Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 02:53, 29 September 2022 69.156.39.124 talk posted a new comment on NASPi (Hi I want to use ESP8266 with this setup but require pins 1,3,5,8 and 10 on the GPIO. Is this possible?)
  • 00:30, 29 September 2022 82.64.55.9 talk posted a new comment on M200 (Why is it not possible to boot on usb port with à bootable usb key or ssd ? Curiously with an otg câble on the n.c. micro usb entry it works...) Tags: Mobile web edit, Mobile edit
  • 19:18, 28 September 2022 207.253.40.113 talk posted a new comment on UPS3 (Hello I have one of your UPS v3 connecter to my Pi. I have activated the Auto UPS feature (on). However, when the Pi is powered off using the poweroff command, the Pi does not restart when power is put back on. What could be the cause?)
  • 10:51, 28 September 2022 Lisa talk contribs posted a new comment on X728-Software (Anonymous user #34 ：Hello， Please use your own username after '/home/pi/'. That is, the username created by the initial user of the Raspberry Pi OS system)
  • 07:44, 28 September 2022 73.240.70.136 talk posted a new comment on X728-Software (I to do not understand how to get the x728 file to work and how to rename to my rpi, Please help The x728v2- say no such file or directory)
  • 09:53, 27 September 2022 Lisa talk contribs posted a new comment on X728-hardware (Hi，You don't have to use the batteries we recommend, but please make sure to use genuine, high-quality batteries. And note the X728's requirements for battery size--[18650 battery dimension] . Thank you.)
  • 12:42, 26 September 2022 186.96.100.60 talk posted a new comment on X728-hardware (Hi, I'm unable to find the recommended battery Panasonic NCR18650B, as a replacement, the seller recommends the Panasonic NCR18650GA, 3450mAh battery. Is it ok to use that model? Thank you very much!)
  • 11:29, 26 September 2022 Lisa talk contribs posted a new comment on NASPi Gemini (Hello， X882 is mainly used for data access, it is recommended that you try to boot from SD card.)
  • 11:26, 26 September 2022 Lisa talk contribs posted a new comment on X876 (Hello， USB +direct 5V power via the pogo pin.)
  • 11:11, 26 September 2022 Lisa talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Please refer to the User Guide above.)
  • 11:11, 26 September 2022 Lisa talk contribs deleted comment #2802 on 2.8 inch Touch Screen for Pi zero
  • 11:10, 26 September 2022 Lisa talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Please refer Use Guide)
  • 00:55, 25 September 2022 70.162.77.57 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (what is the pinout for this?)
  • 02:22, 24 September 2022 66.108.74.250 talk posted a new comment on X735 Software (More legible: testpulse1=$(date +%s%N | cut -b1-13) && echo $testpulse1 testpulse2=$(date +%s%N | cut -b1-13) && echo $testpulse2 pulsegap=$(($testpulse2-$testpulse1)) && echo $pulsegap Warmly yours.)
  • 02:21, 24 September 2022 66.108.74.250 talk posted a new comment on X735 Software (Hmm . . . $ testpulse1=$(date +%s%N | cut -b1-13) && echo $testpulse1 $ testpulse2=$(date +%s%N | cut -b1-13) && echo $testpulse2 $ pulsegap=$(($testpulse2-$testpulse1)) && echo $pulsegap Yields results more like 2000 and 6000, rather than 200 and 600 in the script. Cordially advise changing script to -b1-12 from -b1-13. With kindest regards. Yours sincerely.)
  • 16:38, 23 September 2022 66.108.74.250 talk posted a new comment on X735 (Thank you. With kindest regards. Yours.)
  • 15:53, 23 September 2022 193.253.44.3 talk posted a new comment on NASPi Gemini (Sometime the pi just doesn't boot i'm stuck on a black screen and i have to poweroff/poweron again to be able to start properly. I'm not using RAID (PM mode) and i boot raspbian os lite from one of the two ssd's pluged on the board. I'm also using your official 4a usb-c power adapter. What could it be ?)
