, but the button work only for turning on the pi and for a forced shutdown. How can I enable the reset and safe shutdown? Do you have an installation script for the v3.0?)
  • 04:52, 5 October 2022 86.245.255.107 talk posted a new comment on X708 (Lithium-ion battery are wearing when kept fully charge all the time. To preserve the battery longevity is it possible to limit the maximum capacity/voltage charge ? For Example I would like to limit the charge at 85% maximum. Thanks !)
  • 04:08, 5 October 2022 94.234.116.82 talk posted a new comment on NASPi Gemini (Is the 5v out plug on the board functional?) Tags: Mobile web edit, Mobile edit
  • 23:00, 4 October 2022 2.50.121.7 talk posted a new comment on X708-Hardware (Now that you mentioned it, it makes sense. Since when this happens, it is accompanied by a notable increase in the fan speed. Thank you "Anonymous user #13" whoever you are.)
  • 11:22, 4 October 2022 189.181.238.63 talk posted a new comment on X708-Hardware (HS, is for High Speed. It's used by the fan.py script, when above the threshold it start spinning faster and lowered speed when temp is below threshold. Notice that x708 fan is always running at low speed.)
  • 10:43, 4 October 2022 133.232.65.249 talk posted a new comment on X735 Software (Hello, I bought a cooling fan X735 ver. 3.0 for my raspberry pi 4B and tried to install it. Reading the manual, it seems that X735 has the following GPIOs dedicated. GPIO 5,12,13,16,20 However, my plan is to use the following GPIOs for another purpose. Unfortunately, for various reasons, this cannot be changed. GPIO 16,20,21 Therefore, I would like to change the duplicated GPIOs used for X735 as follows. from 16 to 19 from 20 to 26 How should I rewrite the programs and execute them?...)
  • 22:54, 3 October 2022 46.182.212.220 talk posted a new comment on T208-hardware (Hello, What kind of battery can I use with the T208 ? (Voltage range, max capacity) I'm asking because most 18650 batteries are 3,7V which I'm not sure is up to the specs. If you have any reference to give as an example ; I would be glad.)
  • 21:16, 3 October 2022 102.42.145.124 talk posted a new comment on LHT00SU1 Virtual Oscilloscope SKU:412961 (lht00su1 virtual driver)
  • 20:53, 3 October 2022 2.50.121.7 talk posted a new comment on X708-Hardware (What is the indication of the LED labled (HS) beside the LED labled (FAN) on the x708 v2? It turned red the first time when I connected the ground of the Raspberry Pi with the ground of an external power supply I use to control devices that need more power. Now it is red even when the ground of the Raspberry pi is not connected to anything. The Raspberry pi powers nothing through its 5V)
  • 17:40, 3 October 2022 109.136.113.78 talk posted a new comment on WEMOS ESP32 Board with 18650 Battery Holder (Does someone knows the board I need to select in Arduino IDE to upload my program into this? (from the ESP32 board list))
  • 02:45, 3 October 2022 189.181.238.63 talk posted a new comment on X708-Hardware (Which GPIO pin can be used to control Case Fan x728-C1? Is it possible to stop the x708 board fan? (not LOW but STOP))
  • 10:07, 30 September 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hi， Sorry, it doesn't support Home Assitant yet.)
  • 04:53, 30 September 2022 109.231.0.65 talk posted a new comment on X-C1 Software (Hi, is it possible on Home Assistant?)
  • 02:36, 30 September 2022 176.133.137.224 talk posted a new comment on X-C1 Software (Hello)
  • 12:13, 29 September 2022 Lisa talk contribs posted a new comment on M200 (Hi， 1/Could you please tell us what power supply do you use? If connect external SSD, we suspect maybe the power supply is not enough to power the SSD. 2/Do you mean that you can boot from USB or SSD when use a OTG cable on the NC PORT?)
  • 10:50, 29 September 2022 Lisa talk contribs posted a new comment on NASPi (Hello, You can use GPIO pins other than X-C1 GPIO Use: 4,17,27,18. But we haven't tested if the Naspi case supports the ESP8266.)
  • 02:53, 29 September 2022 69.156.39.124 talk posted a new comment on NASPi (Hi I want to use ESP8266 with this setup but require pins 1,3,5,8 and 10 on the GPIO. Is this possible?)
  • 00:30, 29 September 2022 82.64.55.9 talk posted a new comment on M200 (Why is it not possible to boot on usb port with à bootable usb key or ssd ? Curiously with an otg câble on the n.c. micro usb entry it works...) Tags: Mobile web edit, Mobile edit
  • 19:18, 28 September 2022 207.253.40.113 talk posted a new comment on UPS3 (Hello I have one of your UPS v3 connecter to my Pi. I have activated the Auto UPS feature (on). However, when the Pi is powered off using the poweroff command, the Pi does not restart when power is put back on. What could be the cause?)
  • 10:51, 28 September 2022 Lisa talk contribs posted a new comment on X728-Software (Anonymous user #34 ：Hello， Please use your own username after '/home/pi/'. That is, the username created by the initial user of the Raspberry Pi OS system)
  • 07:44, 28 September 2022 73.240.70.136 talk posted a new comment on X728-Software (I to do not understand how to get the x728 file to work and how to rename to my rpi, Please help The x728v2- say no such file or directory)
  • 09:53, 27 September 2022 Lisa talk contribs posted a new comment on X728-hardware (Hi，You don't have to use the batteries we recommend, but please make sure to use genuine, high-quality batteries. And note the X728's requirements for battery size--[18650 battery dimension] . Thank you.)
