Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 23:34, 17 October 2024 46.138.82.4 talk posted a new comment on X1202 ("Capacity: 8.34% (Medium), AC Power State: Unplugged, Voltage: 3.67V Battery level critical." But 3 green LEDs are on)
  • 17:51, 17 October 2024 46.138.82.4 talk posted a new comment on X1202 ("Capacity: 65.42% (Full), AC Power State: Unplugged, Voltage: 3.90V UPS is unplugged or AC power loss detected." If I connect POE via x1012 to rpi5 with x1202, it seems like the adapter is not connected, but 4 green LEDs are on. Is it ok or something wrong?)
  • 23:15, 16 October 2024 128.2.149.101 talk posted a new comment on X-UPS1 (In addition to the previous question: I plan to use two of these UPS boards, stacked together whole having power input (12V 10A) power supply connected for most of the time. The idea is to continue provide power to the 12V 4A motor, even when the power supply is disconnected. Will this work? With the power input connected, if the output side is drawing 4A, it can still draw 4A from the power supply, right?)
  • 22:33, 16 October 2024 128.2.149.101 talk posted a new comment on X-UPS1 (Also, my current plan is to use two of these UPS board, stacked together to provide UPS capability to a 12v 4a motor, will there be any issue? Also if the system is not powered, and I turn the motor, the motor generate power. Does the board protect against any "backward" current produced by rotating the downstream motor??)
  • 00:38, 16 October 2024 128.2.149.101 talk posted a new comment on X-UPS1 (Following the previous question: If I stack 2 of these boards together: I know output current is subject to the quantity of boards. But can I use 12V output (VH3.96 x 2) port coming out from both boards, so (VH3.96 x 4) all at once to get the full current output?)
  • 14:15, 15 October 2024 Lisa talk contribs posted a new comment on NASPi CM4-M2 (Hi,it's only support 3pin Fan； you can use a [4010 Fan-3Pin PWM Fan with Bracket] instead of C235 heastsink; https://geekworm.com/products/dc-5v-30mm-40mm-50mm-60mm-cooling-fan?variant=40016674324568 If you buy it in our store, please leave a message in the order and we will provide you with the suitable screws and spacers.)
  • 12:05, 15 October 2024 Lisa talk contribs posted a new comment on X-UPS1 (Hi， 1）All power input are connected together via the 18-pin female header,no need to power both boards at the same time. 2）output current is subject to the quantity of boards.)
  • 03:39, 15 October 2024 128.2.149.101 talk posted a new comment on X-UPS1 (If I stack 2 of these boards together. 1) Can I supply power input through both the DC barrel connectors on both boards when stacked? 2) Can I use 12V output from both boards, to get the full current output? 3A x 2boards?)
  • 23:34, 14 October 2024 155.31.35.78 talk posted a new comment on EDP to HDMI Adapter (I'm still trying to figure out how to plug in the edp cable into the board. Every time the wire makes contact, the board heats up and burns.)
  • 22:07, 14 October 2024 124.244.111.67 talk posted a new comment on NASPi CM4-M2 (How to connect a 4-pin PMW fan to the board? Please help. NASPi is very hot, always keep in 70c. Passive cooling is not practical for a NAS server.)
  • 14:34, 14 October 2024 185.7.196.6 talk posted a new comment on X1011 (Same for me - doesn't work)
  • 12:23, 14 October 2024 Harry talk contribs posted a new comment on X-UPS1 (* LBAT: A high level will be triggered when the battery voltage is lower than or equal to 3V (You can't modify this threshold of 3V) * PLD: (AC power loss detection), When the external power supply is disconnected, it will trigger a high level, and the indicator light will be on It is clearly written here.)
  • 10:55, 14 October 2024 Harry talk contribs posted a new comment on X1011 (Please contact us via mail)
  • 10:54, 14 October 2024 Harry talk contribs posted a new comment on X1011 (X1011 does not support hardware RAID, please start with software)
  • 10:42, 14 October 2024 Lisa talk contribs posted a new comment on X306 (The 4-pin header cannot be used as a power supply. please refer to the [4 Pin header function description])
  • 01:54, 14 October 2024 185.78.11.142 talk posted a new comment on X1011 (Update, I have change from the RPi 25w USB PSU to a 50w PSU direct to the x1011. I am using Open Media Vault and when a drive disappears it comes back after a reboot and after a second reboot the RAID 5 array is "clean" again...)
