Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 18:00, 28 September 2023 Walker talk contribs posted a new comment on NASPi CM4-M2 (Hello, they can be used together)
  • 16:01, 28 September 2023 85.73.187.148 talk posted a new comment on NASPi CM4-M2 (Hello @Geekworm, is it possible to use both ssd slots together??)
  • 14:19, 27 September 2023 Walker talk contribs posted a new comment on LVDS2 (Hello, we recommend that you buy a new LVDS2, I'm sorry)
  • 10:16, 27 September 2023 Walker talk contribs posted a new comment on P173 (Hello, we are using Japanese Shin-Etsu 7921 thermal grease. We have not tested other types of silicone grease.)
  • 02:13, 27 September 2023 195.29.186.242 talk posted a new comment on P173 (Is Arctic AC mx-4 ok for this?)
  • 18:07, 26 September 2023 141.136.192.77 talk posted a new comment on P173 (Which grease to use with copper plate?)
  • 18:03, 26 September 2023 84.199.122.154 talk posted a new comment on LVDS2 (What is the name of component U1 or can you direct me to a datasheet? I applied a too high voltage and it blew up. I want to have a look to replace it.)
  • 10:27, 26 September 2023 Walker talk contribs posted a new comment on X729-Software (Hello, first of all, to run the X729 fan or OLED, you need to run some instructions. For details, you can refer here: [https://wiki.geekworm.com/X729-Software#4._Setting_up_the_PWM_cooling_fan''' ''' fan] [https://wiki.geekworm.com/How_to_enable_OLED_display''' ''' OLED])
  • 10:11, 26 September 2023 Walker talk contribs posted a new comment on NASPi Gemini 3.5 (Hello, you can refer here: https://wiki.geekworm.com/How_to_Configure_RAID_Setting''' ''' Disconnect power supply, and choose your Raid setting, insert or remove jumper by the following jumper instruction: For RAID0 setting, Both A and B jumpers need to be shorted For RAID1 setting, Only the B jumper needs to be shorted For PM setting, No jumpers need to be shorted 700px|none|How to Configure RAID)
  • 00:20, 26 September 2023 192.55.2.36 talk posted a new comment on NASPi Gemini 3.5 (Can you point me to instructions on the power mode switch for the Gemini 3.5? I cannot locate it.)
  • 18:14, 25 September 2023 14.45.239.176 talk posted a new comment on X729-Software (i use raspberry pi4 (OMV) with x729 but not (fan & oled )working. how to run on booting?)
  • 11:38, 25 September 2023 Walker talk contribs posted a new comment on X825 V2.0 (Hello, through the DC 5V power supply port, the X825 board is first powered, and then the PI 4 is powered through the X825. You can refer to the picture below: 700px|none|How-to-Power)
  • 07:21, 23 September 2023 188.148.168.20 talk posted a new comment on X825 V2.0 (When connecting through the 5v dc connector, does that connector power both the sata drive and the Pi4 seprately, or does it power the Pi 4 and then the Pi 4 powers the sata drive through USB?)
  • 11:09, 22 September 2023 Walker talk contribs posted a new comment on LVDS2 (Hello, LVDS2 supports I2S 2-Channel)
  • 10:39, 22 September 2023 Harry talk contribs posted a new comment on DAC II (Hi, Try to select '''R-PIDAC''' in volumio3)
  • 10:03, 22 September 2023 Walker talk contribs posted a new comment on LVDS Adapter (In addition, the resolution must be the VESA standard, and the driver board should be at least V59 grade, or the driver board is not available.)
  • 10:00, 22 September 2023 Walker talk contribs posted a new comment on LVDS Adapter (Hello, this LVDS board is compatible. If there is no HDMI output, it may also be caused by compatibility.)
  • 18:07, 21 September 2023 91.89.130.224 talk posted a new comment on DAC II (I have the same problem that I can't find Aoide DAC II in Volumio 3. When I try with Volumio 2 images from the list I always get the message 'This board requires newer software'. I'm also using a RPi4B.)
  • 17:48, 21 September 2023 202.232.38.130 talk posted a new comment on LVDS2 (Hello, I want to input 3ch I2S signals. Is the input specification of the I2C terminal of this product 1ch?)
