Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 22:13, 21 September 2022 5.28.97.60 talk posted a new comment on X876 (I am wondering how you power the nvme when the USB3 ports on the 4B only deliver 900mah? how does this solution work? Thank you)
  • 14:06, 21 September 2022 66.108.74.250 talk posted a new comment on X825 V2.0 (Hi, this is Anon 11 again. Thank you for your response. I tried Disk Management. However, my X825 V2.0 (with a 2.5inch SSD inserted) was not detected in Windows. Also not detected in Linux (debian). Not a concern however, as I am content to use my X825 V2 principally in conjunction with rPi4. Whereas for me, attachment standalone to a PC is an edge case. With kindest regards. Yours sincerely.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (Standby current is normally less than 1mA.)
  • 12:24, 21 September 2022 Lisa talk contribs posted a new comment on X708 (1. Max charging current is 3A 2. We have two DC/DC bosst converters, one is TPS61088RHLR from TI and other one is 2187 from our local.)
  • 10:09, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， The case does not support extended GPIO cables because there is not enough space for the X630-A3 to the top of the case.)
  • 09:35, 21 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi, It is normal, no malfunction, because there are two colors. We will be replacing only one color to solve this problem.)
  • 16:31, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (Can a HAT expander cable be used with this case i.e. is there enough clearance for the connector, and for ribbon cable to get out of lid? It looks as if there is a slot / cut-out but can't be sure about size and position from photos.)
  • 16:13, 20 September 2022 86.150.112.138 talk posted a new comment on PiKVM (With regards to the yellow apsect of the display, my point was this looks like a fault as part of the bottom of the 'iface: eth0' text is in blue. So the question is - is there a fault with the OLED connectivity?)
  • 07:40, 20 September 2022 78.146.134.222 talk posted a new comment on X708 (What is the total idle/quiescent current draw from the battery to the X708, when the X708 is switched on (not in sleep mode), but there is only a very small current (a few uA) drawn on the output? In other words, what is the X708 battery current just for it to be switched on?)
  • 07:18, 20 September 2022 78.146.134.222 talk posted a new comment on X708 (I see, so since the IP5310 is used for charging, the maximum charging current of the X708 is 3A? Also, what is the name/part number of the 6A DC/DC boost converter?)
  • 15:54, 19 September 2022 Lisa talk contribs posted a new comment on X708 (Hello， IP5310 is only used for battery charging there is other DC/DC boost converter which can deliver output current upto 6A.)
  • 11:02, 19 September 2022 Lisa talk contribs posted a new comment on X825 V2.0 (Hi， Yes， you can connect X825 V2.0 to PC without Pi4 .please refer here：How to check the X820)
  • 02:35, 19 September 2022 174.204.135.201 talk posted a new comment on X825 V2.0 (Hi this is Anon 11, adding one more detail: Moreover, in the potential 'standalone' configuration, I could provide power to the X825 V2 via its 5.5x2.5 barrel interface for power. With kindest regards. Yours sincerely.) Tags: Mobile web edit, Mobile edit
  • 02:07, 19 September 2022 78.146.134.222 talk posted a new comment on X708 (Your specs say the max output current is 6A, and the max charging current is 4A. But on the datasheet for the IP5310 which is shown on the X708 PCB, the max output current is 3.1A and max charging current is 3A... So, which is the correct specification? 6A out and 4A in, or 3.1A out and 3A in? Also, if 6A and 4A is correct, how did you manage that if it is more than what the IP5310 can provide?)
  • 06:35, 18 September 2022 174.204.132.128 talk posted a new comment on X825 V2.0 (Good morning. Whereas I purchased the X825 V2, a quality 5V power supply, and a quality 2.5 inch SSD; and I have read all documentation and understand set up. Furthermore, I am keen to test whether ---if and when detached from the Raspberry Pi 4--- can X825 V2 be implemented as a standalone SATA-to-USB drive bay-enclosure plugging it via USB to any other PC? May I cordially inquire what I might expect? (I vaguely recall reading in FAQ or commentary of X820 or another expansion board that...) Tags: Mobile web edit, Mobile edit
  • 18:31, 16 September 2022 93.222.150.251 talk posted a new comment on X703 (The X703 requires add. space for the Raspi 4. Is there any recommendation from your side regarding a good fitting case?)
  • 10:33, 16 September 2022 Lisa talk contribs posted a new comment on X301 (Hello， There is no case for the X301 + Pi Zero 2 W / Zero W yet.)
