Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 18:27, 19 October 2022 185.13.50.181 talk performed unknown action "comments/add" on NASPi (I've bought a Noctua 40x10mm non-PWM fan and it looks like I need to make some cable modifications as the connector block on the Noctua won't fit the onboard connector on my X-C1 v2.0. I have a 3 to 2 pin adapter cable that came with my fan. Can the onboard 5V connector be used to power the new fan instead of having to cut cables?)
• 16:37, 17 October 2022 Lisa talk contribs performed unknown action "comments/add" on X880 (Hi， Yes， you can use the CLEAR RAID mode (PM, factory default setup) and not format the hdds.Plese back up your data to avoid unexpected situations.Thanks.)
• 15:18, 17 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware (Hi， amazon.de/gp/product/B07KCCLGXJ----Operating voltage 12 Volts； X708 UPS output is 5V)
• 00:19, 16 October 2022 213.147.102.162 talk performed unknown action "comments/add" on X880 (Hi, if I want to have a clear RAID is it necessary to make any RAID changes once I set up the X880 and install HDDs? I do not want to format the drives or lose any data! IF clear RAID is default I guess all should work fine without formating the HDDs?? Thnx)
• 16:52, 14 October 2022 86.103.20.66 talk performed unknown action "comments/add" on X708-Hardware (Thank you for your quick reply. I think the pinout in this documentation is wrong. It says: 1 Power on/off control connecting to switch 2 Ground 3 LED+ for battery low indicator 4 LED+ for power on, rebooting and shutdown But shorting pin 1 and pin 2 has no effect. Instead, shorting pin 2 and pin 4, I get the expected behavior like Power on and force shutdown (holding >8 seconds). I have a X708 V2.0 if that makes a difference. I have a normally open four pin momentary switch with build...)
• 11:28, 14 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708-Software (Hi Please check whether the positive and negative poles of the battery are correctly installed, if you use 18650 batteries. Replace other batteries to test.)
• 11:16, 14 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware (Hi， Please refer toX708-Software)
• 11:13, 14 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware (Hello， The [external power switch connector] on the board only support a momentary switch.)
• 08:18, 13 October 2022 86.245.255.107 talk performed unknown action "comments/add" on X708-Software (Hi, how is evaluated the battery level ? I put 2 fully charged battery on the x708v2 but it considered they where 0%, so they have been charge for hours, and maybe overcharged ! Now battery make the x708 to bug. The battery failed led is blinking while power supply is connected. How to calibrate the battery level mesure ? Thanks)
• 07:38, 12 October 2022 86.103.219.92 talk performed unknown action "comments/add" on X708-Hardware (Is there any way to "turn off" the X708 when the Pi is shut down? Currently I have to press the button for a long time (7 sec) after shutdown to do this.)
• 04:00, 12 October 2022 86.103.219.92 talk performed unknown action "comments/add" on X708-Hardware (Hi! How do I connect a NO push button with LED to the 4 pin interface? Thank you)
• 18:03, 11 October 2022 Harry talk contribs created page File:X306V1.1.dxf
• 18:03, 11 October 2022 Harry talk contribs uploaded File:X306V1.1.dxf
• 09:47, 11 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708 (Hi， There is no a case for Pi4 + X825 V2.0 + X708 + 18650 bateery holder yet. But we will be pruducing a matching Case for it in the near future.)
• 15:40, 10 October 2022 151.74.5.94 talk performed unknown action "comments/add" on X708 (Hi, please what case fits for x825 v.2.0 + pi4 + x708 v.2.0 + 18650 battery holder?)
• 12:37, 6 October 2022 Lisa talk contribs performed unknown action "comments/add" on NASPi Gemini (Hi， Yes，you can use it.)
