X1011: Difference between revisions
Replace <comments/> with <comment-streams /> |
|||
| (22 intermediate revisions by 3 users not shown) | |||
| Line 3: | Line 3: | ||
[[File:X1011-V1.1-Interface.jpg|thumb|right|X1011 V1.1]] | [[File:X1011-V1.1-Interface.jpg|thumb|right|X1011 V1.1]] | ||
[[File:004-X1011-V1.1-IMG-8108-SSD-Installation.jpg|thumb|right|X1011 V1.1]] | [[File:004-X1011-V1.1-IMG-8108-SSD-Installation.jpg|thumb|right|X1011 V1.1]] | ||
[[File:X1011-V1.1-IMG-8516-How | [[File:X1011-V1.1-IMG-8516-How to power.jpg|thumb|right|How to power]] | ||
[[File:X1011-V1.1-P4-W2000.jpg|thumb|right|X1011 V1.1]] | [[File:X1011-V1.1-P4-W2000.jpg|thumb|right|X1011 V1.1]] | ||
[[File:X1011-V1.1-P5.jpg|thumb|right|X1011 V1.1]] | [[File:X1011-V1.1-P5.jpg|thumb|right|X1011 V1.1]] | ||
| Line 45: | Line 45: | ||
---- | ---- | ||
{{PCIe to NVME Sets}} | {{PCIe to NVME Sets}} | ||
{{NVMe SSD Incompatibility List}} | |||
==Features== | ==Features== | ||
| Line 145: | Line 146: | ||
==Testimonial== | ==Testimonial== | ||
{{Testimonial | {{Testimonial | ||
|name= | |name=Anon. | ||
|date=April 2026 | |date=April 2026 | ||
|content= Subject: X1011 - Help on selecting a suitable power supply (test based on Geekworm 5V 10A Power Supply [[PSU50]]) | |content= Subject: X1011 - Help on selecting a suitable power supply ('''test based on Raspberry Pi 5 + X1011 + 4 NVMe SSD + Geekworm 5V 10A Power Supply [[PSU50]]''') | ||
'''Email1:''' | |||
I purchased the Geekworm X1011 5V PCIe to Four M.2 NVMe SSD Board for Raspberry Pi 5. I installed 4 WD 4Tb NVME drives. Things ran for a bit.. (OMV7-Bookworm).. As the Raid5 set was cleaning.. OMV eventually ended by dumping all four drives.. I wonder if the 5 amp power supply is not enough.. (I am using the Geekworm GaN PD 27W 5.1V 5A Power Supply) | |||
I found a 5V 8A Power Adapter, 100-240V AC to DC Power Supply transformer on amazon.ca.. Unfortunately they do not document the configuration of the DC Jack (ASIN-809MQNBX8H, Manufacturer reference - Diocheya6gr98w1h489 Country - China). Product detail describes the connector type as default... | |||
Would you have a recommendation for a power supply with greater amps? Or.. would the 8A one described above be ok? | |||
I await your recommendation | |||
'''Email2:'''I received the 10a power supply yesterday and pressed it into service immediately. | |||
The best test of it was to use OMV8 (Open Media Vault 8 – under IOS – Trixie) to create a RAID5 group of all 4 nvme 4tb drives.. | |||
After a short time, one of the drives failed… (I suspect that it was hurt with the weak power from the original limited 5a power supply).. I installed a preplacement nvme drive and restarted the process.. This morning the RAID 5 group is up and working well.. | |||
This is a much better result compared with the 5a power supply.. I will update you in a week or so to let you know if anything comes up.. At this point, I would say that this 10a power supply is better for a fully populated X1011 with larger nvme drives.. | |||
'''Email3:''' The testing continues… The Crucial nvme drives did not work out as there was not enough clearance in the case. In the future it may be great to redesign the Geekworm X1011-C1 PCIe Metal Case for Raspberry Pi 5 to add at least 1cm of depth to permit better air flow for the nvme’s and clearance for the heatsinks… | '''Email3:''' The testing continues… The Crucial nvme drives did not work out as there was not enough clearance in the case. In the future it may be great to redesign the Geekworm X1011-C1 PCIe Metal Case for Raspberry Pi 5 to add at least 1cm of depth to permit better air flow for the nvme’s and clearance for the heatsinks… | ||
| Line 176: | Line 193: | ||
''' | '''Email4:''' The WD Blue drives came in on Friday and my testing started immediately.. The Open Media Vault is working well on it and I did a number of long transfers which went well.. | ||
Observations: | |||
The X1011 needs a good fan (Which I have).. This keeps the NVME’s in the range of 29-35C .. (. In the future it may be great to redesign the Geekworm X1011-C1 PCIe Metal Case for Raspberry Pi 5 to add at least 1-2cm of depth to permit better air flow for the nvme’s and clearance for the heatsinks) | |||
The NVME which work well have no chips on the down side .. The NVME’s with problems were all ones with chips on both sides of the NVME.. The WD Blue SN5000 and the WD_BLACK SN8100 4TB work well… On the other hand, the WD_BLACK 4TB SN850X has chips on both sides of the NVME and it overheats.. and can get up to 70C in the same setup.. (end up with many errors and ultimately failures) | |||
The 10A power supply is great for the NVME’s (and system solutions) which draw more current… and for those who are using both USB 3 ports on the Raspberry 5 to drive a 2.5GB RJ45 network adapter and a large USB system drive. | |||
All in all, things are looking up! | |||
Thank you for your help in creating a working solution! | |||
'''Summary & Recommendations''' | |||
Power Supply Requirements: | |||
* 5V 5A (Standard): Insufficient for the X1011 when fully populated with 4 NVMe SSDs, especially during power-intensive operations like RAID5 rebuilding/cleaning. This may lead to drive disconnections or system instability. | |||
* 5V 10A (Recommended): The Geekworm PSU50 (5V 10A) is highly recommended for configurations using 4TB or high-performance drives to ensure stable voltage and prevent data loss. | |||
Thermal Considerations: | |||
* High-capacity NVMe drives (e.g., WD Black series) generate significant heat. It is critical to ensure adequate airflow. | |||
* Using an external cooling fan can maintain drive temperatures around 22°C - 29°C, significantly extending hardware lifespan. | |||
Hardware Compatibility: | |||
* Users should verify the physical clearance of NVMe heatsinks within the '''X1011-C1''' metal case. Some high-profile drives or heatsinks may require additional case depth for optimal fit and airflow. | |||
}} | }} | ||
| Line 216: | Line 244: | ||
<!--Add review function! --> | <!--Add review function! --> | ||
< | <comment-streams id="main" /> | ||
<!--Please choose the --> | <!--Please choose the --> | ||