Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 17:10, 5 May 2022 Lisa talk contribs posted a new comment on NASPi (Hello， 1.Remove the metal case and test whether it is easy to automatically turn on. 2. Please check if the type c, hdmi port, etc. are aligned? try to adjust the angle slightly. 3. Check if the GPIO cable is firmly inserted)
  • 17:05, 5 May 2022 Lisa talk contribs posted a new comment on X728-Software (sorry，Currently unable to resolve)
  • 07:09, 4 May 2022 174.202.234.136 talk posted a new comment on T208-hardware (I have tested the device with the AON jumper removed, and the t208 behaves as expected when the PLD jumper is in place and the tactile switch is used for power up, however when the AON jumper is installed and power applied to the t208 the blue light comes on and the power on led on the Jetson Nano carrier board lights up but they only stay lit for approx. 4 seconds. After that all LEDs go off and the Jetson Nano can not be powered up using the tactile switch. Can you recommend a way to trou...) Tags: Mobile web edit, Mobile edit
  • 04:26, 3 May 2022 5.57.217.226 talk posted a new comment on LVDS Adapter (Hi. I read all comments and saw these: "Double 8 and singe 8 board are two different boards" "Input LVDS signal must be the standard VESA protocol screen parameters" If it really so what for jumpers VESA/JEIDA and Single8/Double8 on all versions of boards? Is it props or board can really work with different LVDS signals? And main question: which resolution have a HDMI output? Is it depends of input signals? Is this board have a strait conversion or not? It is not described in spec's pdf.)
  • 01:55, 3 May 2022 104.251.66.141 talk posted a new comment on X728-Software (I was able to get the results I wanted by modifying x728bat.py. I changed the 3.00 in the readVoltage line: #Set battery low voltage to shut down, you can modify the 3.00 to other value if readVoltage(bus) < 3.00:)
  • 21:33, 2 May 2022 62.216.207.56 talk posted a new comment on X735 Software (Can you tell me please how to install this script ob my raspiblitz node?)
  • 14:56, 2 May 2022 94.158.53.220 talk posted a new comment on X880 (Is it possible to add additional FAN into X880-C1+X880+X880-A1-A2 on the right side of X880-C1 for HDD? Is there any additional FAN connector for this?)
  • 14:04, 2 May 2022 94.158.53.220 talk posted a new comment on X882 (ETA for case X882-C1?)
  • 13:57, 2 May 2022 94.158.53.220 talk posted a new comment on X882 (X835 compatible?)
  • 06:08, 2 May 2022 104.251.66.141 talk posted a new comment on X728-Software (I have a PI 4B with an x728 V2.1. With my application I really want the x728 to shutdown a short period of time after A/C power loss. I figure I can accomplish this by setting the shutdown voltage higher. When when I run python3 /home/pi/x728/x728v2-asd.py & I only get the battery voltage and percent charge repeating constantly. I see no way to change the shutdown voltage running this command. I edited the shutdown voltage in x728v2-asd.py and run it and the x728 shutdown at my desired v...)
  • 03:13, 2 May 2022 87.159.114.47 talk posted a new comment on X728-Software (is there an addon for this?)
  • 15:37, 1 May 2022 1.177.153.204 talk posted a new comment on NASPi (sometimes when I touch the case, I didnt push power button, naspi turned on. also when I plug in usb memory, naspi turned on. let me know how to insulate it.)
  • 02:48, 1 May 2022 212.51.151.132 talk posted a new comment on X-C1 Software (Hi Lisa Thanks for getting back to me. I try the sleep command but it does not work for me as it only extends the time before the shutdown starts but not the shutdown time itself. I will try to work my way thrue systemd, define the script as a service and find the right order to shutdown. If i will find the right systemd order, i will post it here.)
  • 02:21, 30 April 2022 163.114.132.128 talk posted a new comment on CM4 Stick (How about accessing the console via the USB serial port?)
  • 15:56, 29 April 2022 Lisa talk contribs posted a new comment on T208 (Hi，Please refer T208-hardware; but there is no Auto OFF)
  • 09:29, 29 April 2022 129.126.221.50 talk posted a new comment on T208 (Hi, is there any way to implement both, Auto ON and PLD for Auto OFF within the same operation?)
