Open main menu
Geekworm Wiki

KVM-A4

Revision as of 11:49, 27 September 2024 by Abby (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

KVM-A4 V2.0-New Version
KVM-A4-Old Version
X630 HDMI to CSI-2 Module
X630-A5 Packing List
KVM-A4 V2.0 Packing List
KVM-A4 V1.1 Packing List
Difference between X680-A8 cable & X630-A5 cable

Contents

Update History

In August 2023, the X630-A4 has been updated from V1.1 to V2.0 version, the PCB layout and PCB size of X630-A4 has changed a lot.

 

Overview

PiKVM-A4 is one of the members of PiKVM[1] family, it only supports Raspberry Pi Zero 2 W without a matching metal case.

!!! warning "ZeroW reached EOL and is no longer supported, the last image it can be found here"

Or you can refer to here


The PiKVM-A4 is composed of follow parts:

  • X630 HDMI to CSI-2 Board (for video capture)
  • X630-A4 HAT Board (for ethernet, RTC, ATX Control power in etc)
  • X630-A5 Adapter Board (it is installed inside the PC case, and it connect the computer motherboard and IO panel cabe of PC case))
  • 0.96 inch OLED (for display, Resolution: 128×64 pixel)
  • Ethernet Cable (TIA/EIA-568.B connection, and it's ATX control signal cable)

How to Power

  • (For X630-A4 V2.0) Power Input: 5.1Vdc +/-5% , ≥3A (Power Via Micro-USB port of Raspberry Pi Zero 2W)
  • (For X630-A4 V1.1) Power Input: 5.1Vdc +/-5% , ≥3A (Power Via USB Type-C port of X630-A4 V1.1)

How to Cool

  • The new version KVM-A4 V2.0 (X630-A4 V2.0) does not support C296 aluminum heatsink installation, please use the ordinary heatsink for the CPU of Raspberry Pi Zero 2 W.
  • For use with raspberry pi zero 2 w, X630-A4 V1.1 (KVM-A4) allows to use C296 aluminum heatsink with your Raspberry Pi Zero 2 W, but user need to prepare 4pcs M2.5*7mm screws yourself.



Geekworm KVM family products:

Model Compatible With Form Factor Max Input Resolution ATX Control RTC Chipset OLED display PoE RS232 Console Ethernet M.2 NVMe Socket Control of PCs USB HUB I2S audio
KVM-A3 V1.6 Raspberry Pi 4 HAT 1920x1080 @50Hz Yes DS1307 0.96" No No 1GbE No 1 No Yes
In-phase I2S wire
KVM-A8 V1.8 Raspberry Pi 4 PCI 1920x1080 @50Hz Yes PCF8563 0.96"
(Equipped with a 2P
wire to connect the OLED)		 802.3af No 1GbE No 1 No Yes
Inverted-phase I2S wire
KVM-A4 V2.0 Raspberry Pi 2W HAT 1920x1080 @50Hz Yes DS1307 0.96" No No No No 1 No No
X680 V1.5 Raspberry Pi CM4 Box 1920x1080 @60Hz Yes PCF8563 0.96" No No 1GbE 2280 4 Yes No
X680 V1.3
Updated to V1.5 now		 Raspberry Pi CM4 Box 1920x1080 @50Hz Yes DS1307 0.96" No No 1GbE 2280 4 Yes No
X650 V1.3 Raspberry Pi CM4 PCI 1920x1080 @50Hz Yes DS1307 No No No 1GbE No 1 No
X652 V1.0 Raspberry Pi CM4 PCI 1920x1080 @60Hz Yes DS1307 No 802.3af
(POE injector
is required due to
compatibility issues) 		No 1GbE 2280 1 No No


Packing List

  • 1 x 0.96 inch OLED: Resolution: 128×64 pixel, with 2 piece of M2*6 screws
  • 1 x Ethernet Cable (Cable length: 100cm)
  • 1 x X630 HDMI to CSI-2 Module
    • 1 x FPC Cable(8cm length)
  • 1 x X630-A4 V1.1 Expansion Board
    • 1 x USB-A to USB-C OTG Cable (Cable Length: 100cm / 39.37 inch)
    • 8 x M2.5x3mm Screw
    • 3 x M2.5x4+4mm Spacers
    • 1 x M2.5x10+4mm Spacer
    • 1 x M2.5x15+4mm Spacer
    • 2 x M2.5x15mm F/F Spacers
  • 1 x X630-A4 V2.0 Expansion Board
    • 1 x USB-A to Micro USB OTG Cable (Cable Length: 100cm / 39.37 inch)
    • 2 x M2.5x4+4mm Spacers
    • 2 x M2.5x17mm F/F Spacers
    • 1 x M2.5x9mm F/F Spacer
    • 1 x M2.5x15mm F/F Spacer
    • 8 x M2.5x4mm Screws
  • 1 x X630-A5 V1.0 Adapter Board
    • 1 x M3.5x6mm Screw
    • 4 x ATX Control Cable(2pin Female to Female Dupont Cables) (Cable Length: 47cm / 18.50 inch)

  • KVM-A4 V2.0 Packing List

  • KVM-A4 V1.1 Packing List

Installation Guide

Hardware Parameters

KVM-A4 V2.0:

 
 
X630-A4 V1.1 +X630
 
X630-A5 Adapter board

Hardware Installation

For X630-A4 V2.0:

 

For X630-A4 V1.1:

 

For X630-A4 V2.0:

 

For X630-A4 V1.1:

 

Note:

  1. The X630-A5 adapter board will be install into the PC Case.
  2. The wire group ① connect to X630-A5 comes from the PANEL of PC Case.
  3. The black and red wires(wire group ②) come from X630-A5 accessories.

