X1500: Difference between revisions
Replace <comments/> with <comment-streams /> |
|||
| (25 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
{{GD Template Impl}} | {{GD Template Impl}} | ||
[[File: X1500-IMG-9222-Interface.jpg | right |thumb|X1500 CM5 IO Board - Interface]] | [[File: X1500-IMG-9222-Interface.jpg | right |thumb|X1500 CM5 IO Board - Interface]] | ||
[[File:X1500-IMG-9213-J2-J6-GPIO-FAN.jpg|thumb|right|X1500 Pin Header]] | |||
[[File: X1500-IMG-9216-SSDs.jpg | right |thumb|X1500 CM5 IO Board - Support Dual NVMe SSDs]] | [[File: X1500-IMG-9216-SSDs.jpg | right |thumb|X1500 CM5 IO Board - Support Dual NVMe SSDs]] | ||
[[File: X1500-IMG-9227-Single-Board.jpg | right |thumb|X1500 CM5 IO Board]] | [[File: X1500-IMG-9227-Single-Board.jpg | right |thumb|X1500 CM5 IO Board]] | ||
| Line 28: | Line 29: | ||
* '''Dual USB 3.2 Gen 1 Ports''': delivering high-speed data transfer rates of up to 5 Gbps. <span class="tb_red">USB 3.0 = USB 3.2 Gen 1 (identical specs)</span> | * '''Dual USB 3.2 Gen 1 Ports''': delivering high-speed data transfer rates of up to 5 Gbps. <span class="tb_red">USB 3.0 = USB 3.2 Gen 1 (identical specs)</span> | ||
* '''Dual MIPI DSI/CSI-2 Connectors''': 22-pin FPC connectors (0.5mm pitch) compatible with Raspberry Pi 5 CSI and DSI modules for seamless camera and display integration. | * '''Dual MIPI DSI/CSI-2 Connectors''': 22-pin FPC connectors (0.5mm pitch) compatible with Raspberry Pi 5 CSI and DSI modules for seamless camera and display integration. | ||
CAM/DISP 0 supports both displays or cameras. CAM/DISP 0 supports using a signal to power down the camera to save power. CAM/DISP 1 typically needs two jumpers fitting to '''J6''' to route the I2C signals | CAM/DISP 0 supports both displays or cameras. CAM/DISP 0 supports using a signal to power down the camera to save power. CAM/DISP 1 typically needs two jumpers fitting to '''J6''' to route the I2C signals from the GPIO connector to the camera connector. CAM/DISP 1 can be used with displays and cameras. If it is used with a camera, it isn’t possible to power down the camera. Also refer to [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf Raspberry Pi Compute Module 5 IO Board datasheet (Page 5)] | ||
* '''MicroSD Card Slot''': Supports Compute Module 5 Lite variants (without onboard eMMC) | * '''MicroSD Card Slot''': Supports Compute Module 5 Lite variants (without onboard eMMC) | ||
* '''Raspberry Pi HAT+ Compatibility''': Reuse existing Raspberry Pi HATs to save time and reduce development costs. | * '''Raspberry Pi HAT+ Compatibility''': Reuse existing Raspberry Pi HATs to save time and reduce development costs. | ||
| Line 34: | Line 35: | ||
* '''RTC Battery Socket (CR1220 coin battery is not included)''': Ensures accurate timekeeping during power interruptions. | * '''RTC Battery Socket (CR1220 coin battery is not included)''': Ensures accurate timekeeping during power interruptions. | ||
* '''PWM Fan Support''': Includes a fan power connector for adjustable cooling in demanding environments. | * '''PWM Fan Support''': Includes a fan power connector for adjustable cooling in demanding environments. | ||
* '''USB-C Port''': Handles both power delivery and OS image loading directly into the CM5’s eMMC. | * '''USB-C Port''': Handles both power delivery and OS image loading directly into the CM5’s eMMC.(<span class="tb_red">The OTG port is generally used for flashing the eMMC. If it's used for other purposes, power should be supplied via the 40-pin header—just like the official CM5 IO board.</span>) | ||
* '''Configurable Jumpers''': Allows disabling features like wireless connectivity or EEPROM writing for customization. | * '''Configurable Jumpers''': Allows disabling features like wireless connectivity or EEPROM writing for customization. | ||
* '''Streamlined Connector Layout''': USB, HDMI, Ethernet, and power ports are grouped along one edge for clean cable management and easy enclosure integration. | * '''Streamlined Connector Layout''': USB, HDMI, Ethernet, and power ports are grouped along one edge for clean cable management and easy enclosure integration. | ||
* '''40-Pin GPIO header''': Uses the same GPIO pinout as the Raspberry Pi 5 | |||
|- | |- | ||
| '''Technical Specification''' || | | '''Technical Specification''' || | ||
| Line 70: | Line 72: | ||
