Open main menu
Geekworm Wiki

Difference between revisions of "X1207"
 
(19 intermediate revisions by 3 users not shown)
Line 3: Line 3:
 
[[File:X1207-IMG-0073.jpg|thumb|right|X1207 V1.2]]
 
[[File:X1207-IMG-0073.jpg|thumb|right|X1207 V1.2]]
 
[[File:X1207-IMG-0101-pogo-pin-connection.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 
[[File:X1207-IMG-0101-pogo-pin-connection.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
−
[[File:X1207-IMG-0105.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
+
[[File:X1207-IMG-0105-Power.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 
[[File:X1207-IMG-0077.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 
[[File:X1207-IMG-0077.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 
[[File:X1207-IMG-0099.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
 
[[File:X1207-IMG-0099.jpg|thumb|right|X1207 V1.2 with Raspberry Pi 5]]
  
 
==Safety Instructions & Warnings==
 
==Safety Instructions & Warnings==
−
'''⚠''' <span class="tb_red">The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before installing your battery in the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.
+
{{UPS Safety Warning}}
−
 
 
−
'''⚠''' <span class="tb_red">It is essential to read and understand these safety instructions and warnings before charging your batteries.
 
−
 
 
−
'''⚠''' <span class="tb_red">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal  injury, and damage to property if charged or used improperly.
 
−
 
 
−
'''⚠''' <span class="tb_red">Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the  battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
 
−
 
 
−
'''⚠''' <span class="tb_red">Do not mix and use old batteries with new batteries, or batteries with different brand names.
 
−
 
 
−
'''⚠''' <span class="tb_red">Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when  they are two years old, whichever comes first.
 
−
 
 
−
'''⚠''' <span class="tb_red">When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material  or carpet unattended.
 
−
 
 
−
'''⚠''' <span class="tb_red">Keep the UPS shield away from children to ensure their safety.
 
  
 
==Overview==
 
==Overview==
Line 73: Line 59:
 
* [[X1002]] single NVMe shield for Pi5
 
* [[X1002]] single NVMe shield for Pi5
 
* [[X1005]] dual NVMe shield for Pi5
 
* [[X1005]] dual NVMe shield for Pi5
−
* [[X1006]] PCIe to SATA 2.5 HDD+M.2 SSD shield for Pi 5
 
−
* [[X1007]] PCIe to dual SATA 2.5 HDD/SSD shield for Pi 5
 
−
* [[X1100]] USB3 to SATA 2.5 HDD/SSD shield for Pi 5
 
−
* Other add-on boards are attached to the bottom of the Raspberry Pi
 
 
|-
 
|-
 
| '''Notes''' ||  
 
| '''Notes''' ||  
Line 124: Line 106:
  
 
==Matching Case==
 
==Matching Case==
−
No matching case yet.
+
The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5 X1207/'''[[X1208]]''' UPS Shield, offering robust protection in a sleek, black aesthetic.
 +
* Case dimension: 92.8 x 90.8 x 42.8 mm
 +
 
 +
<gallery>
 +
 
 +
X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories
 +
X1207-C1-IMG-0167.jpg|X1207-C1
 +
X1207-C1-IMG-0170.jpg|X1207-C1
 +
X1207-C1-IMG-0174.jpg|X1207-C1
 +
 
 +
</gallery>
  
 
==FAQ==
 
==FAQ==

Latest revision as of 11:49, 22 December 2025

X1207 V1.2 Interface Schematic
X1207 V1.2
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5
X1207 V1.2 with Raspberry Pi 5

Contents

Safety Instructions & Warnings

  • It is essential to read and understand these safety instructions and warnings before charging your batteries.
  • Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.
  • Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
  • Do not mix and use old batteries with new batteries, or batteries with different brand names.
  • Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.
  • When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.
  • Keep the UPS shield away from children to ensure their safety.
  • Ensure your fingers do not touch the solder pads when inserting the battery into the battery holder, as this could cause a short circuit. This is extremely important!!!
  • Make sure to insert the battery before turning on the UPS.
  • Make sure to insert the battery before connecting the external charger to charge it.
  • Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/
  • Battery Recommend for Geekworm UPS board, please refer to: File:NCR18650B.pdf

Overview

The X1207 is a PoE-powered UPS HAT designed for Raspberry Pi 5, delivering reliable 5.1V/5A backup power to maintain uninterrupted operation. It supports high-demand setups and complies with IEEE 802.3af/at PoE standards, drawing up to 25W from a compatible POE switch while providing both power and network connectivity over a single cable.

With intelligent power management, it monitors Pi status, cuts power after shutdown to conserve battery, and features ultra-low standby consumption. The board ensures seamless power switching during outages and supports auto power-on and AC loss detection.

