Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 19:09, 5 November 2020 195.35.72.236 talk posted a new comment on X735 (Haben Sie das Skript installiert?)
  • 01:22, 4 November 2020 91.47.17.245 talk posted a new comment on P173 (wow. thats what i call an installation guide.... NOT)
  • 20:54, 2 November 2020 62.141.90.86 talk posted a new comment on LVDS Adapter (Hello I am trying to use converter board v.20 with 1024*768 single mode resolution. And I have no HDMI Output. LCD panel AA104SJ02, connected to the output is working good. I has checked coonection for several times, I can see LVDS input via oscilloscope, power 5v and it is good. I can see 27mzh and 12mzh osillators are working good. S1 jumper is shorted.)
  • 03:55, 2 November 2020 77.99.35.70 talk posted a new comment on X835 (Sorry it is a 3.5" drive, 2.5" below is a typo.)
  • 03:54, 2 November 2020 77.99.35.70 talk posted a new comment on X835 (Hi there, I've got an X835, Raspberry Pi 4B with a WD 2.5" 2TB SATA. Raspberry Pi is up and running with Raspbian (w/ OpenMediaVault running) and fully updated/upgraded. However, my Raspberry Pi is not detecting the SATA drive. It is NTFS formatted but I've confirmed that ntfs-3g (i.e FUSE) is present and up to date. When I disconnect it from my Pi and connect to my Win 10 machine (still inside the X835) it immediately mounts on the Win 10 machine, so I know power and the drive aren't issues....)
  • 02:37, 2 November 2020 5.69.55.218 talk posted a new comment on X835 (got two x835 which work without problems until to day when I was converting them to use USB Boot option on the PI4,Followed the instruction which are on the is wiki. There is a problem when the HDD are 4TB in size the "SD Card copier" fails when it trys to partition 256 and the rest of the drive, the second partion fails to write. (I have the though that there is a 2tb limit) Will try this on the Rasberry Pi org as a problem.)
  • 02:09, 2 November 2020 5.69.55.218 talk posted a new comment on Does the X825/X855 support USB boot (watch out for the minor problem with above link "how to boot ...." this links to tom's hardware but the option for the USB boot if using the latest raspi-config is under option 6 not 3)
  • 04:53, 1 November 2020 178.255.168.219 talk posted a new comment on X835 (Hello! I am using Raspberry Pi 4B (booting from sd card) with a single X835 board and WD blue 3.5" HDD. I have two questions: 1) Is there a way how to configure the system to spin down the HDD (stop its rotation) when inactive for certain time? Currently, the HDD is only used rarely, but it keeps spinning forever. 2) What is the proper way to shut down the system? When I shut down the Pi ($ sudo shutdown -h now), the red PWR LED on the Pi is lit (on) - this is probably normal. The problem...)
  • 18:59, 30 October 2020 Harry talk contribs posted a new comment on X708-Software (Sorry, we updated the script for X708.)
  • 08:07, 29 October 2020 47.17.97.226 talk posted a new comment on UPS3 (The UPS hat stops charging the battery once the main power is reconnected. If I shutdown the raspberry Pi and restart HAT either with push button or with the auto-power switch, only then SOC% start increasing in the log(battery really starts charging). Details below: Steps & Observation: 1. Raspberry Pi powered via HAT and battery is charging, log file shows SOC% going up. 2. Power is disconnected from HAT USB-C 3. Raspberry Pi still remains operational as expected. log file shows SOC% dropp...)
  • 09:21, 28 October 2020 83.26.232.1 talk posted a new comment on Armor Case B (How long can fans (on dual-fan version) run without stopping?)
  • 21:08, 26 October 2020 165.225.207.5 talk posted a new comment on Power Pack Pro (Solution: I will use the transistor to simulate the switch button pressed. I will connect to power the Raspberry pi board and also the UPS board.)
  • 00:05, 26 October 2020 CaptStephan talk contribs posted a new comment on Robot Expansion Board (Can you share how you figured this out in a reply or maybe share a link to a git or something? I am working on this now, trying to add an ultrasonic sensor and wanting to know if I can use these points for that - Thanks, Stephan)
  • 11:33, 25 October 2020 73.77.166.54 talk posted a new comment on X708-Hardware (Directly on the X708 no, the fan is connected directly to power. You could setup a mosfet and use a GPIO pin to toggle if the fan is on or not though.)
  • 11:28, 25 October 2020 73.77.166.54 talk posted a new comment on X708-Hardware (Did some poking around and the pin for the female side PLD was not soldered well. I soldered it using a soldering iron and the problem with the PLD was resolved, so I resoldered every pin on both sides of the board. Looks like along with poor documentation Geekworm also has some quality control problems.)
