X1200: Difference between revisions

(20 intermediate revisions by 5 users not shown)

Line 1:

[[File:X1200-V1.2-IMG-7240-Interface-NEW.jpg|thumb|right|X1200 V1.2 Interface Schematic]]

[[File:X1200-V1.1-Overview.jpg|thumb|right|X1200 ~~V1.2 Interface Schematic~~]]

[[File:X1200-V1.1-Overview.jpg|thumb|right|X1200 pogo pins]]

[[File:X1200-V1.2-IMG-7235.jpg|thumb|right|X1200 V1.2]]

[[File:X1200-V1.2-IMG-7239.jpg|thumb|right|X1200 V1.2]]

[[File:X1200-V1.2-IMG-7220.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5]]

[[File:X1200-V1.2-IMG-7239-BAT.jpg|thumb|right|X1200 Raspberry Pi 5 UPS-Battery Requirement]]

[[File:X1200-V1.2-IMG-7222.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5]]

[[File:X1200-V1.2-IMG-7228.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5 & Active Cooler]]

==Safety Instructions & Warnings==

* It is essential to read and understand these safety instructions and warnings before charging your batteries.

* Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.

* Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".

* Do not mix and use old batteries with new batteries, or batteries with different brand names.

* Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.

* When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS ~~shield on wood material or carpet unattended.~~

* Keep the UPS shield away from children to ensure their safety.

* Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/

* Battery Recommend for Geekworm UPS board, please refer to: [[File:NCR18650B.pdf|X728 battery recommend]]

==Overview==

X1200 is an innovative uninterruptible power supply (UPS) expansion board designed specifically for the Raspberry Pi 5. With its advanced features and robust power backup capabilities, the X1200 is perfect for even the most demanding Raspberry Pi setups.

'''Please note:''' If the UPS does not detect the RPi5, it will automatically shut down within 3 seconds. So you need to install the RPi 5 on the UPS and make sure that the RPi5 has good contact with the UPS's pogo pins.

Line 114:

Line 109:

* CM2.5 x 4 screws x 4

[[File:X1200-V1.2-IMG-7239-packing-list.jpg | 600px]]

==Script Reference==

==User Manual==

~~===Dimensions source file (DXF)===~~

* Dimensions source file (DXF): [[File:X1200-pcb-v1.dxf]] - You can view it with [https://viewer.autodesk.com/ Autodesk Viewer] online

~~===X1200 Hardware===~~

* X1200 Hardware: [[X1200 Hardware]]

~~===X1200 Software===~~

* How to get x1200 work: [[#Script Reference]]

* ~~X1200 Software~~: [~~https~~:~~//suptronics.com/Raspberrypi/Power_mgmt/x120x~~-v1.~~0_software.html X1200 Software~~]

* Low voltage warning solution for X120x Series UPS:

~~===~~Installation Guide~~===~~

[[File:IMG-7278-Low-Voltage.jpg | 700px]]

* Installation Guide

[[File:007-X1200-C1-IMG-8206-installation.jpg | 700px]]

Line 130:

Line 127:

==Matching Case==

X1200-C1 is a metal case '''for Raspberry Pi 5 & X1200''' UPS Shield, it also support installing active cooler and Raspberry Pi 5 PIP PCIe to M2 NVMe Shield like [[X1001]], [[X1004]], [[X1003]], [[X1000]] and [[M901]] on the top of Raspberry Pi 5.

* Case dimensions: 90.8 x 69 x 62.8 mm / 3.57 x 2.72 x 2.47 inches

* Note: On 12 March 2025, we updated the X1200-C1 case to '''add a row of cooling holes''' on the TF card slot side to '''increase airflow and take more advantage of the Raspberry Pi 5 active heatsink'''.

*Note: If you only need to use the X1200-C1 with the Raspberry Pi 5 motherboard (without the X1200 UPS board), you can separately add 4 M2.5*6+5 screws (or directly use M2.5*27 copper standoffs) to achieve the ideal installation.