Model Compatible with Position Lithium battery type Battery Holders Power Input Connector Power Output Connector Note Matching Case
X1200 Raspberry Pi 5 Bottom 3.7V 18650 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1200
 5Vdc Power Output XH2.54-2P x2 - X1200-C1
X1201 Raspberry Pi 5 Bottom 3.7V 18650 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1201
  • 5Vdc ≥3A via XH2.54-2P connector of X1201
 5Vdc Power Output XH2.54-2P x3 Ultra-thin X1201-C1
X1202 Raspberry Pi 5 Bottom 3.7V 18650 Battery 4-Cell
  • 5Vdc 5A via USB Type-C of X1202
  • 6-18Vdc ≥3A via DC 5521 power jack of X1202
  • 6-18Vdc ≥3A via XH2.54-2P connector of X1202
 5Vdc Power Output XH2.54-2P x2 - X1202-C1
X1203 Raspberry Pi 5 Bottom 3.7V Lithium Battery No battery holder
  • 5Vdc 5A via USB Type-C of X1203
  • 6-18Vdc ≥3A via DC 5521 power jack of X1203
  • 5Vdc ≥3A via XH2.54-2P connector of X1203
 5Vdc Power Output XH2.54-2P x2 - -
*X1205 Raspberry Pi 5 Bottom 3.7V 21700 Battery 2-Cell
  • 5Vdc 5A via USB Type-C of X1205
  • 9-18Vdc ≥3A via DC 5521 power jack of X1205
  • 9-18Vdc ≥3A via XH2.54-2P connector of X1205
 5Vdc Power Output XH2.54-2P x2 - X1205-C1
*X1206 Raspberry Pi 5 Bottom 3.7V 21700 Battery 4-Cell
  • 5Vdc 5A via USB Type-C of X1206
  • 5-6Vdc ≥3A via DC 5521 power jack of X1206
  • 5-6Vdc ≥3A via XH2.54-2P connector of X1206
 5Vdc Power Output XH2.54-2P x2 - X1206-C1
*X1207 Raspberry Pi 5 Top 3.7V 21700 Battery 1-Cell
  • 5Vdc 5A via USB Type-C of X1207
  • 35-57VDC powering over Ethernet
 - Support PoE-Powered

X1207-C1

*X1208 Raspberry Pi 5 Top 3.7V 21700 Battery 1-Cell
  • 5Vdc 5A via USB Type-C of X1208
 - Support M.2 NVMe SSD 2230/2242/2280

X1207-C1

*X1209 RPi 5B/4B/3B/3B+ Top 3.7V Lithium Battery No battery holder
  • 5Vdc 5A via USB Type-C of X1209
  • 6-18Vdc ≥3A via DC 5521 power jack of X1209
 5Vdc Power Output XH2.54-2P x2 - --

Features

For use with Raspberry Pi 5 Model B
UPS Output
  • Built for continuous, long-lasting operation -providing unwavering power for always-on Raspberry Pi systems
  • Supports a maximum current output of 5.1V 5000mA, suitable for most Raspberry Pi applications
  • Integrated Advanced Power MOSFET with an equivalent of 7mΩ RDS(ON) to minimize power loss
  • Power the Pi directly through the 40-pin header, eliminating the need for cables and soldering
Battery Charging
  • Supports battery charging with a capacity of 1500mA
  • Battery charging control can be managed via GPIO
  • Provides protection against battery overcurrent and overvoltage
  • Built-in protection against reverse connection of battery cells
  • Integrated Maxim's fuel-gauge systems for reading battery voltage and percentage over i2c
  • On-board LEDs indicate battery charging and discharging levels of 25%, 50%, 75%, and 100%
  • Features a single 21700 battery holder, supporting battery of up to 5000mAh
Power Input
  • Supports Power over Ethernet (PoE) input capability
  • Provides up to 5A output current, enabling 1.5A charging while powering the system
  • Standard Compliance: IEEE 802.3af & 802.3at (PoE+)
  • Fully isolated switched-mode power supply (SMPS) topology
  • Simplified single-cable installation and robust power delivery for Raspberry Pi
  • Compatible with Raspberry Pi USB-C Power Supply
Enhanced Power Management
  • Seamless power switching between backup power and power adapter
  • On-board push button performs the same actions as the Pi's power button
  • Automatically cuts off power when the Pi is shut down
  • On-board LED indicates power status and Pi detection
  • AC power loss and power adapter failure detection via GPIO
  • Auto power-on when power is applied or restored
  • Automatic safe shutdown when battery voltage is low (programmable)
  • Ultra-low standby power consumption to maximize battery life
  • Advanced system power-path management to minimize frequent charging and discharging of batteries
Compatible Accessories
  • X1002 single NVMe shield for Pi5
  • X1005 dual NVMe shield for Pi5
Notes
  • DON'T apply power to your Raspberry Pi 5 via the Type-C USB socket.
  • Compatible with unprotected 21700 battery only (Max. length: 70.3 mm).

Technical specification

Power input
  • 35-57VDC powering over Ethernet
  • 5Vdc 5A via USB-C
UPS output
  • 5.1V ±5% Max 5A
Battery charging current
  • 1.5A
Terminal Battery Voltage
  • 4.23V
Battery Recharge Threshold
  • 4.1V
Ports & Connectors
  • 4-pin POE female header x1
  • USB-C power in connector x1
  • 1-cell 21700 battery connector x1
  • 40-pin extended GPIO header x1
PCB Size
  • 86.5mm x 84.5mm

User Manual

Packing List

  • X1207 V1.2 UPS board x 1
  • Spacer M2.5 F/F 13.5mm x 4
  • Screw M2.5x5mm x 8
  • Pogo pin x 1 (For connecting to the Pi 5 PSW through hole)

 

Matching Case

The X1207-C1 is a premium metal case specially designed for the Raspberry Pi 5 X1207/X1208 UPS Shield, offering robust protection in a sleek, black aesthetic.

  • Case dimension: 92.8 x 90.8 x 42.8 mm

  • X1207-C1 Accessories

  • X1207-C1

  • X1207-C1

  • X1207-C1

FAQ

Q1: Question 1

A: Place the answer here.

Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Retrieved from "https://wiki.geekworm.com/index.php?title=X1207&oldid=24282"