X1209: Difference between revisions
Created page with "{{GD Template Impl}} ==Overview== The '''X1209''' is a dedicated UPS expansion board for the Raspberry Pi, delivering reliable '''5.1V/6000mA backup''' power to ensure uninte..." |
|||
| (34 intermediate revisions by 6 users not shown) | |||
| Line 1: | Line 1: | ||
{{GD Template Impl}} | {{GD Template Impl}} | ||
[[File:X1209-IMG-9926-Interface.jpg|thumb|right|X1209 V1.0 Interface]] | |||
[[File:X1209-IMG-0078.jpg|thumb|right|X1209 V1.0 Display_01]] | |||
[[File:X1209-IMG-0081.jpg|thumb|right|X1209 V1.0 Display_02]] | |||
[[File:X1209-IMG-0111.jpg|thumb|right|X1209]] | |||
[[File:X1209-IMG-0112-pogo-pin-connection.jpg|thumb|right|How to Use the Pogo Pin]] | |||
[[File:X1209-IMG-0125.jpg|thumb|right|Battery Installation Instructions]] | |||
[[File:X1209-IMG-0105-How-to-Power.jpg|thumb|right|How to Power]] | |||
[[File:X1209-IMG-0118.jpg|thumb|right|X1209 V1.0 Final Showcase with Battery Holder]] | |||
==Safety Instructions & warnings== | |||
* {{Red|The default charging current is set to 2.1A and charge cut-off voltage is 4.23V. Before connecting your battery to the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.}} | |||
* {{Red|It is essential to read and understand these safety instructions and warnings before charging your batteries.}} | |||
* {{Red|Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.}} | |||
* {{Red|Never make a wrong polarity connection when charging or discharging battery packs. Double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".}} | |||
* {{Red|Do not mix and use old batteries with new batteries, or batteries with different brand names.}} | |||
* {{Red|Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.}} | |||
* {{Red|When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.}} | |||
* {{Red|Keep the UPS shield away from children to ensure their safety.}} | |||
==Overview== | ==Overview== | ||
The '''X1209''' is a dedicated UPS expansion board for the Raspberry Pi, delivering reliable '''5.1V/6000mA backup''' power to ensure uninterrupted operation. It is designed to support demanding setups, including those running intensive applications or multiple peripherals. | The '''X1209''' is a dedicated UPS expansion board for the Raspberry Pi, delivering reliable '''5.1V/6000mA backup''' power to ensure uninterrupted operation. It is designed to support demanding setups, including those running intensive applications or multiple peripherals. | ||
| Line 6: | Line 25: | ||
Additionally, the X1209 offers fast charging up to 2100mA for quick battery replenishment and integrates seamlessly with compatible storage products for reliable data backup during power loss. This combination of features enhances system reliability, protects valuable data, and ensures continuous operation for Raspberry Pi users. | Additionally, the X1209 offers fast charging up to 2100mA for quick battery replenishment and integrates seamlessly with compatible storage products for reliable data backup during power loss. This combination of features enhances system reliability, protects valuable data, and ensures continuous operation for Raspberry Pi users. | ||
{{Raspberry Pi 5 UPS Sets}} | |||
==Features== | ==Features== | ||
| Line 16: | Line 38: | ||
'''UPS Output''' | '''UPS Output''' | ||
* Designed for continuous long-duration operation (duration depends on battery type and applications) | * Designed for continuous long-duration operation (duration depends on battery type and applications) | ||
* Supports a maximum current output of 5.1V 6000mA, suitable for most Raspberry Pi applications | * Supports a '''maximum current output of 5.1V 6000mA''', suitable for most Raspberry Pi applications | ||
* Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss | * Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss | ||
* Power the Pi directly through the 40-pin header, eliminating the need for cables and soldering | * Power the Pi directly through the 40-pin header, eliminating the need for cables and soldering | ||
* Equipped with XH2.54 connectors for 5V power output | * Equipped with '''XH2.54 connectors for 5V power output''' | ||
'''Battery Charging''' | '''Battery Charging''' | ||
| Line 32: | Line 54: | ||
'''Power Input''' | '''Power Input''' | ||
* Integrated high-efficiency step-down DC-DC converter | * Integrated high-efficiency step-down DC-DC converter | ||
* Wide operating input range of 6V to 18V | * Wide operating '''input range of 6V to 18V''' | ||
* Provides up to 6A output current, enabling 2.1A fast charging while powering the system | * Provides '''up to 6A output current, enabling 2.1A fast charging''' while powering the system | ||
* Allows power input from various sources such as a car, solder panel, and more | * Allows power input from various sources such as a car, solder panel, and more | ||
* Common power input jack size of 5.5x2.1mm | * '''Common power input jack size of 5.5x2.1mm''' | ||
* Compatible with Raspberry Pi USB-C Power Supply | * '''Compatible with Raspberry Pi USB-C''' Power Supply | ||