  • 14:40, 23 September 2022 Lisa talk contribs posted a new comment on X735 (Hello， After a successful installation of the script, the button switch can perform a safe shutdown.X735 Software Press 1~2seconds -- reboot Press 3~7seconds -- safe shutdown)
  • 19:01, 22 September 2022 31.199.162.190 talk posted a new comment on NASPi (Hi, if I modyfy the file FAN.PY, when it will be reloaded and executed with my updates? Thanks)
  • 16:43, 22 September 2022 Lisa talk contribs posted a new comment on X703 (Hi，There is currently no matching case for x703 + Pi4.)
  • 15:52, 22 September 2022 66.108.74.250 talk posted a new comment on X735 (Good morning. Whereas I purchased X735 V3.0 and a quality 5V power supply; and I have read all documentation and understand set up. May I cordially ask whether pressing the on-board 'blue power button' initiates the shutdown script in the same way as using a momentary switch plugged into JST PH 2.0mm? Many thanks in advance. With kindest regards. Yours sincerely.)
  • 22:18, 21 September 2022 36.73.34.246 talk posted a new comment on X-C1 Software (any fan speed control script for moode audio?)
  • 22:13, 21 September 2022 5.28.97.60 talk posted a new comment on X876 (I am wondering how you power the nvme when the USB3 ports on the 4B only deliver 900mah? how does this solution work? Thank you)
  • 14:06, 21 September 2022 66.108.74.250 talk posted a new comment on X825 V2.0 (Hi, this is Anon 11 again. Thank you for your response. I tried Disk Management. However, my X825 V2.0 (with a 2.5inch SSD inserted) was not detected in Windows. Also not detected in Linux (debian). Not a concern however, as I am content to use my X825 V2 principally in conjunction with rPi4. Whereas for me, attachment standalone to a PC is an edge case. With kindest regards. Yours sincerely.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (Standby current is normally less than 1mA.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (1. Max charging current is 3A 2. We have two DC/DC bosst converters, one is TPS61088RHLR from TI and other one is 2187 from our local.)
  • 10:09, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， The case does not support extended GPIO cables because there is not enough space for the X630-A3 to the top of the case.)
  • 09:35, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi, It is normal, no malfunction, because there are two colors. We will be replacing only one color to solve this problem.)
  • 16:31, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (Can a HAT expander cable be used with this case i.e. is there enough clearance for the connector, and for ribbon cable to get out of lid? It looks as if there is a slot / cut-out but can't be sure about size and position from photos.)
  • 16:13, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (With regards to the yellow apsect of the display, my point was this looks like a fault as part of the bottom of the 'iface: eth0' text is in blue. So the question is - is there a fault with the OLED connectivity?)
  • 07:40, 20 September 2022 78.146.134.222 talk posted a new comment on X708 (What is the total idle/quiescent current draw from the battery to the X708, when the X708 is switched on (not in sleep mode), but there is only a very small current (a few uA) drawn on the output? In other words, what is the X708 battery current just for it to be switched on?)
  • 07:18, 20 September 2022 78.146.134.222 talk posted a new comment on X708 (I see, so since the IP5310 is used for charging, the maximum charging current of the X708 is 3A? Also, what is the name/part number of the 6A DC/DC boost converter?)
  • 15:54, 19 September 2022 Lisa talk contribs posted a new comment on X708 (Hello， IP5310 is only used for battery charging there is other DC/DC boost converter which can deliver output current upto 6A.)
  • 11:02, 19 September 2022 Lisa talk contribs posted a new comment on X825 V2.0 (Hi， Yes， you can connect X825 V2.0 to PC without Pi4 .please refer here：How to check the X820)
  • 02:35, 19 September 2022 174.204.135.201 talk posted a new comment on X825 V2.0 (Hi this is Anon 11, adding one more detail: Moreover, in the potential 'standalone' configuration, I could provide power to the X825 V2 via its 5.5x2.5 barrel interface for power. With kindest regards. Yours sincerely.) Tags: Mobile web edit, Mobile edit
  • 02:07, 19 September 2022 78.146.134.222 talk posted a new comment on X708 (Your specs say the max output current is 6A, and the max charging current is 4A. But on the datasheet for the IP5310 which is shown on the X708 PCB, the max output current is 3.1A and max charging current is 3A... So, which is the correct specification? 6A out and 4A in, or 3.1A out and 3A in? Also, if 6A and 4A is correct, how did you manage that if it is more than what the IP5310 can provide?)
