Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 11:48, 26 July 2022 Lisa talk contribs posted a new comment on X735 (Hello， X735 does not affect any USB ports.)
  • 21:09, 25 July 2022 84.220.88.57 talk posted a new comment on X735 (Hi, on a Raspberry Pi 4 only the USB port that receives power is capable of acting as a USB Device. The other USB ports are capable only of acting as USB Hosts. To power the Raspberry and use USB type C at the same time, you have to buy a splitter. Using the x735 module it is possible to be able to use the raspberry type C as a device while the power supply goes into the type C of the x735? Thank you in advance.)
  • 19:12, 25 July 2022 113.88.163.161 talk posted a new comment on X825-C8 (吉安666)
  • 17:03, 25 July 2022 Lisa talk contribs deleted comment #2691 on PiKVM
  • 17:02, 25 July 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， We do not compare with IPMI. In addition, What is the price of IPMI? Most people don't just consider the solution and ignore the price. Of course, if you have enough budget, you can ignore its price.)
  • 16:55, 25 July 2022 Harry talk contribs posted a new comment on PiKVM (Hi, pikvm.org to get more function details. Thanks)
  • 03:29, 24 July 2022 81.221.231.190 talk posted a new comment on X708-Software (unfortunately your node-red flow seem to have a syntax-error... Would you please provide it once more? i am very curious, how you did the node-red implementation. Thanks!)
  • 15:48, 23 July 2022 104.33.135.51 talk posted a new comment on PiKVM (Obviously this is a DIY / opensource version and the latter are enterprise solutions, but how does this compare to IPMI (or for Dell, iDRAC, and HP, ILo or Lights-out)?)
  • 16:30, 21 July 2022 188.235.21.221 talk posted a new comment on X750 Sofrware (You are using python version 3, parentheses should be used for it. Add them to the code or use python version 2)
  • 18:10, 19 July 2022 Lisa talk contribs posted a new comment on X735 (Yes, the higher the voltage, the lower the required current value. DC port ：it's positive center pin.)
  • 11:29, 19 July 2022 24.190.216.86 talk posted a new comment on X735 (Also, is that positive center pin?)
  • 11:16, 19 July 2022 24.190.216.86 talk posted a new comment on X735 (When powering via the 6-30v dc input, how much current should the power supply be rated for? Does that vary based on the input voltage?)
  • 17:52, 18 July 2022 Lisa talk contribs posted a new comment on PiKVM (Hi， It is a 2pin fan and does not support speed adjustment.)
  • 17:52, 18 July 2022 Lisa talk contribs deleted comment #2682 on PiKVM
  • 17:51, 18 July 2022 Lisa talk contribs posted a new comment on PiKVM (It is a normal 2pin fan and does not support speed adjustment)
  • 13:30, 18 July 2022 175.143.179.198 talk posted a new comment on PiKVM (Is the X630-A3 fan a 3-pin PWM fan that supports changing fan speed?)
  • 11:08, 18 July 2022 Lisa talk contribs posted a new comment on X-C1 Software (Could you you provide more details? For example, the installed script, is there any error message？)
  • 10:46, 18 July 2022 Lisa talk contribs posted a new comment on PiKVM (Hardware Real Time Clock (RTC) with CR1220 coin battery socket)
  • 06:10, 17 July 2022 95.90.206.152 talk posted a new comment on X-C1 Software (Hello, Installed the script on a Raspberry Pi 4 with newest version of raspbian on it. xoff is not working. After the 4 seconds, nothing happens. Fan speed is controlled so the script somehow works, but xoff not..)
  • 22:13, 16 July 2022 83.128.236.199 talk posted a new comment on PiKVM (What is RTC? Why do you need it?)
  • 11:27, 16 July 2022 Lisa talk contribs posted a new comment on M200 (Hi， Is there any error message? Could you please tell us more specific information send some pictures or videos【support@geekworm.com】? And tell us your order number. thanks)
  • 11:19, 16 July 2022 Lisa talk contribs posted a new comment on NASPi Gemini (There are two HDD indicator lights on the x882 board, you can observe the working status of the hard disk.)
  • 19:20, 15 July 2022 124.155.126.27 talk posted a new comment on M200 (When I install Ubuntu and try to use it, the device connected to the USB port is not recognized. The power itself seems to be coming through.)
  • 18:35, 15 July 2022 1.34.148.37 talk posted a new comment on NASPi Gemini (So what I need to know how do I know if one of the hard drives is broken? I just know which hard drive to replace)
  • 16:14, 15 July 2022 Lisa talk contribs posted a new comment on NASPi Gemini (Hello， Raid 1 performance: both hard drives have the same data； One hard disk is the direct visible hard disk capacity, and the other hard disk is equivalent to the mirror hard disk. The data is written at the same time. When the visible hard disk is damaged, the mirror hard disk will automatically restore the complete data to the hard disk. About software operation, you can get more information on google. Best regards)
  • 13:27, 15 July 2022 1.34.148.37 talk posted a new comment on NASPi Gemini (I have a NASPi gemini, and I build Raid 1 node, How can I get the information about one of HDDs is broken.)
  • 19:26, 12 July 2022 185.5.46.73 talk posted a new comment on X708-Software (Sorry, something went wrong while copying. Here is the node-red flow again: [{"id":"b6e375dca488451c","type":"rpi-gpio in","z":"4f0f7e9b873ed151","name":"GPIO6 AC-Power","pin":"6","intype":"tri","debounce":"25","read":false,"bcm":true,"x":230,"y":1290,"wires":"2e6d1c8dd9466d21"},{"id":"9153e12fa19c8a01","type":"comment","z":"4f0f7e9b873ed151","name":"Raspi4 GPIO6 Power-Status","info":"","x":190,"y":1240,"wires":[]},{"id":"2e6d1c8dd9466d21","type":"change","z":"4f0f7e9b873ed151","name":""...)
