-
H505
Overview
Geekworm has brought several heatsink products that are as good as the official Raspberry Pi active cooler, and they are all designed for the Raspberry Pi 5.
After testing, the heat dissipation performance of the Geekworm active radiator series is no less than or better than the official active cooler, and the heat dissipation performance of some models will exceed the official cooler, such as the H505 cooler, due to the use of thermal pads with higher thermal conductivity , while adding more thermal contact area in contact with the Raspberry Pi 5 motherboard, and the aluminum alloy heatsink is also thicker than the official cooler, and also has more heat dissipation fins. There is no doubt that its heat dissipation performance is more than Official cooler.
Like other H503, H501 radiator also has good heat dissipation performance and is suitable for a wide range of applications in your products.
The H505 does not support X1003.
Geekworm Cooler Series:
| Picture | Model | Compatible With | Material | Thickness(mm) | Support Fan | |
|---|---|---|---|---|---|---|
 |
C519 | Raspberry Pi Computer Module 5 (CM5) | Aluminum Alloy | 15mm | √ support fan installation | |
 |
Pi 5 official Active Cooler | Raspberry Pi 5 | Aluminum Alloy | 10mm | √ with 4-pin 3007 blower fan | |
|
H505 | Raspberry Pi 5 | Aluminum Alloy | Net Weight: 39g | √ with 4-pin 3007 blower fan | |
 |
H509 | Raspberry Pi 5 | Aluminum Alloy | 15mm | × don't support fan installation | |
 |
H510 | Raspberry Pi 5 | Brass | 10mm / Net Weight: 55g | √ with 4-pin 3007 blower fan | |
 |
Argon THRML 30-AC | Raspberry Pi 5 | Aluminum Alloy | 9.6mm | √ with 4-pin 3007 blower fan | |
 |
H501 | Raspberry Pi 5 | Aluminum Alloy | 9.5mm | √ with 4-pin 3007 blower fan | |
 |
H502 | Raspberry Pi 5 | Brass | 4mm | × support 30x30 fan installation | |
 |
P165-B | Raspberry Pi 4 | Aluminum Alloy | 11mm | × support 30x30 fan installation | |
 |
P165-A | Raspberry Pi 4 | Aluminum Alloy |
7mm/8mm (Version updated; 2 versions available, 8mm (new), compatibility unaffected) |
× support 25x25 fan installation | |
 |
H402 | Raspberry Pi 4 | Brass | 4mm | × don't support fan installation | |
 |
C235 | Raspberry Pi Computer Module 4 (CM4) | Aluminum Alloy | 12mm | × support 30x30 fan installation | |
 |
C296 | Raspberry Pi Zero 2 W | Aluminum Alloy | 10mm | × don't support fan installation |
Features
- Compatible with Raspberry Pi 5: Geekworm active cooler Aluminum Heatsink is only designed for Raspberry Pi 5 8GB/4GB and all variants
- Support PWM Speed Control: Different from ordinary fans, this cooling fan supports PWM speed regulation, which is perfectly compatible with Raspberry Pi OS.
- Good Heat Dissipation Effect: With 3007 ultra-quiet cooling fan and good quality thermal pads, it can lower the temperature of Raspberry Pi Board quickly.
- Lightweight and Easy to Install: Easy to install, just push it in directly using clamps.
Packing List
- 1x H505 Active Cooler
- 1x 5pcs Thermal Pads
User Manual
FAQ
Q: What should I do if the cooling fan makes a loud, rattling or scratching noise?
A: If you experience abnormal noise from the fan, it may be caused by the fan blades slightly rubbing against the metal cover due to over-tightened screws.
Our fans are assembled manually, which can occasionally lead to variations in how tightly the screws are fastened. If a screw is tightened too much, it can slightly warp the fan frame and cause the blades to hit the housing.
To resolve this issue, please follow these simple steps:
1. Loosen the screws slightly: Locate the 3 mounting screws on the fan. Using a suitable screwdriver, loosen each screw by about a half-turn to a full turn. Do not remove them completely—just relieve the tension.
2. Test the fan: Power on your device to see if the noise disappears.
3. Adjust if necessary: If the noise persists, try adjusting the tightness of each of the 3 screws individually until the fan runs smoothly and quietly.