  • 11:18, 21 September 2023 73.94.194.27 talk posted a new comment on LVDS Adapter (Hello. I am trying to get output from an industrial machine control that has an LCD panel. I have the v20 board and LVDS2 board but I cannot get either to work. No HDMI output. Any chance this will work with an industrial device or does it have to be a generic driver board? Also, if only 3.3v is being supplied by the driver how should 5v be supplied? Do you have to cut wires?)
  • 09:41, 21 September 2023 Harry talk contribs posted a new comment on NASPi CM4-M2 (Hi, the pwm fan control pin is GPIO18)
  • 00:50, 21 September 2023 87.123.242.79 talk posted a new comment on NASPi CM4-M2 (I'd like to know what are the GPIO Pins of the 3-Pin Fan socket?)
  • 12:19, 19 September 2023 Walker talk contribs posted a new comment on X-UPS1 (Hello, usually between 0-50 degrees)
  • 12:03, 19 September 2023 Walker talk contribs posted a new comment on X708 ("Anonymous user #27", you can contact us via our email: support@geekworm.com we will do our best to solve your problem)
  • 11:59, 19 September 2023 Walker talk contribs posted a new comment on X728 (Thank you for your suggestion, we will take your suggestions into account. Please pay attention to our products if they are updated in the future.)
  • 09:50, 19 September 2023 118.103.93.114 talk posted a new comment on X-UPS1 (Please tell me the operating temperature range and storage temperature range.)
  • 07:16, 19 September 2023 186.84.89.31 talk posted a new comment on X708 (Hello, I need the same. Did they finally help you? Could you help me? I have a Li ion battery in very good condition and at 1% capacity it can work for hours. The capacity reading is wrong.)
  • 23:42, 18 September 2023 5.20.159.89 talk posted a new comment on X728 (It would be a perfect UPS if there was some sort of thermal monitoring present (mainly for safety: stop charging and low and high temp). Please consider adding temperature sensors for batteries in your next board revision.)
  • 12:03, 15 September 2023 Walker talk contribs posted a new comment on XScript (Hello, you can contact us via our email: '''support@geekworm.com ''' ((Please provide your order number)) we will do our best to solve your problem)
  • 09:23, 15 September 2023 Walker talk contribs posted a new comment on PiKVM-A8 (Hello, KVM-A8 only supports Raspberry Pi 4B and does not support orange pi 4 compute module.)
  • 15:41, 14 September 2023 46.232.121.123 talk posted a new comment on XScript (pi@raspberrypi:~/xscript $ sudo systemctl status x-c1-fan.service ● x-c1-fan.service - Daemon to monitor and control fan speed Loaded: loaded (/lib/systemd/system/x-c1-fan.service; enabled; vendor preset: enabled) Active: active (running) since Thu 2023-09-14 07:29:03 BST; 58min ago Main PID: 461 (bash) Tasks: 2 (limit: 1599) CPU: 18.604s CGroup: /system.slice/x-c1-fan.service ├─ 461 bash /usr/local/bin/x-c1-fan.sh └─41092 sleep 5 Se...)
  • 15:38, 14 September 2023 46.232.121.123 talk posted a new comment on XScript (Hi NASPi Gemini 3.5 with Raspberry Pi 64bit Lite, fan not working : ()
  • 14:34, 14 September 2023 91.196.69.102 talk posted a new comment on PiKVM-A8 (Anyone know if this device will work with an orange pi 4 compute module? It is far more cost effective.)
  • 10:40, 14 September 2023 Walker talk contribs posted a new comment on P373 (Hello, there are two solutions for cooling Option 1: Use a blue thermal pad， Option 2: Do not use the blue thermal pad. You can use copper pad and silicone grease to dissipate heat You can refer to the picture below： 700px|none|Two solutions for cooling)
  • 10:39, 14 September 2023 Walker talk contribs posted a new comment on P232 (Hello, there are two solutions for cooling Option 1: Use a blue thermal pad Option 2: Do not use the blue thermal pad. You can use copper pad and silicone grease to dissipate heat You can refer to the picture below 700px|none|Two solutions for cooling)
  • 10:36, 14 September 2023 Walker talk contribs deleted comment #3985 on P232
  • 10:35, 14 September 2023 Walker talk contribs posted a new comment on P232 (Hello, there are two solutions for cooling 1. Use a blue thermal pad 2. If you don’t want to use the blue thermal pad. Copper sheets and silicone grease can be used You can refer to the picture below 700px|none|Two solutions for cooling)
  • 07:55, 14 September 2023 99.8.154.37 talk posted a new comment on P373 (In what situation should the copper pad be used instead of the large blue thermal pad?)