  • 01:08, 16 September 2022 63.84.151.162 talk posted a new comment on X301 (Do you have a case for this?)
  • 16:29, 15 September 2022 Lisa talk contribs posted a new comment on X820 (Thanks for you info. 1）This is related to your SSD timing. 2）Undervoltage---please check your power supply, and you can measure the voltage of PIN2, 4； 3）Only powering the X820 via USB ，It can reboot, and yes, switch does not work 4）If you have an HDD, it is recommended to use the HDD to test it, can reboot normally.)
  • 15:55, 15 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hello， OK,Please email us ：support@geekworm.com ； Thanks！)
  • 23:29, 14 September 2022 84.108.144.120 talk posted a new comment on X820 (Hi, To answer your questions: I usually power the system using MeanWell GST25A05 5V 4A power supply. 1) When I plug the power supply into X820 and RPi is powered from X820 via 2-PIN power cable (and also connected via USB of course) - reboot does not work. 2) When I plug the power supply (the same MeanWell) into RPi and X820 gets the power only from RPi via USB (2-PIN power cable is not used) - reboot works fine. However, there are 2 problems with this configuration i) power butto...)
  • 22:06, 14 September 2022 213.216.218.82 talk posted a new comment on CM4 to CM3 Adapter (Hi,is your adapter RoHS compliant?)
  • 21:13, 14 September 2022 213.144.156.253 talk posted a new comment on PiKVM (Hi, I have a PiKVM-A4 Kit (Pi Zero 2W) and LOVE it Would it be possible to share a 3D model of the assembled boards so I can more easily design a case for it? Or maybe you already have an STL of a case you could share? Thanks!)
  • 17:14, 14 September 2022 84.232.128.171 talk posted a new comment on X820 (Thank you for the info. I can live without the power button on X820 :-))
  • 16:23, 14 September 2022 Lisa talk contribs posted a new comment on X820 (You can power the X820 via Pi3 if using a POE Hat, but the Powers Button Switch on the board will not work.)
  • 14:50, 14 September 2022 84.232.128.171 talk posted a new comment on X820 (How could I power the x820 then from a PoE HAT?)
  • 11:01, 14 September 2022 Lisa talk contribs posted a new comment on X820 (Thanks for your information. How did you power the X820? Could you please try the following tests and tell us the result? 1. Please power via Pi3, not X820.( X820 is not connected to the power supply) 2. Do not use the 2-PIN power cable (RPI and X820 do not need 2-PIN power cable connection))
  • 10:41, 14 September 2022 Lisa talk contribs posted a new comment on X876 (Hello, You can use X735 V3.0, but it's not a power supply. and the metal case not support X735.)
  • 20:55, 13 September 2022 92.221.107.65 talk posted a new comment on X876 (Hi Can i use x735 v3 As Power supply via pi for x876)
  • 17:31, 13 September 2022 84.108.144.120 talk posted a new comment on X820 (Here is the additional information you requested: The system is installed on SSD. This SSD with the same SW stack and RPi3b+ but using a different Sata to USB adaptor (instead of X820) works fine and supports reboot. As you requested, I also tried a setup with just OS without Supervised HA - same problem on X820, reboot does not work. Please note that I am using the latest version of 64-bit raspbian OS. I tried both full version and the lite version (without desktop) - the same problem ex...)
  • 14:52, 13 September 2022 Lisa talk contribs posted a new comment on X820 (Hi，Is the system installed on the HDD?)
  • 14:43, 13 September 2022 Lisa talk contribs posted a new comment on X820 (Hi， Please do not install Supervised HA and test whether the Auto On function can be used.Thanks~)
  • 11:23, 13 September 2022 Lisa talk contribs posted a new comment on X703 (Hi， Please use high quality 18650 battery such as Panasonic. And note the battery size（Please choose a flat-top battery, and the battery with a raised positive electrode is larger in size.）)
  • 11:21, 13 September 2022 47.35.238.71 talk posted a new comment on X862 V2.0 (I have a V2 product, and neither the 2.4GHZ or the 5GHZ network can connect. The 'solution' about moving or not using a wireless keyboard is not a solution for most RPI4 installations.)
  • 17:48, 12 September 2022 62.214.252.196 talk posted a new comment on X703 (Do you have any recommendations for a good battery that I can use with X703?)