  • 18:33, 28 April 2022 185.128.194.66 talk posted a new comment on NASPi (I managed to get it working by adding 30 21 * * * sudo /usr/local/bin/x-c1-softsd.sh to the crontab for use pi) Tags: Mobile web edit, Mobile edit
  • 10:51, 27 April 2022 Harry talk contribs posted a new comment on X728 (Hi, check the x728pld.py file, try to comment out the following python code: GPIO.output(BUZZER_PIN, 1) time.sleep(0.1) GPIO.output(BUZZER_PIN, 0) time.sleep(0.1))
  • 04:50, 27 April 2022 189.217.0.185 talk posted a new comment on X728 (by the way, is there a sequence we have to follow to unassmble the hat to avoid damagin itsel or the raspberry?)
  • 04:26, 27 April 2022 189.217.0.185 talk posted a new comment on X728 (Finally got it working, are there any other commands that could be useful? is there a way to disable te buzzer?)
  • 12:24, 26 April 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hi，Andi 5 seconds after the MCU detects the low level, it cuts off the power; this time is sufficient. if you want to change it, you can try this: add ‘/bin/sleep/ 2’ in place of 1 or 2 in the picture File:NASPI-X-C1-shutdown.png . But we haven't tested it this way.)
  • 12:22, 26 April 2022 Lisa talk contribs deleted comment #2507 on X-C1 Software
  • 12:22, 26 April 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hi，Andi 5 seconds after the MCU detects the low level, it cuts off the power; this time is sufficient. if you want to change it, you can try this: add ‘/bin/sleep/ 2’ in place of 1 or 2 in the pictureNASPI-X-C1-shutdown.png. But we haven't tested it this way)
  • 12:15, 26 April 2022 Lisa talk contribs posted a new comment on NASPi (Hi， If you want to perform a timed shutdown, you can add xoff to crontab. But we haven't tested it this way, you can re-debug it. Thanks~)
  • 12:05, 26 April 2022 176.59.202.118 talk posted a new comment on WEMOS ESP8266 Board with OLED & 18650 Battery Holder (Change pins SSD1306Wire display(0x3c, SDA, SCL); to SSD1306Wire display(0x3c, SCL, SDA); That board have some mistakes. For example: if You move joystick Right it will Reset. 8-))
  • 07:31, 26 April 2022 72.215.159.34 talk posted a new comment on X735 (Found the problem and fixed it. The red/black wire was straight through when I received it. I was able to reverse the wire and it turned on. Video gave me the hint. All good.)
  • 06:56, 26 April 2022 72.215.159.34 talk posted a new comment on X735 (Hello, I'm using X735 v3.0 with X832. I followed through with the video and removed the jumper from X832. It will not power on. X832 powers up fine without X735.)
  • 05:02, 26 April 2022 185.128.194.66 talk posted a new comment on NASPi (So if we cant add xoff to crontab how can we perform a timed shutdown ?) Tags: Mobile web edit, Mobile edit
  • 23:06, 25 April 2022 212.51.151.132 talk posted a new comment on X-C1 Software (Hi after run x-c1-softsd.sh my NASPI start to shutdown and powers off after 4 seconds. That seems to be not long enogh for my raspberry os to properly shut down and reach the power off target. My NASPI powers off while systemd is still busy to stop all the processes. Is there a way to extend the time between start the shutdown and power off or even better: check if systemd power off target is reached before power off ? thx best regards Andi)
  • 15:33, 25 April 2022 Lisa talk contribs posted a new comment on X728-Software (Hello， SORRY, libreElec is the readonly image, so don't install our python script.)
  • 15:16, 25 April 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hello，It's a 4010 PWM Fan-3Pin for NASPi. you can buy it from herehttps://geekworm.com/collections/raspberry-pi/products/dc-5v-30mm-40mm-50mm-60mm-cooling-fan?variant=39567352660056)
  • 02:23, 25 April 2022 87.4.53.214 talk posted a new comment on X-C1 Software (after 4 months the fan start to make noise and doesn't have the same performance anymore. Please can someone tell me what model it is, or something compatible? some link where I can buy it, i tried another fan but is working always at max power)
  • 00:11, 25 April 2022 87.159.114.47 talk posted a new comment on X728-Software (Hello, I want to use the X728 v2.1 device with the Libreelec/Kodi distribution. Is there a way or a guide to install the software? The device works flawlessly on Raspian OS. Thanks)
  • 18:11, 24 April 2022 Lisa talk contribs posted a new comment on X728 (Hi，Miguel ①Please do not use USB Type-C and DC Jack power to X728 at the same time. ②When the input voltage is lower than about 4.2~4.5, gradually switch to battery power supply)
  • 17:53, 24 April 2022 46.126.173.109 talk posted a new comment on M200 (Is the aliexpress geekworm official store a good place to buy one?) Tags: Mobile web edit, Mobile edit
  • 17:47, 24 April 2022 46.126.173.109 talk posted a new comment on M200 (Thank you for answer I will buy an M200 board when the raspberry pi zero 2 w is back in stocks) Tags: Mobile web edit, Mobile edit
  • 17:30, 24 April 2022 Lisa talk contribs posted a new comment on M200 (Hi, M200 is JUST a Gigabit Ethernet expansion board,and has nothing to do with the operating system.Whether the operating system is compatible depends on the Raspberry Pi motherboard.)