  • 07:52, 14 September 2023 99.8.154.37 talk posted a new comment on P232 (Question: Pardon me for being a bit dense, but, in what situation should the copper pad be used instead of the large blue thermal pad? I assume they aren't intended to be used together.)
  • 17:31, 12 September 2023 Walker talk contribs posted a new comment on X735-script (Hello, X735 can implement shutdown command. For details, you can refer here: [https://wiki.geekworm.com/X735-script#Prepair_software_shutdown_script''' '''software shutdown script ])
  • 17:27, 12 September 2023 Walker talk contribs deleted comment #3981 on X735-script
  • 17:22, 12 September 2023 Walker talk contribs posted a new comment on X735-script (Hello, X735 can use the shutdown command. For details, you can refer to here: ===Prepair software shutdown script=== sudo cp -f ./x735-softsd.sh /usr/local/bin/ <pre> Create a alias <code>x735off</code> command to execute the software shutdown <pre> echo "alias x735off='sudo /usr/local/bin/x735-softsd.sh'" >> ~/.bashrc source ~/.bashrc </pre> Then you can run <code>x735off</code> to execute software shutdown.)
  • 17:22, 12 September 2023 Walker talk contribs deleted comment #3980 on X735-script
  • 17:21, 12 September 2023 Walker talk contribs posted a new comment on X735-script (Hello, X735 can use the shutdown command. For details, you can refer to here: ===Prepair software shutdown script=== sudo cp -f ./x735-softsd.sh /usr/local/bin/ Create a alias <code>x735off</code> command to execute the software shutdown <pre> echo "alias x735off='sudo /usr/local/bin/x735-softsd.sh'" >> ~/.bashrc source ~/.bashrc </pre> Then you can run <code>x735off</code> to execute software shutdown.)
  • 17:19, 12 September 2023 Walker talk contribs deleted comment #3979 on X735-script
  • 17:18, 12 September 2023 Walker talk contribs posted a new comment on X735-script (Hello, X735 can use the shutdown command. For details, you can refer to here: ===Prepair software shutdown script=== </pre> sudo cp -f ./x735-softsd.sh /usr/local/bin/ Create a alias <code>x735off</code> command to execute the software shutdown <pre> echo "alias x735off='sudo /usr/local/bin/x735-softsd.sh'" >> ~/.bashrc source ~/.bashrc </pre> Then you can run <code>x735off</code> to execute software shutdown.)
  • 17:15, 12 September 2023 Walker talk contribs deleted comment #3978 on X735-script
  • 17:14, 12 September 2023 Walker talk contribs posted a new comment on X735-script (Hello, X735 can use the shutdown command. For details, you can refer to here: ===Prepair software shutdown script=== sudo cp -f ./x735-softsd.sh /usr/local/bin/ Create a alias <code>x735off</code> command to execute the software shutdown <pre> echo "alias x735off='sudo /usr/local/bin/x735-softsd.sh'" >> ~/.bashrc source ~/.bashrc </pre> Then you can run <code>x735off</code> to execute software shutdown.)
  • 17:14, 12 September 2023 Walker talk contribs deleted comment #3977 on X735-script
  • 17:14, 12 September 2023 Walker talk contribs posted a new comment on X735-script (你好,X735是可以实现使用关机命令的，具体的您可以参考这里： ===Prepair software shutdown script=== sudo cp -f ./x735-softsd.sh /usr/local/bin/ Create a alias <code>x735off</code> command to execute the software shutdown <pre> echo "alias x735off='sudo /usr/local/bin/x735-softsd.sh'" >> ~/.bashrc source ~/.bashrc </pre> Then you can run <code>x735off</code> to execute software shutdown.)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"