Open main menu
Geekworm Wiki

Comments log

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 04:43, 22 May 2019 74.134.210.171 talk posted a new comment on Raspi UPS HAT Board (Use the micro switch on the HAT to turn power to the Pi on and off. After your "shutdown -h now" command on the Pi, press and hold the micro switch on the HAT and the green LED will go out. The 4 white LED's are just showing the state of the 3.7v 2500...)
  • 10:41, 20 May 2019 112.207.101.134 talk posted a new comment on RPI Lithium Battery Expansion Board SKU:435230 (What are the dimensions (length & wifth)?)
  • 09:31, 20 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, 1. Please send us your order number and item link to support@geekworm.com. 2.Please also attach some photos or a video to show the details, thank you. 3.Please try to not used the momentary switch but use the on board power button to have a...)
  • 20:56, 19 May 2019 174.231.135.46 talk posted a new comment on X735 (I am using momentary switch and after 1-2 seconds of holding the power button it is supposed to reboot but instead it instantly shuts off. 1. not rebooting 2. because it is not rebooting and instantly turning off I suspect its a forceful shutdown.)
  • 15:16, 17 May 2019 Admin talk contribs posted a new comment on X735 (Hello, Could you please what project do you need to use? Maybe you can contact us with support@geekworm,com for more destails. Best regards, Cindy)
  • 14:25, 17 May 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hello, This board is limited to LVDS output, the resolution must be the VESA standard, and the driver board should be at least V59 grade. Best regards, Cindy)
  • 12:15, 17 May 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, Yes, The IR-CUT Camera is compatible with all generations of Raspberry Pi(Pi 3 Model B/ Pi 2B/ B+/ A+/ Zero).)
  • 12:14, 17 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello sir, It is a little hard to figure out the problem here. Could you please send us a detail video about the process? Please send to email support@geekworm.com . Please attach an order number and item link thanks! Best regards, Cindy)
  • 19:20, 15 May 2019 86.134.26.26 talk posted a new comment on X735 (We need function in software to power off then power on after maybe 10 seconds. Reboot not sufficient to reset some USB devices. Power off/on cycle triggered by software and HW watchdog. Must be remote, not manual press switch. Do you have product to d...)
  • 02:40, 15 May 2019 49.32.211.160 talk posted a new comment on LVDS To HDMI Adapter Board (Will this work for 800*480 output from LCDs?)
  • 04:09, 14 May 2019 193.114.98.214 talk posted a new comment on RPi IR-CUT Camera (does this camera connect to the raspberry Pi zero ?)
  • 13:10, 11 May 2019 200.105.254.229 talk posted a new comment on Raspi UPS HAT Board (By the way. I have not yet installed any drivers.)
  • 13:09, 11 May 2019 200.105.254.229 talk posted a new comment on Raspi UPS HAT Board (Hi! Could you please explain the correct procedure to have the UPS turn off? This is what I am doing: 1. I first shutdown the Raspberry. `shutdown -h now` 2. Then I press the power pushbutton. The energy is gone on the Raspberry. 3. The UPS LEDs stay...)
  • 04:35, 11 May 2019 181.198.15.236 talk posted a new comment on Raspi UPS HAT Board (Hi! I had the same issue once I left the Raspi running for a couple of hours. I think the SD got corrupted for some undervoltage. The undervoltage symbol used to appear on the right whether connected or not. Nonetheless, I left the UPS disconnected for...)
  • 04:32, 11 May 2019 181.198.15.236 talk posted a new comment on Raspi UPS HAT Board (Nice!)
  • 11:17, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello, your method is not suggest because power supply for X820 cannot be controlled by X735 and safe shutdown won't be implemented as well. Best regards, Cindy)
  • 11:16, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, The GPIO4, GPIO17 and GPIO18 is used for power management.The rest is available for use. Best regards, Cindy)
  • 09:13, 10 May 2019 Admin talk contribs posted a new comment on X735 (Hello, When istall the X735, you can power from the X735 board DC port by the power supply to X820 board by connect the 2pin cable as in the right photo of X735+X820 board.This is rigt way to power the kit. Thanks very much for your understanding! Best...)
  • 09:10, 10 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Would you mind tell us what problem have you met? Please send us your order number and item link and with photos and problem details to email ： support@geekworm.com . Then we can help you with it, thanks very much! Best regards, Cindy)
  • 09:05, 10 May 2019 Admin talk contribs posted a new comment on Armor Case (Hi, For 3B+, you need to use 3 pcs of the thermal pads. Please refer to the wiki page above photos!)
  • 08:42, 10 May 2019 Admin talk contribs posted a new comment on X830 V2.0 (Hello friend, We do not test it on an Asus Tinkerboard S, and the safeshutdown function will not work with an Asus Tinkerboard S. Best regards, Cindy)
  • 08:37, 10 May 2019 Admin talk contribs posted a new comment on X850 (Hi, Sorry, maybe no, if you need one, please contact us by sp@geekworm.com.)
  • 00:26, 10 May 2019 84.84.53.102 talk posted a new comment on X850 (Hi Cindy, When will the USB 3.0 bridge be available as a separate item?)