• 12:34, 6 October 2022 Lisa talk contribs performed unknown action "comments/add" on X735 Software (Hello， The installation scripts of V3.0 and V2.5 are the same. Refer to the sample script above.Thanks~)
• 12:29, 6 October 2022 Lisa talk contribs performed unknown action "comments/add" on T208-hardware (Hello， Thanks for your question.please refer topT208#FAQ.)
• 12:14, 6 October 2022 Lisa talk contribs performed unknown action "comments/add" on X708-Hardware (Hello， 1. The fan of X728-C1 case is only GND 5V ，does not controlled by GPIO. 2. You can unplug it's cable if you want to stop it.)
• 22:15, 5 October 2022 213.94.32.103 talk performed unknown action "comments/add" on X735 Software (Hi, I installed the fan v3.0 on my raspberry pi4, but the button work only for turning on the pi and for a forced shutdown. How can I enable the reset and safe shutdown? Do you have an installation script for the v3.0?)
• 04:52, 5 October 2022 86.245.255.107 talk performed unknown action "comments/add" on X708 (Lithium-ion battery are wearing when kept fully charge all the time. To preserve the battery longevity is it possible to limit the maximum capacity/voltage charge ? For Example I would like to limit the charge at 85% maximum. Thanks !)
• 04:08, 5 October 2022 94.234.116.82 talk performed unknown action "comments/add" on NASPi Gemini (Is the 5v out plug on the board functional?) Tags: Mobile edit Mobile web edit
• 23:00, 4 October 2022 2.50.121.7 talk performed unknown action "comments/add" on X708-Hardware (Now that you mentioned it, it makes sense. Since when this happens, it is accompanied by a notable increase in the fan speed. Thank you "Anonymous user #13" whoever you are.)
• 11:22, 4 October 2022 189.181.238.63 talk performed unknown action "comments/add" on X708-Hardware (HS, is for High Speed. It's used by the fan.py script, when above the threshold it start spinning faster and lowered speed when temp is below threshold. Notice that x708 fan is always running at low speed.)
• 10:43, 4 October 2022 133.232.65.249 talk performed unknown action "comments/add" on X735 Software (Hello, I bought a cooling fan X735 ver. 3.0 for my raspberry pi 4B and tried to install it. Reading the manual, it seems that X735 has the following GPIOs dedicated. GPIO 5,12,13,16,20 However, my plan is to use the following GPIOs for another purpose. Unfortunately, for various reasons, this cannot be changed. GPIO 16,20,21 Therefore, I would like to change the duplicated GPIOs used for X735 as follows. from 16 to 19 from 20 to 26 How should I rewrite the programs and execute them?...)
• 22:54, 3 October 2022 46.182.212.220 talk performed unknown action "comments/add" on T208-hardware (Hello, What kind of battery can I use with the T208 ? (Voltage range, max capacity) I'm asking because most 18650 batteries are 3,7V which I'm not sure is up to the specs. If you have any reference to give as an example ; I would be glad.)
• 21:16, 3 October 2022 102.42.145.124 talk performed unknown action "comments/add" on LHT00SU1 Virtual Oscilloscope SKU:412961 (lht00su1 virtual driver)
• 20:53, 3 October 2022 2.50.121.7 talk performed unknown action "comments/add" on X708-Hardware (What is the indication of the LED labled (HS) beside the LED labled (FAN) on the x708 v2? It turned red the first time when I connected the ground of the Raspberry Pi with the ground of an external power supply I use to control devices that need more power. Now it is red even when the ground of the Raspberry pi is not connected to anything. The Raspberry pi powers nothing through its 5V)
• 17:40, 3 October 2022 109.136.113.78 talk performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (Does someone knows the board I need to select in Arduino IDE to upload my program into this? (from the ESP32 board list))
• 02:45, 3 October 2022 189.181.238.63 talk performed unknown action "comments/add" on X708-Hardware (Which GPIO pin can be used to control Case Fan x728-C1? Is it possible to stop the x708 board fan? (not LOW but STOP))
• 10:07, 30 September 2022 Lisa talk contribs performed unknown action "comments/add" on X-C1 Software (Hi， Sorry, it doesn't support Home Assitant yet.)