  • 23:40, 10 September 2022 84.108.144.120 talk posted a new comment on X820 (I am using X820 (v3.0) with RPi 3b+ running Raspbian + Supervised HA installation (fresh installation, all SW latest versions). Unfortunately the system gets stuck when I reboot it (sudo reboot) - it goes down but it does not come up automatically. I have to manually power it off and on using the button. X820 is jumpered to Auto ON position. Are any additional settings required for reboot to work? Any other insights you can offer?)
  • 10:05, 7 September 2022 Lisa talk contribs posted a new comment on X820 (Hi， It is not recommended to power X820 board via Raspberry Pi3.)
  • 05:03, 7 September 2022 84.232.128.171 talk posted a new comment on X820 (Can I power the X820 (v3.0) through the barrel plug from the Pi GPIO 5v pins?)
  • 15:02, 5 September 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， Yellow part： iface eth0 The display can show the temperature, IP address and other information of the Raspberry Pi)
  • 12:59, 5 September 2022 109.155.157.24 talk posted a new comment on PiKVM (What gives with the Yellow part of the OLED display? Thought it was just the demo picture, but also shows up on video and was commented on by purchaser on Aliexpress.)
  • 11:44, 5 September 2022 Lisa talk contribs posted a new comment on X735 (Hi，Please refer to X735 Software NOTE: The install.sh script will make sure this command line is put into the rc.local file, you don't need to do anything. Please change 'python' to 'python3' if you are using python3. Please make sure the file path of pwm_fan_control.py is correct.)
  • 11:39, 4 September 2022 172.58.179.54 talk posted a new comment on X735 (It was a python 3 issue. I changed python to python3 in the pwm_fan_control.py) Tags: Mobile web edit, Mobile edit
  • 03:59, 4 September 2022 24.206.153.129 talk posted a new comment on X735 (Hi, After installing the script, the pwm_fan_control.py file does not run. I get the following message: Can't connect to pigpio at soft(8888) Did you start the pigpio daemon? E.g. sudo pigpiod Did you specify the correct Pi host/port in the environment variables PIGPIO_ADDR/PIGPIO_PORT? E.g. export PIGPIO_ADDR=soft, export PIGPIO_PORT=8888 Did you specify the correct Pi host/port in the pigpio.pi() function? E.g. pigpio.pi('soft', 8888) I ran the killall pigpiod command before trying the...)
  • 18:14, 2 September 2022 Lisa talk contribs posted a new comment on X832 (Hi，Please email us [support@geekworm.com] and tell us your order number, and send your test results, such as video or pictures. We will provide you with after-sales support.Thanks~)
  • 15:43, 2 September 2022 217.116.219.195 talk posted a new comment on X832 (Lisa, hi My previous comment is named user 3# I have followed both your instruktions linked in your answer and I find no difference. My Raspberry, can't show any HDD through the X832. If I connect the same HDD through any HDD enclosure and plug it into the Raspberry , the HDD is recognized. I am pretty convinced that the X832 Is broken. Regards Peter BTW I can't login or create an account here, I have one at the Geekworm main site, but can't use it here. That why this comment is anonymous)
  • 16:57, 31 August 2022 Lisa talk contribs posted a new comment on X728 (If the voltage there still present, then the X728 cannot implement auto-on. we can change the script or a resistor to match your applicaiton but will need to know the timing from 5V to 0V after key off. for this new verison, we changed the MCU and auto-on shoud be more reliable as long as the timing is confirmed. <gallery>X728-out on.png|for X728 V2.2 auto-on</gallery>)
  • 16:57, 31 August 2022 Lisa talk contribs deleted comment #2745 on X728
  • 16:54, 31 August 2022 Lisa talk contribs posted a new comment on X728 (If the voltage there still present, then the X728 cannot implement auto-on. we can change the script or a resistor to match your applicaiton but will need to know the timing from 5V to 0V after key off. for this new verison, we changed the MCU and auto-on shoud be more reliable as long as the timing is confirmed. <gallery>X728-out on.png|for X728 V2.2 out on</gallery>)
  • 16:50, 31 August 2022 Lisa talk contribs deleted comment #2744 on X728
  • 16:50, 31 August 2022 Lisa talk contribs posted a new comment on X728 (If the voltage there still present, then the X728 cannot implement auto-on. we can change the script or a resistor to match your applicaiton but will need to know the timing from 5V to 0V after key off. for this new verison, we changed the MCU and auto-on shoud be more reliable as long as the timing is confirmed. X728-out on.png)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"