  • 19:07, 12 July 2022 185.5.46.73 talk posted a new comment on X708-Software (For Geeworm UPS HAT: Here is my flow in node-red for reading the battery voltage and capacity as well as fan speed and power status. Required nodes: node-red-contrib-buffer-parser node-red-contrib-i2c node-red-node-pi-gpio [{"id":"b6e375dca488451c","type":"rpi-gpio in","z":"4f0f7e9b873ed151","name":"GPIO6 AC-Power","pin":"6","intype":"tri","debounce":"25","read":false,"bcm":true,"x":230,"y":1290,"wires":"2e6d1c8dd9466d21"},{"id":"9153e12fa19c8a01","type":"comment","z":"4f0f7e9b873ed151",...)
  • 18:50, 12 July 2022 Lisa talk contribs posted a new comment on X820 (Hi，It may be caused by USB2.0 interference. But this is rarely encountered, and in most cases it can be used normally. You can try to use an USB3.0 cable instead of the bridge to test.)
  • 17:48, 11 July 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hi， Is there any error message? Or you can try to reinstall the system to test it.)
  • 15:44, 11 July 2022 14.199.37.130 talk posted a new comment on X820 (Hi, the AP function of PI3B disconnected after plug-in the USB bridge with X820 V.3. Are there any confflict between USB2 and 3? Thanks)
  • 14:54, 11 July 2022 Lisa talk contribs posted a new comment on X708 (Hi, We can provide PCB size pictures, but can't provide schematic diagrams)
  • 12:28, 11 July 2022 Lisa talk contribs posted a new comment on X400 V3.0 (Hello， Could you please send a test video to [support@geekworm.com];and let us known your order No. ; Thanks)
  • 12:27, 11 July 2022 Lisa talk contribs deleted comment #2663 on X400 V3.0
  • 12:27, 11 July 2022 Lisa talk contribs posted a new comment on X400 V3.0 (Hello， Could you please send a test video to [support@geekworm.com];and let us known your order No. ; Thanks)
  • 12:28, 10 July 2022 71.25.178.65 talk posted a new comment on X708 (Can I get the x708 v2.0 schematic.)
  • 18:49, 9 July 2022 77.164.231.31 talk posted a new comment on X400 V3.0 (Q7 solution is not working RI 3B+ X400)
  • 04:17, 9 July 2022 87.122.80.28 talk posted a new comment on X-C1 Software (Hello, after creating a new image I was able to install the required programs. The pin for FanFS is bridged. The script Pigpio is present and also the script x-C1. No matter what I change in the fan.pi file, the fan does not turn off. My OS ist Citadel-Node (similar Umbrel), Hardware P4)
  • 00:52, 9 July 2022 87.122.80.28 talk posted a new comment on X-C1 Software (Hello, after creating a new image I was able to install the required programs. The pin for FanFS is bridged. The script Pigpio is present and also the script x-C1. No matter what I change in the fan.pi file, the fan does not turn off.)
  • 18:39, 8 July 2022 178.73.193.14 talk posted a new comment on X708-Hardware (The fan in the case is probably connected to 5 V without regulation. I connected it to the 3.3V pin of the Raspi. Now it's quiet!)
  • 15:20, 8 July 2022 80.187.117.104 talk posted a new comment on X-C1 Software (The data for the fan is not installed with the script. The former file that was installed was used for the shutdown.) Tags: Mobile web edit, Mobile edit
  • 09:20, 8 July 2022 Lisa talk contribs posted a new comment on X-C1 Software (Hi， What version is your X-C1? X-C1 v2.0 added Fan FS jumper, please check if the Fan FS jumper cap is shorted.)
  • 04:34, 8 July 2022 87.122.83.114 talk posted a new comment on X-C1 Software (Hello, I wanted to use this case with Citadel Node. Apart from the x-c1-softsd file, no other file is created when the script for My-Node is executed. The fan runs but is not regulated. ;-/)
  • 16:32, 7 July 2022 Lisa talk contribs posted a new comment on X735 Software (Jumper No. function please refer X735 Hardware)
  • 23:54, 6 July 2022 148.71.178.50 talk posted a new comment on X735 Software (It worked! I didn't shorted the FAN FS. I couldn't find any documentation for what to short and not to short in the wiki. Thank you!)
  • 15:56, 6 July 2022 Lisa talk contribs posted a new comment on C779 (Hello， This chip TC358743 supports up to 8bit 444)
  • 11:47, 6 July 2022 Lisa talk contribs posted a new comment on X735 Software (Hi， ①Please check if the Fan FS jumper cap is shorted. ②The installation script restarts running sudo python3 read_fan_speed.py, is it possible to read the fan speed?)
  • 18:24, 5 July 2022 148.71.178.50 talk posted a new comment on X735 Software (I forgot to mention, I using x735 v3)
  • 18:23, 5 July 2022 148.71.178.50 talk posted a new comment on X735 Software (Hi After installing script in Ubuntu server (20.04) fan still works at full speed (more than 5000RPM). Already try several installs and server reinstalls and still always full spin. pwm_fan_control.py runs of startup but doesnt seems to control the spin Do you think im missing something? Thanks)
  • 16:48, 5 July 2022 212.18.205.146 talk posted a new comment on C779 (We tried to capture from the Blackmagic Pocket Cinema Camera 6K, which supposedly has 1080p output in 10-bit. It only gave us a magenta tinted image. We tested the module with another 8bit input, which looks fine. Any idea how to get a correct image from the Blackmagic cam?)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"