Installation Video

New Version KVM-A4 V2.0: https://youtu.be/RUY6J6LVDhY

Old Version KVM-A4 Kit: https://youtu.be/a2oYTEh7QC0

OS Download & Installation

1. Firstly, need prepair a micro sd card, a minimum 16 Gb class 10 memory card is recommended.

2. Download an appropriate OS image for the PiKVM, the url link is: https://pikvm.org/download/, For Raspberry Pi Zero 2W, please use Raspberry Pi Zero 2 W, V2 platform.

 

!!! warning "ZeroW reached EOL and is no longer supported

3. Flash it to a microSD memory card by following the simple instructions or Official installation tutorial

4. Power the device, then open explore to login the pikvm web ui.

5. Blog sharing for reference: https://www.andysblog.de/kvm-over-ip-pikvm-als-bausatz

Firstly, we recommend carefully reading official documentation from website: https://docs.pikvm.org/faq/.

If you run into any issues you can check the following Q&A. If that still doesn't help you you're welcome to raise an issue ticket at https://geekworm.com/community/forum/topic/78220/pikvm-faq or email to us (support@geekworm.com)

(Please be sure to provide installation pictures or videos to contact us, which can effectively solve the problem.Thanks.)

6. Enable oled on Geekworm PiKVM-A4 Kit

References

  1. ↑ PiKVM © belongs to https://pikvm.org

FAQ

Q: Why KVM-A3/KVM-A4/KVM-A8 does not show the video only display No Signals?

A:

  • Please check the hardware connection. Double-check that the video capture device is connected correctly and tightly.
  • Make sure you use the original HDMI port. If your desktop only has a VGA display port, there may be no video signal when you use VGA to HDMI adapter, and there is no way to solve this; However, you can try to lower the resolution and restart the PC to test, but the probability of success is very low.
  • Change the HDMI cable to test.
  • Test the X630 separately to check if there is HDMI output.(run the ls /dev/video0 command, if you see anything such as /dev/video0 other than file not found, then it’s available )
  • Some laptops do not output any signal until you switch the output (usually via the FN + and an F5 key on the keyboard).
  • Your computer maybe enter sleep mode, please exit sleep mode.
  • Feedback from users: If you're using something like NGINX Proxy Manager, you must have Websockets Support enabled for it to work correctly – screenshots below:
 
  • Feedback from users: Multiple Network IPs. if you'll have similar thing in the future: janus is using stun servers for determining public ip address, if the network has several public IP addresses and route traffic through multiple of those, janus via stun will detect the change of the network and restart the stream each time

Solution: either lock traffic from pikvm through one gateway (one public IP address) or configure some sort of session persistence (sticky connection)

Q: Which pins are available on the KVM-A3?

A: You only can use GPIO16, 26, 11, 17, 25, 9, 10 pins on KVM-A3

Q: I want to control several pc power. Is it possible with one KVM-A3 and several X630-A5?

A. No, one kit can only control one pc, you can refer to X680 to control up to 4 PCs.

Q: How to do if KVM-A8 hangs up or reboot or has to be started manually?

A. The KVM-A8 hardware itself does not cause the system to reboot, and [[KVM-A8 shield is controled by raspberry pi 4;

Please ensure these keys:

1. The PiKVM OS version is correct;

2. Check & use a high-quality power supply;

3. Whether the raspberry pi 4 temperature is too high;

4. Contact us via email to support@geekworm.com

 

If you find that the color wiring is wrong, please contact us at support@geekworm.com

Q. I want to control several pc power. Is it possible with one KVM-A8

A: No, one PiKVM-A8 can only control one pc. Please refer to X680 4-port IP KVM Switch.

Q. How to login pikvm os?

A: Input the XX.XX.XX.XX ip address on the explorer, then input user: admin, the default password is 'admin' also.

Or refer to GETTING TO KNOW THE INTERFACE

Q: How to connect to wifi?

A: Refer to | Optional setting up Wi-Fi

If you want to connect KVM to a Wi-Fi network, you need to tell the device ESSID and password before first boot. To do this, mount the first partition of the memory card (FAT32) and edit or make the pikvm.txt file there. Do not remove line FIRSTBOOT=1 or FIRST_BOOT-1 for first time booting, just add your wifi settings like this: 

FIRSTBOOT=1
WIFI_ESSID='mynet'
WIFI_PASSWD='your password'

There is a possibility that, in countries that support CH13, the device will not connect. You will need to configure your router to disable channels 12-14 or disable Auto scan mode so it will connect.

Save, unmount and follow the next step.

Q. How to switch root user?

A: 

su root
#default password  is root also

Q: Will there will be a case for KVM-A4?

A: No, there is no plan to make a case for KVM-A4, the KVM-A4 kit can only use WiFi NOT ethernet, the match metal case will block the WiFi singal.

Q. Does KVM-A8 support passive heatsink such as (P165-A or P165-B etc) instead of fan?

A: You can use the P165 aluminium heatsink or the H402 pure copper heatsink, but must remove the X630-A8 fan and fan connector.

①If use P165-A(thickness 7mm), you can use M2.5*5mm spacer instead of M2.5*12mm spacer to fix it;

②if use P165-B(thickness 11mm), you can directly use M2.5*6mm screws to fix it;

③if use H402(thickness 4mm), you can use M2.5*8mm spacer instead of M2.5*12mm spacer.

You can also use other suitable spacers + screws to fix the heatsink.

 


Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


<comments />

Retrieved from "https://wiki.geekworm.com/index.php?title=KVM-A4&oldid=21932"