  • 04:38, 13 October 2024 45.88.221.129 talk posted a new comment on X-UPS1 (Can you please explain how to wire a LED to the PLD LBAT port?) Tags: Mobile web edit, Mobile edit
  • 20:19, 12 October 2024 37.201.213.105 talk posted a new comment on X306 (I have soldered the 4-pin header in. I want to use the 4-pin header as a power supply instead of the pogo pins. The 4-pin header does only deliver 3.3V. The pogo pins deliver 5V. Is there a way for the 4-pin header do deliver 5V?)
  • 11:26, 12 October 2024 Lisa talk contribs posted a new comment on X306 (X306 V1.3 has removed the 4Pin header, do you want to solder it to connect a power switch?)
  • 17:22, 11 October 2024 37.201.213.105 talk posted a new comment on X306 (I still would like to know the answer to my question, please.)
  • 21:08, 10 October 2024 94.134.28.144 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (WD Blue SN580 NVMe SSD out of the Box running (Anonymous user #13 think you are right meant is Blue not Green:) WD Blue SN580 running on M1001 V2(one LED),Bookworm Lite (apt update&&apt upgrade),newest Bootloader. pi5:~ $ sudo lspci 0000:00:00.0 PCI bridge... 0000:01:00.0 Non-Volatile memory controller: Sandisk Corp WD Blue SN580 NVMe SSD (DRAM-less) (rev 01) 0001:00:00.0 PCI bridge... 0001:01:00.0 Ethernet... --- pi5:/mnt/nvmep1 $ vcgencmd bootloader_version 2024/09/23 14:02:56 ... --- pi5:/...)
  • 10:31, 10 October 2024 Lisa talk contribs posted a new comment on X1201 (Hi,X1201 UPS not support Pi4;you may consider using X-UPS1)
  • 02:41, 10 October 2024 185.72.234.55 talk posted a new comment on X1001 (Hi, what is the difference between the M901 and X1001, other than the mounting style?)
  • 01:32, 10 October 2024 201.110.169.216 talk posted a new comment on X1201 (Would it work with a Raspberry Pi 4? I know there are specific UPS boards for RPi4, but I'm looking into building a cluster case for a mix of RPi5s and RPi4sm and would like to standarize the build/footprint)
  • 00:57, 9 October 2024 78.42.87.196 talk posted a new comment on X1012 (Patriot [P320] 128GB - P320P128GM28 is working fine - hdparm 398.24 mb/s Kioxa ssd from steam deck isnt working because of M/B-Key, you need a M-Key NVME PCIe SSD)
  • 23:27, 8 October 2024 185.78.11.142 talk posted a new comment on X1011 (I have one of these with 4 SSD and it works fine when all drives are separate but as soon as I run them in RAID5 one drive fails. It always seems to be the drive in slot 2 that fails even when I swap them round.)
  • 17:30, 5 October 2024 Lisa talk contribs posted a new comment on X-UPS1 (Hi，The height of the expansion board with battery is about 21mm; the distance between the first and second layers is 25mm.)
  • 17:17, 5 October 2024 Lisa talk contribs posted a new comment on X1001 (Hello，Sorry, we haven't tested the Crucial P3 Plus; if you already have this SSD, you can test it. If you need to buy an SSD, please refer to here (the models we tested)：https://geekworm.com/products/colorful-cn600-pcie3-m2-nvme or refer to our customer's test video to select a compatible SSD.X1001#User Manual--Which NVMe drives work with a Raspberry Pi 5?)
  • 17:17, 5 October 2024 Lisa talk contribs deleted comment #5187 on X1001
  • 17:17, 5 October 2024 Lisa talk contribs posted a new comment on X1001 (Hello，Sorry, we haven't tested the Crucial P3 Plus; if you already have this SSD, you can test it. If you need to buy an SSD, please refer to here (the models we tested)：https://geekworm.com/products/colorful-cn600-pcie3-m2-nvme or refer to our customer's test video to select a compatible SSD.X1001#User Manual--Which NVMe drives work with a Raspberry Pi 5?)
  • 21:17, 4 October 2024 131.100.39.240 talk posted a new comment on X-UPS1 (What is the height of the board with batteries ?) Tags: Mobile web edit, Mobile edit
  • 20:25, 4 October 2024 163.116.212.48 talk posted a new comment on X1001 (Hello, so i have a Raspberry Pi 5 with a Geekworm X1001 PCIe to M.2 Key-M NVMe SSD PIP TOP, is Crucial P3 Plus 1TB PCIe Gen4 NVMe M.2 SSD compatible with x1001? Thanks.)