  • 12:42, 26 September 2022 186.96.100.60 talk posted a new comment on X728-hardware (Hi, I'm unable to find the recommended battery Panasonic NCR18650B, as a replacement, the seller recommends the Panasonic NCR18650GA, 3450mAh battery. Is it ok to use that model? Thank you very much!)
  • 11:29, 26 September 2022 Lisa talk contribs posted a new comment on NASPi Gemini (Hello， X882 is mainly used for data access, it is recommended that you try to boot from SD card.)
  • 11:26, 26 September 2022 Lisa talk contribs posted a new comment on X876 (Hello， USB +direct 5V power via the pogo pin.)
  • 11:11, 26 September 2022 Lisa talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Please refer to the User Guide above.)
  • 11:11, 26 September 2022 Lisa talk contribs deleted comment #2802 on 2.8 inch Touch Screen for Pi zero
  • 11:10, 26 September 2022 Lisa talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Please refer Use Guide)
  • 00:55, 25 September 2022 70.162.77.57 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (what is the pinout for this?)
  • 02:22, 24 September 2022 66.108.74.250 talk posted a new comment on X735 Software (More legible: testpulse1=$(date +%s%N | cut -b1-13) && echo $testpulse1 testpulse2=$(date +%s%N | cut -b1-13) && echo $testpulse2 pulsegap=$(($testpulse2-$testpulse1)) && echo $pulsegap Warmly yours.)
  • 02:21, 24 September 2022 66.108.74.250 talk posted a new comment on X735 Software (Hmm . . . $ testpulse1=$(date +%s%N | cut -b1-13) && echo $testpulse1 $ testpulse2=$(date +%s%N | cut -b1-13) && echo $testpulse2 $ pulsegap=$(($testpulse2-$testpulse1)) && echo $pulsegap Yields results more like 2000 and 6000, rather than 200 and 600 in the script. Cordially advise changing script to -b1-12 from -b1-13. With kindest regards. Yours sincerely.)
  • 16:38, 23 September 2022 66.108.74.250 talk posted a new comment on X735 (Thank you. With kindest regards. Yours.)
  • 15:53, 23 September 2022 193.253.44.3 talk posted a new comment on NASPi Gemini (Sometime the pi just doesn't boot i'm stuck on a black screen and i have to poweroff/poweron again to be able to start properly. I'm not using RAID (PM mode) and i boot raspbian os lite from one of the two ssd's pluged on the board. I'm also using your official 4a usb-c power adapter. What could it be ?)
  • 14:40, 23 September 2022 Lisa talk contribs posted a new comment on X735 (Hello， After a successful installation of the script, the button switch can perform a safe shutdown.X735 Software Press 1~2seconds -- reboot Press 3~7seconds -- safe shutdown)
  • 19:01, 22 September 2022 31.199.162.190 talk posted a new comment on NASPi (Hi, if I modyfy the file FAN.PY, when it will be reloaded and executed with my updates? Thanks)
  • 16:43, 22 September 2022 Lisa talk contribs posted a new comment on X703 (Hi，There is currently no matching case for x703 + Pi4.)
  • 15:52, 22 September 2022 66.108.74.250 talk posted a new comment on X735 (Good morning. Whereas I purchased X735 V3.0 and a quality 5V power supply; and I have read all documentation and understand set up. May I cordially ask whether pressing the on-board 'blue power button' initiates the shutdown script in the same way as using a momentary switch plugged into JST PH 2.0mm? Many thanks in advance. With kindest regards. Yours sincerely.)
  • 22:18, 21 September 2022 36.73.34.246 talk posted a new comment on X-C1 Software (any fan speed control script for moode audio?)
  • 22:13, 21 September 2022 5.28.97.60 talk posted a new comment on X876 (I am wondering how you power the nvme when the USB3 ports on the 4B only deliver 900mah? how does this solution work? Thank you)
  • 14:06, 21 September 2022 66.108.74.250 talk posted a new comment on X825 V2.0 (Hi, this is Anon 11 again. Thank you for your response. I tried Disk Management. However, my X825 V2.0 (with a 2.5inch SSD inserted) was not detected in Windows. Also not detected in Linux (debian). Not a concern however, as I am content to use my X825 V2 principally in conjunction with rPi4. Whereas for me, attachment standalone to a PC is an edge case. With kindest regards. Yours sincerely.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (Standby current is normally less than 1mA.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (1. Max charging current is 3A 2. We have two DC/DC bosst converters, one is TPS61088RHLR from TI and other one is 2187 from our local.)
  • 10:09, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， The case does not support extended GPIO cables because there is not enough space for the X630-A3 to the top of the case.)
  • 09:35, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi, It is normal, no malfunction, because there are two colors. We will be replacing only one color to solve this problem.)
  • 16:31, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (Can a HAT expander cable be used with this case i.e. is there enough clearance for the connector, and for ribbon cable to get out of lid? It looks as if there is a slot / cut-out but can't be sure about size and position from photos.)
  • 16:13, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (With regards to the yellow apsect of the display, my point was this looks like a fault as part of the bottom of the 'iface: eth0' text is in blue. So the question is - is there a fault with the OLED connectivity?)
  • 07:40, 20 September 2022 78.146.134.222 talk posted a new comment on X708 (What is the total idle/quiescent current draw from the battery to the X708, when the X708 is switched on (not in sleep mode), but there is only a very small current (a few uA) drawn on the output? In other words, what is the X708 battery current just for it to be switched on?)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"