  • 10:19, 25 October 2020 73.77.166.54 talk posted a new comment on X708-Hardware (I added sudo in front of /etc/x728pwr.sh & in /etc/rc.local and now the momentary switch seems to be working as expected. Also note that the pin descriptions under section 3 above are incorrect. Pin 1 is the NO pin of your momentary switch, Pin 2 is ground or common for the switch, pin 3 is ground for the LED in the switch and pin 4 is +V for the LED in the switch. Pin 1 is the farthest pin from the fan. I found out that the pin to let the Pi know if AC power is good or not was not working...)
  • 07:12, 25 October 2020 174.235.10.190 talk posted a new comment on X708-Hardware (I am having the same problem. The pld python script also does not detect when I unplug AC power. I'm running on a raspberry pi 4 (2018 model) with 4gb of ram. And I used the latest full version of raspberry pi is from today October 24th 2020.) Tags: Mobile web edit, Mobile edit
  • 05:24, 25 October 2020 73.180.6.57 talk posted a new comment on X710 (The software install seems to be trashed. I'm getting something about the website being for sale in the x710.sh file when running the script. I was downloading this to get the momentary switch to work correctly although probably don't need it. Momentary switch with no pins jumpered doesn't reboot or soft shutdown. Only power on and hard power off.)
  • 22:28, 24 October 2020 80.110.98.223 talk posted a new comment on P173 (Where are the instructions?)
  • 12:19, 24 October 2020 99.70.215.164 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Not sure anyone will read this, but how do I disable the touchscreen so that I can utilize i2c for an RTC????)
  • 00:33, 24 October 2020 99.4.122.1 talk posted a new comment on P173 (It would be nice to have the photos illustrating the installation available here - as well as on the Amazon site. All in all, I think that this is a very nice product, and I recommend it, especially for those who don't want to deal with fans.)
  • 21:24, 23 October 2020 84.113.96.128 talk posted a new comment on X730 (Can you please document which of the GPIO pins you use, and which does what?)
  • 16:59, 23 October 2020 Szymon talk contribs posted a new comment on Power Pack Pro (Hi, Could I ask you for advice, which modification will be needed in to the PCB to make this UPS start automatically after back the power after fully discharge the battery. Best Regards Szymon)
  • 14:42, 23 October 2020 203.125.27.78 talk posted a new comment on X728 (Hi, what is the operating temperature and humidity range for this ? Thanks)
  • 17:40, 21 October 2020 37.11.86.124 talk posted a new comment on X835 (hello,i would like to attach 5 hard drive with 8Tb to my raspberry pi 4 using board X835. My question is: 1- can i use just one power supply? 2- if not, how much i need, and how i connect? 3- if yes, is just connect to the first X835 board? (under the raspberry pi) 4- how much TB can support board X835? Thanks)
  • 23:31, 17 October 2020 174.112.226.150 talk posted a new comment on X828 (What is the USB Controller in use, as shown by lsusb? Also, is it using the UAS protocol, as shown in the Driver output of 'lsusb -t'? I just want to be sure before ordering. My plan is to use it for a NAS, and your solution looks excellent, including the two drive case.)
  • 05:39, 16 October 2020 Indigoson talk contribs posted a new comment on X708 (FWIW, I'm using a married set of LG HG2s (married here just means that they've always been used together, never as individual cells; it's likely unimportant here, as the power draw is minimal). These are unprotected, high-capacity, high-drain LiON batteries that can be had at places like IMRbatteries dot com for a few bucks a pop. Highly recommended.)
  • 16:54, 15 October 2020 194.183.173.58 talk posted a new comment on X835 (What is the maximum amount of hdd I can connect to rpi 4 using X835 borads, do I also need to upgrade power supply if use a lot of disks like for example 5+, if yes what is the most convenient way to do so.)
  • 00:39, 9 October 2020 Ok4rm talk contribs posted a new comment on Raspi UPS HAT Board (And one modification. When the USB cable is connecte to a PC, LED1+2 are on and LED3+4 flash, about twice per second.)
  • 00:30, 9 October 2020 Ok4rm talk contribs posted a new comment on Raspi UPS HAT Board (Does not work. Let me describe again. When UPS is stand-alone: 1. after connecting battery, all four LEDs light and never go off 2. after connecting USB cable, LED1+2 flash, after 1 sec all four LED are on, then 1 sec all LEDs go off. 3. battery does not charge When connected to Pi Zero: - everything same as above, but I can read voltage. - it does not charge, anyway)
  • 00:26, 9 October 2020 Hierophant talk contribs posted a new comment on 5 inch HDMI GPIO Touch Screen (Will this work directly to a pi zero w please?)
  • 00:19, 9 October 2020 193.86.27.15 talk posted a new comment on Raspi UPS HAT Board (Does not work. When I connect it to micro USB, LED1+2 switch on, after ~1 sec LED3+4 go on, after yet another ~1 sec all LEDs switch off, and so on... Cannot find any description what this means. When I connect it to RasPi Zero W: I can measure voltage, it works as UPS, but the battery slowly discharges and no charging.)
  • 18:01, 8 October 2020 82.35.153.32 talk posted a new comment on X708 (do we have a step by step guide to do this? what is the enabling step? i would appreciate a noobs guide please thanks!)