  • 18:16, 4 October 2024 Lisa talk contribs posted a new comment on X1012 (Sorry, only incompatible lists are available right now.If you want to buy an M.2 NVMe 2280 SSD, please refer to this link https://geekworm.com/products/colorful-cn600-pcie3-m2-nvme; this is the one we tested.)
  • 11:34, 4 October 2024 218.253.67.126 talk posted a new comment on X1012 (Is there a list of compatible SSD models somewhere? (instead of having people watching videos, a official list would be much better))
  • 18:23, 3 October 2024 14.153.79.53 talk posted a new comment on X1202 (One more thing you need to consider is to think about the conversion rate of UPS HAT, which is usually around 85%.)
  • 17:21, 3 October 2024 Lisa talk contribs posted a new comment on X1012 (Hello，Sorry, we haven't tested Kioxia; you can refer to our customer's test video to select a compatible SSD.X1001#User Manual--Which NVMe drives work with a Raspberry Pi 5?)
  • 17:07, 3 October 2024 Lisa talk contribs posted a new comment on NESPi Pro (Button battery, if you have already purchased this case, you can look at the specifications of the button battery interface on the case.)
  • 17:04, 3 October 2024 Lisa talk contribs posted a new comment on X1203 (This depends on the battery capacity you use and the load requirements.)
  • 16:37, 3 October 2024 213.249.56.36 talk posted a new comment on NESPi Pro (What type of battery is needed?)
  • 03:43, 3 October 2024 198.44.128.154 talk posted a new comment on X1203 (Are two 3.7V batteries required to power the full 5A output?)
  • 18:41, 2 October 2024 143.93.117.10 talk posted a new comment on X1001 (We have tested two SSDs with the X1002. One works (Intenso M.2 SSD Premium) one does not (Kensington NV2 PCIe 4.0). Both are 256GB models.)
  • 16:43, 2 October 2024 218.253.67.126 talk posted a new comment on X1012 (Hi, can I use Kioxia SD10 SSD with this?)
  • 05:47, 2 October 2024 73.171.253.198 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (For those looking for info on the mzp280v00br with the pi zero w: Use the legacy pi os install through the Raspberry P Imager. Enable the legacy Gl driver in raspi-config. I used the 32 bit os as I was on the pi zero. This is the only os that worked. Have fun!)
  • 03:01, 1 October 2024 86.87.123.160 talk posted a new comment on X1202 (Hello, I have 4 batteries, each with a capacity of 2980mAh. The total capacity is therefore 4x2980mAh=11920mAh. With the Raspberry running my application I measured it draws 700mA. So 11920mAh / 700mA = approx 17 hours of running time. Can someone confirm this? Thanks in advance.)
  • 22:44, 30 September 2024 185.50.233.235 talk posted a new comment on X1202 (Actually I see it in the interface picture, point 6: 5VO power output LED: if the Pi 5 is not detected, will turn on for 3 second then off. Does it mean then that the output USB gives continuous power for 3 seconds after the RPI shuts down? Is the powering of the USB output seamless till switch off?)
  • 22:32, 30 September 2024 185.50.233.235 talk posted a new comment on X1202 (Hi! Could I use the USB output to power up a USB hub? In the interface picture it says: 5V, current unlimited, but down in the user manual it says: USB2.0 type-A power output socket, which implies 5V 500mA, which would be not enough I guess. The use case is that the RPI cuts the power on its usb 3.0 ports at shutdown too soon, causing an increase of the Unexpected Power Loss SMART counter. Using an active USB hub between the RPI and the USB SSD enclosure solves the problem, but at power los...)
  • 21:42, 29 September 2024 143.244.44.174 talk posted a new comment on X652 (What are all the benefits/use cases of the NVMe? I can store more images and boot from NVMe, but can I screen capture to the NVMe from PiKVM? Anything else?) Tags: Mobile web edit, Mobile edit
  • 18:01, 29 September 2024 Lisa talk contribs posted a new comment on X1100 (Hi， X1100 supports UASP.)
  • 11:52, 29 September 2024 Lisa talk contribs posted a new comment on X1203 (Hello，Sorry, we haven't tested it with the car and can't offer advice. it is recommended to use a case to protect the board and battery if you use it in a car.)
  • 11:52, 29 September 2024 Lisa talk contribs deleted comment #5166 on X1203
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"