  • 23:15, 9 May 2019 94.138.44.146 talk posted a new comment on X830 V2.0 (Hello is it compatible with an Asus Tinkerboard S?)
  • 00:09, 8 May 2019 189.51.183.52 talk posted a new comment on X735 (what are the GPIOs used in the script? Because I have some being used in other scripts and I didn't want them to conflict)
  • 16:22, 6 May 2019 62.157.37.152 talk posted a new comment on Raspi UPS HAT Board (Continuing from the last question: In the video above the Dual Micro USB cable is used to power the system. Now at one point the cable is pulled from the wall plug. Now the system is in battery mode with the USB connector of the RPi and the UPS hat be...)
  • 16:11, 6 May 2019 189.40.73.146 talk posted a new comment on X735 (What if I connect the x820 XH2.54 5v to the IN of the X735, and then connect the power supply to the x820. Will the safe sh work?)
  • 15:35, 6 May 2019 89.97.236.20 talk posted a new comment on Armor Case (Thank you Cindy! In this thread someone is reporting different thickness, but I think mine are like the one you cited. Just to clarify more: which pads are needed on Pi3B+?)
  • 14:58, 6 May 2019 Admin talk contribs posted a new comment on X822 (Hello sir, There is a USB HUB chip on the X822 board, so it is only need to connect one usb bridge or USB cable to provide the data of both hdd. Hope to get your understanding!)
  • 14:56, 6 May 2019 Admin talk contribs posted a new comment on X822 (Hello, The X822 support 2 pcs 2.5 inch SATA hard drives, and the RAID 1 drives depends on the software not on hardware, hope to get your understanding!)
  • 14:47, 6 May 2019 Admin talk contribs posted a new comment on 3.5 inch TFT 800x480@60fps (Thanks very much for your feeback!)
  • 14:44, 6 May 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, sorry no, could you please tell us why you need the dimensions?)
  • 14:41, 6 May 2019 Admin talk contribs posted a new comment on X350 (Hi, sorry, no.We dot not suggest to replace it.)
  • 14:39, 6 May 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, We are so sorry, we can not confirm the compatibility.)
  • 14:38, 6 May 2019 Admin talk contribs posted a new comment on X720 (Hi, It is said that it can be releazied by WOL client software.But we do not test this,hope to get your understanding!)
  • 14:13, 6 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, If there is no external power , there is no need to connect the USB to Dual Micro USB Charging Cable.)
  • 14:07, 6 May 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Sorry, it is not available now.)
  • 19:20, 5 May 2019 Admin talk contribs posted a new comment on X735 (Hello sir, Yes, you are right, we will attched the photos of raspberry pi and X820 and X735 board later.)
  • 14:35, 5 May 2019 62.157.37.152 talk posted a new comment on Raspi UPS HAT Board (Hi, Connecting two USB-cables to RPi and UPS means that the 5V input on the UPS is directly connected to the 5V-pins of the RPi (Pin 2 and 4, see schematic of RPi). What happens when no external power is available and the system switches to battery po...)
  • 09:20, 4 May 2019 174.103.75.225 talk posted a new comment on X822 (Could this board support using two 2.5 SATA Hard drives as RAID 1 drives allowing the Raspberry Pi to function as a server?)
  • 03:29, 4 May 2019 178.189.12.122 talk posted a new comment on X720 (Is it possible to power on the rpi on a predefined time?)
  • 20:07, 1 May 2019 83.26.254.131 talk posted a new comment on EXP GDC (Is my laptop compatible (SAMSUNG NP350V5C-S0FPL) ?)
  • 17:49, 1 May 2019 176.130.174.168 talk posted a new comment on RPi IR-CUT Camera (Hello, anyone knows the exact dimentions (or drawing) for the mechanical interface of the camera P/N 497358 ? Help will be apreciate)
  • 11:10, 1 May 2019 222.110.24.108 talk posted a new comment on X350 (is that Omnidirectional microphone onboard ? could i replace onboard microphone better than now)
  • 06:33, 1 May 2019 179.209.194.139 talk posted a new comment on X735 (to make the safe shutdown work. do I have to connect the x820 by the XH2.54 2Pin Cable to the x735 and connect the power supply to the x735?)
  • 06:28, 1 May 2019 179.209.194.139 talk posted a new comment on X822 (do one usb provide the data of both hdd or us1 is for hdd1 and usb2 is for usb2?)
  • 03:44, 1 May 2019 181.160.243.7 talk posted a new comment on Raspi UPS HAT Board (How can I control the switch from gpio?)
  • 22:25, 30 April 2019 80.88.23.208 talk posted a new comment on 3.5 inch TFT 800x480@60fps (Dimming the backlight via I2C is possible. It is also possible to switch the display off and on again. But there seems to be a problem with the standby mode: After waking from standby the display is extremely sensitive on touching the boarder. It flick...)
  • 04:33, 30 April 2019 66.219.150.142 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Can you dim the backlight on the original version?)
  • 09:13, 29 April 2019 Admin talk contribs posted a new comment on USB 16x2 RGB LCD (Hello, What problem have you met? which step is not working?)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"