  • 17:12, 8 October 2020 82.35.153.32 talk posted a new comment on X708-Hardware (I can't get the x708 to shut down with the momentary switch any ideas how to do this?)
  • 13:46, 8 October 2020 73.109.126.131 talk posted a new comment on UPS3 (This Hat helped with the power problems I had with my Pi setup. I'm very pleased so far. I am unable to get the battery test to work, ill try to figure that out soon. The only thing extra is, that I would have liked to have solder pads for input power along with the current connector. Very Nice... if you could point me to how to fix the batter level indication, I would be appreciated. Also if there is a more detailed user manual than the single sheet. Love the Hat ! I will reccomen...)
  • 13:41, 8 October 2020 79.53.103.11 talk posted a new comment on X750 (The instructions say "Supports safe shutdown and full poweroff through software", but if I shut it down via Logout -> Shutdown the board itself won't turn off, just the Raspberry. Do i have to shut it down using x750off?)
  • 05:15, 8 October 2020 69.130.77.204 talk posted a new comment on X728 (I also had this issue, have you found an answer?)
  • 07:48, 7 October 2020 188.250.16.100 talk posted a new comment on LVDS Adapter (Hi, Interested in "picking up" the signal that normaly goes to a 3.5" TFT. VESA resolution of QVGA. Can it work? Just need to pick my doorbell video signal to inject on my Home Assistant instance)
  • 23:36, 5 October 2020 46.7.249.50 talk posted a new comment on X857 (can't boot Rasp Pi 4 with latest bootloader to boot from M.2 SSD WD green 120gb using X862 shield I am using. Have added power 5v power from X735 V2.1 but still nothing can you help. Pi is booting from SSD but not using X862)
  • 05:07, 3 October 2020 86.165.211.19 talk posted a new comment on X728 (Hello, your x728 board is excellent! I was just wondering though how can I get servos to move position when I shutdown when I press the power switch?) Tags: Mobile web edit, Mobile edit
  • 23:50, 2 October 2020 Heinemann talk contribs posted a new comment on X735 (Benutzername: Heinemann Mein System besteht aus RPi4 8GB, dem Modul X735 V2.1, einem USB3.0 Hub mit separater 5Vdc Einspeisung und einem 5Vdc 5,5A Netzteil. Die 5V Versorgung des Systems erfolgt über den DC5525 Jack des X735 und dieser speist den RPi4 über die GPIO-Pin und den USB3.0 Hub über den 5V Out (XH2.54mm 2pin). An dem USB3.0 Hub sind zwei SSD über USB-Adapter angeschlossen. Die maximale Stromaufname einer SSD beträgt 0,85A. Das System läuft mit den Einstellungen arm_freq=2000 Over_vo...)
  • 21:09, 1 October 2020 AndreK talk contribs posted a new comment on X728 (After charging, the battery capacity measurement is no longer correct and only slowly recovers when the Raspberry Pi has been running for a while? Furthermore, the volt measurement shows 3.6 V but the capacity measurement already shows only 5 percent. What could that be?)
  • 22:21, 30 September 2020 199.91.137.61 talk posted a new comment on X708-Hardware (RPi CPU cooling fan never seems to stop running. Is there something I can do to have it only activate when the Pi needs cooling? Cheers)
  • 22:16, 30 September 2020 199.91.137.61 talk posted a new comment on X708 (It definitely works. I just received mine last couple of days. You must have missed an enabling step, also be sure that you have power connected to x708 and not the PI directly. 1. Enable i2c 2. Reboot 3. clone x728 project from github 4. Open x728.sh and comment out first four lines 5. Install the x728 features/scripts 6. sudo x728softsd.sh #shut it down)
  • 05:37, 30 September 2020 89.247.47.188 talk posted a new comment on X856 (what manufacture and type of usb to sata controller is this device build on?)
  • 05:35, 30 September 2020 89.247.47.188 talk posted a new comment on X857 (what manufacture and type of usb to sata controller is this device build on?)
  • 11:35, 29 September 2020 76.14.247.222 talk posted a new comment on X708-Hardware (Hi, Can we please get some documentation of which GPIO pins do what, and under which conditions? Thanks)
  • 08:40, 27 September 2020 37.201.192.247 talk posted a new comment on X829 (Do I have to run a script in order to see the hard drives or are they are visible after installation?)
  • 02:06, 26 September 2020 92.104.57.117 talk posted a new comment on X825 (Powering the X825 board (without Raspi nor SSD/HDD) with geekworm conform power supply, the red onboard led flashes, so does the power supply's led. It looks like having oscillating shortage on board. Any suggestions to fix that?)
  • 04:11, 25 September 2020 84.112.65.153 talk posted a new comment on X708 (Like the other poster mentioned I do not think 18650 with protection circuit will even fit this board. Can you please confirm/correct the information about the protection circuit?)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"