X1200-C1-IMG-8145-Packing-List.jpg | X1200-C1 Accessories

Line 139:

Line 136:

004-X1200-C1-IMG-8137-Interface.jpg |Interface-Rear

005-X1200-C1-IMG-8140-size.jpg|X1200-C1 Dimension

</gallery>

Line 145:

Line 143:

<~~comments~~ />

<comment-streams id="main" />

@@ Line 1: / Line 1: @@
 {{GD Template Impl}}
 [[File:X1200-V1.2-IMG-7240-Interface-NEW.jpg|thumb|right|X1200 V1.2 Interface Schematic]]
-[[File:X1200-V1.1-Overview.jpg|thumb|right|X1200 V1.2 Interface Schematic]]
+[[File:X1200-V1.1-Overview.jpg|thumb|right|X1200 pogo pins]]
 [[File:X1200-V1.2-IMG-7235.jpg|thumb|right|X1200 V1.2]]
 [[File:X1200-V1.2-IMG-7239.jpg|thumb|right|X1200 V1.2]]
 [[File:X1200-V1.2-IMG-7220.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5]]
+[[File:X1200-V1.2-IMG-7239-BAT.jpg|thumb|right|X1200 Raspberry Pi 5 UPS-Battery Requirement]]
 [[File:X1200-V1.2-IMG-7222.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5]]
 [[File:X1200-V1.2-IMG-7228.jpg|thumb|right|X1200 V1.2 with Raspberry Pi 5 & Active Cooler]]
 ==Safety Instructions & Warnings==
-* <span style="color:red;">It is essential to read and understand these safety instructions and warnings before charging your batteries.
+{{UPS Safety Warning}}
-* <span style="color:red;">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.
-* <span style="color:red;">Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
-* <span style="color:red;">Do not mix and use old batteries with new batteries, or batteries with different brand names.
-* <span style="color:red;">Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.
-* <span style="color:red;">When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.
-* <span style="color:red;">Keep the UPS shield away from children to ensure their safety.
-* Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/
-* Battery Recommend for Geekworm UPS board, please refer to: [[File:NCR18650B.pdf|X728 battery recommend]]
 ==Overview==
 X1200 is an innovative uninterruptible power supply (UPS) expansion board designed specifically for the Raspberry Pi 5. With its advanced features and robust power backup capabilities, the X1200 is perfect for even the most demanding Raspberry Pi setups.
+'''Please note:''' If the UPS does not detect the RPi5, it will automatically shut down within 3 seconds. So you need to install the RPi 5 on the UPS and make sure that the RPi5 has good contact with the UPS's pogo pins.
 {{Raspberry Pi 5 UPS Sets}}
@@ Line 114: / Line 109: @@
 * CM2.5 x 4 screws x 4
 [[File:X1200-V1.2-IMG-7239-packing-list.jpg | 600px]]
+==Script Reference==
+{{X120x Series UPS Script Reference}}
 ==User Manual==
-===Dimensions source file (DXF)===
 * Dimensions source file (DXF): [[File:X1200-pcb-v1.dxf]] - You can view it with [https://viewer.autodesk.com/ Autodesk Viewer] online
-===X1200 Hardware===
 * X1200 Hardware: [[X1200 Hardware]]
-===X1200 Software===
+* How to get x1200 work: [[#Script Reference]]
-* X1200 Software: [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software]
+* Low voltage warning solution for X120x Series UPS:
-===Installation Guide===
+[[File:IMG-7278-Low-Voltage.jpg | 700px]]
+* Installation Guide
 [[File:007-X1200-C1-IMG-8206-installation.jpg | 700px]]
@@ Line 130: / Line 127: @@
 ==Matching Case==
 X1200-C1 is a metal case '''for Raspberry Pi 5 & X1200''' UPS Shield, it also support installing active cooler and Raspberry Pi 5 PIP PCIe to M2 NVMe Shield like  [[X1001]], [[X1004]], [[X1003]], [[X1000]] and [[M901]] on the top of Raspberry Pi 5.
 * Case dimensions: 90.8 x 69 x 62.8 mm / 3.57 x 2.72 x 2.47 inches
+* Note: On 12 March 2025, we updated the X1200-C1 case to '''add a row of cooling holes''' on the TF card slot side to '''increase airflow and take more advantage of the Raspberry Pi 5 active heatsink'''.
+*Note: If you only need to use the X1200-C1 with the Raspberry Pi 5 motherboard (without the X1200 UPS board), you can separately add 4 M2.5*6+5 screws (or directly use M2.5*27 copper standoffs) to achieve the ideal installation.
 <gallery>
 X1200-C1-IMG-8145-Packing-List.jpg | X1200-C1 Accessories
@@ Line 139: / Line 136: @@
 -X1200-C1-IMG-8137-Interface.jpg |Interface-Rear
 -X1200-C1-IMG-8140-size.jpg|X1200-C1 Dimension
 </gallery>
@@ Line 145: / Line 143: @@
 <!--Add review function! -->
-<comments />
+<comment-streams id="main" />
 <!--Please choose the  -->