'''Enhanced Power Management''' | '''Enhanced Power Management''' | ||
* Seamless power switching between backup power and power adapter | * Seamless power switching between backup power and power adapter | ||
* On-board push button performs the same actions as the Pi's power button (Pi 5 only) | * '''On-board push button''' performs the same actions as the Pi's power button (Pi 5 only) | ||
* Automatically cuts off power when the Pi is shut down | * '''Automatically cuts off power when the Pi is shut down''' | ||
* On-board LED indicates power status and Pi detection | * On-board '''LED indicates''' power status and Pi detection | ||
* AC power loss and power adapter failure detection via GPIO | * '''AC power loss and power adapter failure detection''' via GPIO | ||
* Auto power-on when power is applied or restored | * '''Auto power-on''' when power is applied or restored | ||
* Automatic safe shutdown when battery voltage is low (programmable) | * '''Automatic safe shutdown''' when battery voltage is low (programmable) | ||
* Ultra-low standby power consumption to maximize battery life | * Ultra-low standby power consumption to maximize battery life | ||
* Advanced system power-path management to minimize frequent charging and discharging of batteries | * Advanced system power-path management to minimize frequent charging and discharging of batteries | ||
| Line 59: | Line 81: | ||
|'''Technical Specification''' || | |'''Technical Specification''' || | ||
'''Power input:''' | '''Power input:''' | ||
* 6-18Vdc via DC jack (12Vdc ≥3A power adapter recommended) | * {{Red|6-18Vdc via DC jack}} (12Vdc ≥3A power adapter recommended) | ||
* 5Vdc 5A via USB-C | * {{Red|5Vdc 5A via USB-C}} | ||
'''UPS output:'''5.1V ±5% Max 6A | '''UPS output:'''5.1V ±5% Max 6A | ||
'''Battery charging current:'''2.1A | '''Battery charging current:''' 2.1A {{Red|(IMPORTANT !!-- Please confirm before connecting your battery.)}} | ||
'''Terminal Battery Voltage:''' 4.23V | '''Terminal Battery Voltage:''' 4.23V {{Red|(IMPORTANT !!-- Please confirm before connecting your battery.)}} | ||
'''Battery Recharge Threshold:''' 4.1V | '''Battery Recharge Threshold:''' 4.1V | ||
'''Battery:''' 3.7V Lithium Battery {{Red|(IMPORTANT !!-- Only parallel connection is supported, please check polarity of battery's connector to make sure "+" to "+" and "-" to "-". Connecting batteries in series will cause the X1209 to burn out!)}} | |||
'''Ports & Connectors:''' | '''Ports & Connectors:''' | ||
| Line 77: | Line 102: | ||
* 40-pin extended GPIO header x1 | * 40-pin extended GPIO header x1 | ||
PCB Size: 65mm x 57mm | |||
'''PCB Size:''' 65mm x 57mm | |||
|- | |- | ||
| '''Notes''' || | | '''Notes''' || | ||
* | * {{Red|Do not apply power to your Raspberry Pi via the USB C socket.}} | ||
|} | |} | ||
| Line 87: | Line 113: | ||
* Spacer M2.5 F/F 13.5mm x4 | * Spacer M2.5 F/F 13.5mm x4 | ||
* Screw M2.5x5mm x8 | * Screw M2.5x5mm x8 | ||
* Pogo pin x1 (For use with Pi 5 only) | * Pogo pin x1 (For use with Pi 5 only) | ||
[[File:X1209-IMG-0015-Packing-List.jpg|700px]] | |||
==Script Reference== | |||
{{X120x Series UPS Script Reference}} | |||
==Matching Case== | |||
No matching case yet. | |||
==User Manual== | ==User Manual== | ||
* Hardware Installation: | * Hardware Installation: [https://suptronics.com/Raspberrypi/Power_mgmt/x1209-v1.0_hardware.html X1209 Hardware] | ||
* How to make it work: | * How to make it work: [[#Script Reference]] | ||
==FAQ== | ==FAQ== | ||
<div class="toccolours mw-collapsible mw-collapsed"> | <div class="toccolours mw-collapsible mw-collapsed"> | ||
<div style="font-weight:bold;line-height:1.0;"> | <div style="font-weight:bold;line-height:1.0;"> | ||
Q1: | Q1: What types of batteries are compatible with the X1209 UPS board? | ||
</div> | </div> | ||
<div class="mw-collapsible-content"> | <div class="mw-collapsible-content"> | ||
A: | A: The X1209 is compatible with 3.7V-rated batteries, such as 18650, 21700, 4680, and similar types, as long as they have a full charge voltage of 4.2V. | ||
The default charging current is set to 2.1A and the charge cut-off voltage is 4.23V. Before connecting your battery to the UPS board, please carefully confirm the maximum charging current and voltage; exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage. | |||
</div> | </div> | ||
</div> | </div> | ||
<div class="toccolours mw-collapsible mw-collapsed"> | |||
<div style="font-weight:bold;line-height:1.0;"> | |||
Q2: Is the X1209 compatible with Raspberry Pi Zero 2W? | |||
</div> | |||
<div class="mw-collapsible-content"> | |||
A: Yes. The X1209 UPS board can work with Raspberry Pi Zero 2W according to the customer feedback. | |||
However, the X1209 was originally designed for the standard Raspberry Pi 40-pin layout. When using it with the Raspberry Pi Zero 2W, you may need to connect it via jumper wires or use a suitable adapter/pin header to match the GPIO power pins. | |||
</div> | |||
</div> | |||
<!--Add review function! --> | <!--Add review function! --> | ||
< | <comment-streams id="main" /> | ||
<!--Please choose the --> | <!--Please choose the --> | ||