X1207

From Geekworm Wiki
Revision as of 11:49, 22 December 2025 by Harry (talk | contribs) (→‎Safety Instructions & Warnings)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

X1207 V1.2 Interface Schematic
X1207 V1.2
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5

Safety Instructions & Warnings

  • It is essential to read and understand these safety instructions and warnings before charging your batteries.
  • Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.
  • Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
  • Do not mix and use old batteries with new batteries, or batteries with different brand names.
  • Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.
  • When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.
  • Keep the UPS shield away from children to ensure their safety.
  • Ensure your fingers do not touch the solder pads when inserting the battery into the battery holder, as this could cause a short circuit. This is extremely important!!!
  • Make sure to insert the battery before turning on the UPS.
  • Make sure to insert the battery before connecting the external charger to charge it.
  • Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/
  • Battery Recommend for Geekworm UPS board, please refer to: File:NCR18650B.pdf

Overview

The X1207 is a PoE-powered UPS HAT designed for Raspberry Pi 5, delivering reliable 5.1V/5A backup power to maintain uninterrupted operation. It supports high-demand setups and complies with IEEE 802.3af/at PoE standards, drawing up to 25W from a compatible POE switch while providing both power and network connectivity over a single cable.

With intelligent power management, it monitors Pi status, cuts power after shutdown to conserve battery, and features ultra-low standby consumption. The board ensures seamless power switching during outages and supports auto power-on and AC loss detection.

Model Compatible with Position Lithium battery type Battery Holders Power Input Connector Power Output Connector Note Matching Case
X1200 Raspberry Pi 5 Bottom 3.7V 18650 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1200
 5Vdc Power Output XH2.54-2P x2 - X1200-C1
X1201 Raspberry Pi 5 Bottom 3.7V 18650 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1201
  • 5Vdc ≥3A via XH2.54-2P connector of X1201
 5Vdc Power Output XH2.54-2P x3 Ultra-thin X1201-C1
X1202 Raspberry Pi 5 Bottom 3.7V 18650 Battery 4-Cell
  • 5Vdc 5A via USB Type-C of X1202
  • 6-18Vdc ≥3A via DC 5521 power jack of X1202
  • 6-18Vdc ≥3A via XH2.54-2P connector of X1202
 5Vdc Power Output XH2.54-2P x2 - X1202-C1
X1203 Raspberry Pi 5 Bottom 3.7V Lithium Battery No battery holder
  • 5Vdc 5A via USB Type-C of X1203
  • 6-18Vdc ≥3A via DC 5521 power jack of X1203
  • 5Vdc ≥3A via XH2.54-2P connector of X1203
 5Vdc Power Output XH2.54-2P x2 - -
*X1205 Raspberry Pi 5 Bottom 3.7V 21700 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1205
  • 9-18Vdc ≥3A via DC 5521 power jack of X1205
  • 9-18Vdc ≥3A via XH2.54-2P connector of X1205
 5Vdc Power Output XH2.54-2P x2 - X1205-C1
*X1206 Raspberry Pi 5 Bottom 3.7V 21700 Battery 4-Cell
  • 5Vdc 5A via USB Type-C of X1206
  • 5-6Vdc ≥3A via DC 5521 power jack of X1206
  • 5-6Vdc ≥3A via XH2.54-2P connector of X1206
 5Vdc Power Output XH2.54-2P x2 - X1206-C1
*X1207 Raspberry Pi 5 Top 3.7V 21700 Battery 1-Cell
  • 5Vdc 5A via USB Type-C of X1207
  • 35-57VDC powering over Ethernet
 - Support PoE-Powered

X1207-C1

*X1208 Raspberry Pi 5 Top 3.7V 21700 Battery 1-Cell
  • 5Vdc 5A via USB Type-C of X1208
 - Support M.2 NVMe SSD 2230/2242/2280

X1207-C1

*X1209 RPi 5B/4B/3B/3B+ Top 3.7V Lithium Battery No battery holder
  • 5Vdc 5A via USB Type-C of X1209
  • 6-18Vdc ≥3A via DC 5521 power jack of X1209
 5Vdc Power Output XH2.54-2P x2 - --

Features

For use with Raspberry Pi 5 Model B
UPS Output
  • Built for continuous, long-lasting operation -providing unwavering power for always-on Raspberry Pi systems
  • Supports a maximum current output of 5.1V 5000mA, suitable for most Raspberry Pi applications
  • Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss
  • Power the Pi directly through the 40-pin header, eliminating the need for cables and soldering
Battery Charging
  • Supports battery charging with a capacity of 1500mA
  • Battery charging control can be managed via GPIO
  • Provides protection against battery overcurrent and overvoltage
  • Built-in protection against reverse connection of battery cells
  • Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over i2c
  • On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
  • Features a single 21700 battery holder, supporting battery of up to 5000mAh
Power Input
  • Supports Power over Ethernet (PoE) input capability
  • Provides up to 5A output current, enabling 1.5A charging while powering the system
  • Standard Compliance: IEEE 802.3af & 802.3at (PoE+)
  • Fully isolated switched-mode power supply (SMPS) topology
  • Simplified single-cable installation and robust power delivery for Raspberry Pi
  • Compatible with Raspberry Pi USB-C Power Supply
Enhanced Power Management
  • Seamless power switching between backup power and power adapter
  • On-board push button performs the same actions as the Pi's power button
  • Automatically cuts off power when the Pi is shut down
  • On-board LED indicates power status and Pi detection
  • AC power loss and power adapter failure detection via GPIO
  • Auto power-on when power is applied or restored
  • Automatic safe shutdown when battery voltage is low (programmable)
  • Ultra-low standby power consumption to maximize battery life
  • Advanced system power-path management to minimize frequent charging and discharging of batteries
Compatible Accessories
  • X1002 single NVMe shield for Pi5
  • X1005 dual NVMe shield for Pi5
Notes
  • DON'T apply power to your Raspberry Pi 5 via the Type-C USB socket.
  • Compatible with unprotected 21700 battery only (Max. length: 70.3 mm).

Technical specification

Power input
  • 35-57VDC powering over Ethernet
  • 5Vdc 5A via USB-C
UPS output
  • 5.1V ±5% Max 5A
Battery charging current
  • 1.5A
Terminal Battery Voltage
  • 4.23V
Battery Recharge Threshold
  • 4.1V
Ports & Connectors
  • 4-pin POE female header x1
  • USB-C power in connector x1
  • 1-cell 21700 battery connector x1
  • 40-pin extended GPIO header x1
PCB Size
  • 86.5mm x 84.5mm

User Manual

Packing List

  • X1207 V1.2 UPS board x 1
  • Spacer M2.5 F/F 13.5mm x 4
  • Screw M2.5x5mm x 8
  • Pogo pin x 1 (For connecting to the Pi 5 PSW through hole)

X1207-IMG-0015-Packing-List.jpg

Matching Case

The X1207-C1 is a premium metal case specially designed for the Raspberry Pi 5 X1207/X1208 UPS Shield, offering robust protection in a sleek, black aesthetic.

  • Case dimension: 92.8 x 90.8 x 42.8 mm

  • X1207-C1 Accessories

  • X1207-C1

  • X1207-C1

  • X1207-C1

FAQ

Q1: Question 1

A: Place the answer here.

Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Retrieved from "https://wiki.geekworm.com/index.php?title=X1207&oldid=24282"