  • 06:35, 18 September 2022 174.204.132.128 talk posted a new comment on X825 V2.0 (Good morning. Whereas I purchased the X825 V2, a quality 5V power supply, and a quality 2.5 inch SSD; and I have read all documentation and understand set up. Furthermore, I am keen to test whether ---if and when detached from the Raspberry Pi 4--- can X825 V2 be implemented as a standalone SATA-to-USB drive bay-enclosure plugging it via USB to any other PC? May I cordially inquire what I might expect? (I vaguely recall reading in FAQ or commentary of X820 or another expansion board that...) Tags: Mobile web edit, Mobile edit
  • 18:31, 16 September 2022 93.222.150.251 talk posted a new comment on X703 (The X703 requires add. space for the Raspi 4. Is there any recommendation from your side regarding a good fitting case?)
  • 10:33, 16 September 2022 Lisa talk contribs posted a new comment on X301 (Hello， There is no case for the X301 + Pi Zero 2 W / Zero W yet.)
  • 01:08, 16 September 2022 63.84.151.162 talk posted a new comment on X301 (Do you have a case for this?)
  • 16:29, 15 September 2022 Lisa talk contribs posted a new comment on X820 (Thanks for you info. 1）This is related to your SSD timing. 2）Undervoltage---please check your power supply, and you can measure the voltage of PIN2, 4； 3）Only powering the X820 via USB ，It can reboot, and yes, switch does not work 4）If you have an HDD, it is recommended to use the HDD to test it, can reboot normally.)
  • 15:55, 15 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hello， OK,Please email us ：support@geekworm.com ； Thanks！)
  • 23:29, 14 September 2022 84.108.144.120 talk posted a new comment on X820 (Hi, To answer your questions: I usually power the system using MeanWell GST25A05 5V 4A power supply. 1) When I plug the power supply into X820 and RPi is powered from X820 via 2-PIN power cable (and also connected via USB of course) - reboot does not work. 2) When I plug the power supply (the same MeanWell) into RPi and X820 gets the power only from RPi via USB (2-PIN power cable is not used) - reboot works fine. However, there are 2 problems with this configuration i) power butto...)
  • 22:06, 14 September 2022 213.216.218.82 talk posted a new comment on CM4 to CM3 Adapter (Hi,is your adapter RoHS compliant?)
  • 21:13, 14 September 2022 213.144.156.253 talk posted a new comment on PiKVM (Hi, I have a PiKVM-A4 Kit (Pi Zero 2W) and LOVE it Would it be possible to share a 3D model of the assembled boards so I can more easily design a case for it? Or maybe you already have an STL of a case you could share? Thanks!)
  • 17:14, 14 September 2022 84.232.128.171 talk posted a new comment on X820 (Thank you for the info. I can live without the power button on X820 :-))
  • 16:23, 14 September 2022 Lisa talk contribs posted a new comment on X820 (You can power the X820 via Pi3 if using a POE Hat, but the Powers Button Switch on the board will not work.)
  • 14:50, 14 September 2022 84.232.128.171 talk posted a new comment on X820 (How could I power the x820 then from a PoE HAT?)
  • 11:01, 14 September 2022 Lisa talk contribs posted a new comment on X820 (Thanks for your information. How did you power the X820? Could you please try the following tests and tell us the result? 1. Please power via Pi3, not X820.( X820 is not connected to the power supply) 2. Do not use the 2-PIN power cable (RPI and X820 do not need 2-PIN power cable connection))
  • 10:41, 14 September 2022 Lisa talk contribs posted a new comment on X876 (Hello, You can use X735 V3.0, but it's not a power supply. and the metal case not support X735.)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"