  • 17:22, 24 April 2022 46.126.173.109 talk posted a new comment on M200 (Is it also compatible with the volumio operating system) Tags: Mobile web edit, Mobile edit
  • 17:22, 24 April 2022 Lisa talk contribs posted a new comment on CM4 to CM3 Adapter (Hi，please refer the picture[Interface definition diagram]; CM4 has gpio0,gpio1; ID_SD of CM4 corresponds to GPIO0, ID_SC is GPIO1)
  • 15:17, 24 April 2022 189.202.90.169 talk posted a new comment on X728 (Good day, Can both input power supplies (USB Type-C and DC Jack) be used at the same time? What would happen if one (or both) of the input's voltage or current drops below the specification? I believe in the event where both the first, and second power supply inputs requirements fail, the AC FAIL LED will light up and the board will now use it's 18650 batteries. Is it safe for the board to receive an input below the requirements? e.g. solar panels outputting 0V at night, or below 5V and be...) Tags: Mobile web edit, Mobile edit
  • 22:35, 23 April 2022 105.247.129.114 talk posted a new comment on CM4 to CM3 Adapter (Hi, trying to connect the official 7-inch LCD. The LCD is set up using I2C on pin3 and pin5 on the CM3, but you have GPIO0 and GPIO1 connected to these pins. According to the CM4 datasheet, there are no GPIO0 nor GPIO1... 2 Questions: 1) Is the I2C connected? If yes, where? 2) To which pins on the CM4 are pin3 and pin5 on the SODIMM connector connected to?)
  • 12:12, 22 April 2022 Lisa talk contribs posted a new comment on X728 (Hi， Short the AON pin； after shutting down, the Raspberry Pi will not restart automatically if the power supply is not replugged in or unplugged. But AON function detection is more sensitive, if it detects a voltage, it will automatically turn on.and we will improve this feature in the future.Thanks~)
  • 10:58, 22 April 2022 Lisa talk contribs posted a new comment on X728 (Hi， The size of the button top batteries may be a bit large. you can use flat top batteries. please refer to：X728-hardware#18650 battery dimension;Please buy the correct size battery.)
  • 16:16, 21 April 2022 189.217.0.185 talk posted a new comment on X728 (Hi, both button top and flat top batteries woudl fit right?)
  • 10:25, 20 April 2022 114.167.187.215 talk posted a new comment on X728 (Is it a specification that the UPS does not power down after the RPI shuts down successfully using the X728? Due to this phenomenon, RPI does not start even if power is supplied to the UPS after shutdown. The AON pin is set to short.)
  • 16:48, 19 April 2022 Lisa talk contribs posted a new comment on CM4 to CM3 Adapter (Hi， Please refer CM4 to CM3 Adapter#FAQQ2)
  • 23:06, 18 April 2022 107.203.254.12 talk posted a new comment on CM4 to CM3 Adapter (It does work with the CM4.)
  • 11:54, 18 April 2022 107.203.254.12 talk posted a new comment on CM4 to CM3 Adapter (Would this work with the CM4 Lite? (No eMMC)) Tags: Mobile web edit, Mobile edit
  • 11:46, 18 April 2022 Lisa talk contribs posted a new comment on M200 (Hi， Yes，because of the size of the M200 board, even if the case retains the SD card slot, it cannot be used. So we didn't design SD card slot. If you have any better suggestion, please let us know. Thanks~)
  • 10:57, 18 April 2022 Lisa talk contribs posted a new comment on X857 (Hi， Could you provide a test video, or some pictures，please？please Email to support@geekworm.com； and let us know your order No，Thanks！)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"