• 04:53, 30 September 2022 109.231.0.65 talk performed unknown action "comments/add" on X-C1 Software (Hi, is it possible on Home Assistant?)
• 02:36, 30 September 2022 176.133.137.224 talk performed unknown action "comments/add" on X-C1 Software (Hello)
• 12:13, 29 September 2022 Lisa talk contribs performed unknown action "comments/add" on M200 (Hi， 1/Could you please tell us what power supply do you use? If connect external SSD, we suspect maybe the power supply is not enough to power the SSD. 2/Do you mean that you can boot from USB or SSD when use a OTG cable on the NC PORT?)
• 10:50, 29 September 2022 Lisa talk contribs performed unknown action "comments/add" on NASPi (Hello, You can use GPIO pins other than X-C1 GPIO Use: 4,17,27,18. But we haven't tested if the Naspi case supports the ESP8266.)
• 02:53, 29 September 2022 69.156.39.124 talk performed unknown action "comments/add" on NASPi (Hi I want to use ESP8266 with this setup but require pins 1,3,5,8 and 10 on the GPIO. Is this possible?)
• 00:30, 29 September 2022 82.64.55.9 talk performed unknown action "comments/add" on M200 (Why is it not possible to boot on usb port with à bootable usb key or ssd ? Curiously with an otg câble on the n.c. micro usb entry it works...) Tags: Mobile edit Mobile web edit
• 19:18, 28 September 2022 207.253.40.113 talk performed unknown action "comments/add" on UPS3 (Hello I have one of your UPS v3 connecter to my Pi. I have activated the Auto UPS feature (on). However, when the Pi is powered off using the poweroff command, the Pi does not restart when power is put back on. What could be the cause?)
• 10:51, 28 September 2022 Lisa talk contribs performed unknown action "comments/add" on X728-Software (Anonymous user #34 ：Hello， Please use your own username after '/home/pi/'. That is, the username created by the initial user of the Raspberry Pi OS system)
• 07:44, 28 September 2022 73.240.70.136 talk performed unknown action "comments/add" on X728-Software (I to do not understand how to get the x728 file to work and how to rename to my rpi, Please help The x728v2- say no such file or directory)
• 19:36, 27 September 2022 Harry talk contribs created page File:T201-IMG-4233-Interface-Schematic.jpg
• 19:36, 27 September 2022 Harry talk contribs uploaded File:T201-IMG-4233-Interface-Schematic.jpg
• 19:05, 27 September 2022 Harry talk contribs uploaded a new version of File:T201-IMG-4814.jpg
• 19:04, 27 September 2022 Harry talk contribs created page File:T201-IMG-4814.jpg
• 19:04, 27 September 2022 Harry talk contribs uploaded File:T201-IMG-4814.jpg
• 09:53, 27 September 2022 Lisa talk contribs performed unknown action "comments/add" on X728-hardware (Hi，You don't have to use the batteries we recommend, but please make sure to use genuine, high-quality batteries. And note the X728's requirements for battery size--[18650 battery dimension] . Thank you.)
• 17:50, 26 September 2022 Abby talk contribs created page File:LT2611UXC-Product-Brief.pdf
• 17:50, 26 September 2022 Abby talk contribs uploaded File:LT2611UXC-Product-Brief.pdf
• 12:42, 26 September 2022 186.96.100.60 talk performed unknown action "comments/add" on X728-hardware (Hi, I'm unable to find the recommended battery Panasonic NCR18650B, as a replacement, the seller recommends the Panasonic NCR18650GA, 3450mAh battery. Is it ok to use that model? Thank you very much!)
• 11:29, 26 September 2022 Lisa talk contribs performed unknown action "comments/add" on NASPi Gemini (Hello， X882 is mainly used for data access, it is recommended that you try to boot from SD card.)