<span class="tb_red">For optimal performance, please use the official Raspberry Pi '''27W USB-C''' Power Supply or an alternative power supply capable of delivering '''5.1V at 5A'''. An incompatible power supply with a lower output voltage may fail to power on the system.</span> | <span class="tb_red">For optimal performance, please use the official Raspberry Pi '''27W USB-C''' Power Supply or an alternative power supply capable of delivering '''5.1V at 5A'''. An incompatible power supply with a lower output voltage may fail to power on the system.</span> | ||
|} | |} | ||
==User Manual== | |||
* The hardware design refers to the official design, please refer to: https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf | |||
* '''Hardware Installation: [https://suptronics.com/Raspberrypi/cm5/x1500-v1.0_hardware.html X1500 Hardware]''', <span class="tb_red">'''please click the left link to view it, it's very important!''' </span> | |||
* '''How to make it work: [https://suptronics.com/Raspberrypi/cm5/x1500-v1.0_software.html X1500 Software]''', <span class="tb_red">'''please click the left link to view it, it's very important!''' </span> | |||
* You can also refer to the [https://datasheets.raspberrypi.com/cm5/cm5io-datasheet.pdf official CM5 IO board] of the Raspberry Pi Foundation. The usage of X1500 is the same as it. | |||
* https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage | |||
* how to flash os into cm5 emmc, Refer to the following: | |||
#https://smarthomecircle.com/how-to-install-os-on-raspberry-pi-compute-module-5-emmc-storage | |||
#https://www.youtube.com/watch?v=SWv-WYlHJWQ | |||
* Configuration steps for using an external antenna: | |||
https://www.raspberrypi.com/documentation/computers/compute-module.html#antenna | |||
==Packing List== | |||
* X1500 V1.0 CM5 carrier board x 1 | |||
* M.2-A1 extension board x 2 (to fix M.2 2230 and 2242 SSDs) | |||
* 2.54mm jumer cap x 2 | |||
* M2*3 screw x 6 | |||
[[File: X1500-Packing-List.jpg|800px]] | |||
==Matching Case== | ==Matching Case== | ||
According to user feedback, we have designed a metal case [[ | According to user feedback, we have designed a metal case [[X1500-C1]] / [[X15-C1]] specifically for [[X1500]] / [[X1501]] IO boards. [[X15-C1]] and [[X1500-C1]] have different sizes, different appearances, and the same usage. | ||
Here is a detailed comparison: | |||
{| class="wikitable" | {| class="wikitable" | ||
! Model !! Compatible with !!compatibility!!Cooler | ! Model !! Compatible with !!compatibility!!Cooler / Heatsink | ||
|- | |- | ||
| [[X15-C1]] V1.0 ||Raspberry Pi CM5||[[X1500]]/[[X1501]]/other low-profile expansion HATs||[[X15- | | [[X15-C1]] V1.0 ||Raspberry Pi CM5||[[X1500]]/[[X1501]]/other low-profile expansion HATs||[[X15-F1]] | ||
|- | |- | ||
| [[X1500-C1]] ||Raspberry Pi CM5||[[X1500]]/[[X1501]]||[[C519]] | | [[X1500-C1]] ||Raspberry Pi CM5||[[X1500]]/[[X1501]]||[[C519]] | ||
| Line 83: | Line 106: | ||
'''Please note''': The metal case will shield the wifi signal, so please use Ethernet when you use this case | '''Please note''': The metal case will shield the wifi signal, so please use Ethernet when you use this case | ||
<gallery> | |||
X15-C1-IMG-9680.jpg|X15-C1 | |||
X1500-C1-IMG-9275-NEW.jpg|X1500-C1 | |||
File:X1500-C2-IMG-9819.jpg|X1500-C2 | |||
</gallery> | </gallery> | ||
== | ==Installation Tips for C519 & X1500/X1501== | ||
Since both the C519 heatsink and PCB holes are threaded, proper alignment and minimal spacing are crucial during assembly. Carefully align the C519 with the PCB mounting holes, press down firmly until the heatsink touches the PCB, then tighten the screws. | Since both the C519 heatsink and PCB holes are threaded, proper alignment and minimal spacing are crucial during assembly. Carefully align the C519 with the PCB mounting holes, press down firmly until the heatsink touches the PCB, then tighten the screws. | ||
| Line 120: | Line 128: | ||
Installation Video: https://youtu.be/H1vgT2lrJQI | Installation Video: https://youtu.be/H1vgT2lrJQI | ||
{{#ev:youtube|https://youtu.be/H1vgT2lrJQI}} | {{#ev:youtube|https://youtu.be/H1vgT2lrJQI}} | ||
==FAQ== | ==FAQ== | ||
| Line 136: | Line 133: | ||
<!--Add review function! --> | <!--Add review function! --> | ||
< | <comment-streams id="main" /> | ||
<!--Please choose the --> | <!--Please choose the --> | ||