X1208: Difference between revisions

(32 intermediate revisions by 8 users not shown)

Line 1:

[[File:X1208-IMG-9926-Interface.jpg|thumb|X1208 V1.0 Interface]]

[[File:X1208-IMG-0091-1.jpg|thumb|X1208 V1.0]]

[[File:X1208-IMG-0088.jpg|thumb|X1208 V1.0]]

[[File:X1208-IMG-0129.jpg|thumb|X1208 V1.0 with Raspberry Pi 5 ]]

[[File:X1208-IMG-0125-pogo-pin-connection.jpg|thumb|X1208 V1.0]]

[[File:X1208-IMG-0105-Power.jpg|thumb|X1208 V1.0 with Raspberry Pi 5 & SSD card]]

==SAFETY INSTRUCTIONS AND WARNINGS==

* <span style="color:red;">The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before connecting your battery to the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.

* <span style="color:red;">It is essential to read and understand these safety instructions and warnings before charging your batteries.

* <span style="color:red;">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.

* <span style="color:red;">Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".

* <span style="color:red;">Do not mix and use old batteries with new batteries, or batteries with different brand names.

* <span style="color:red;">Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.

* <span style="color:red;">When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.

* <span style="color:red;">Keep the UPS shield away from children to ensure their safety.

==Overview==

Line 62:

* High-efficiency converter delivers 3.5A to your SSD

~~'''Compatible Accessories'''~~

* [[X1100]] USB3 to SATA 2.5 HDD/SSD shield for Pi 5

* Other add-on boards that do not use the PCIe interface are attached to the bottom of the Raspberry Pi 5.

|-

| '''Spec''' ||

Line 89:

Line 86:

* Compatible with unprotected 21700 battery only (Max. battery length: 70.3 mm).

|-

|}

==Technical specification==

{| class="wikitable"

|-

| '''Power input''' ||

*5Vdc 5A via USB-C (Input current below 5A may cause improper operation)

|-

| '''UPS output''' ||

*5.1V ±5% Max 5A

|-

| '''Battery charging current''' ||

*1.5A

|-

| '''Terminal Battery Voltage''' ||

*4.23V

|-

| '''Battery Recharge Threshold''' ||

*4.1V

|-

| '''Ports & Connectors''' ||

*USB-C power in connector x1

*1-cell 21700 battery connector x1

*SSD socket - M.2 KEY-M 67P x1

*40-pin extended GPIO header x1

|-

| '''PCB Size''' ||

*86.5mm x 84.5mm

|}

Line 97:

Line 122:

* 4x M2.5x13.5mm F/F Spacers

* 1x Screw Kit

[[File:X1208-IMG-0015-Packing-List.jpg|550px]]

==Script Reference==

==Installation Guide==

*Installation of X1208 and [[X1207-C1]]

:[[File:X1208-X1207-C1-Install-guide.jpg|800px]]

Installation Video for Raspberry Pi 5+[[X1208]]+[[X1207-C1]]: https://youtu.be/JVkKT1Gh4xo

==Matching Case==

~~There~~ is ~~no matching~~ case for X1208 ~~right now! Please looking forward to the future update~~.

The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5''' [[ X1207]]'''/[[X1208]] UPS Shield, offering robust protection in a sleek, black aesthetic.

* Case dimension: 92.8 x 90.8 x 42.8 mm

X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories

X1207-C1-IMG-0167.jpg|X1207-C1

X1207-C1-IMG-0170.jpg|X1207-C1

X1207-C1-IMG-0174.jpg|X1207-C1

</gallery>

==User Manual==

* X1208 Hardware Guide:[https://suptronics.com/Raspberrypi/Power_mgmt/x1208-v1.0_hardware.html X1208 Hardware]

* X1208 Software Guide:[~~https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1208 Software~~]

* X1208 Software Guide: [[#Script Reference]]

==FAQ==

~~~~

Q1: ~~Question 1~~

Q1: Can I use the [https://www.raspberrypi.com/products/ai-hat/ official Raspberry Pi AI HAT] together with the X1208 in the X1207-C1 case?

</div>

A: ~~Place~~ the ~~answer here~~.

A: A: No. The X1208 uses the Raspberry Pi 5 PCIe connector, which is also required by the official Raspberry Pi AI HAT. Since the PCIe interface is already occupied by the X1208, the AI HAT cannot be installed simultaneously.

</div>

<~~comments~~ />

<comment-streams id="main" />

@@ Line 1: / Line 1: @@
 {{GD Template Impl}}
+[[File:X1208-IMG-9926-Interface.jpg|thumb|X1208 V1.0 Interface]]
+[[File:X1208-IMG-0091-1.jpg|thumb|X1208 V1.0]]
+[[File:X1208-IMG-0088.jpg|thumb|X1208 V1.0]]
+[[File:X1208-IMG-0129.jpg|thumb|X1208 V1.0 with Raspberry Pi 5 ]]
+[[File:X1208-IMG-0125-pogo-pin-connection.jpg|thumb|X1208 V1.0]]
+[[File:X1208-IMG-0105-Power.jpg|thumb|X1208 V1.0 with Raspberry Pi 5 & SSD card]]
 ==SAFETY INSTRUCTIONS AND WARNINGS==
-* <span style="color:red;">The default charging current is set to 1.5A and charge cut-off voltage is 4.23V. before connecting your battery to the UPS board, Please carefully confirm the maximum charging current and voltage, exceeding the upper limit of the charging specification that the battery can withstand will not only cause adverse reactions, but may also cause irreversible damage.
+{{UPS Safety Warning}}
-* <span style="color:red;">It is essential to read and understand these safety instructions and warnings before charging your batteries.
-* <span style="color:red;">Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal   injury, and damage to property if charged or used improperly.
-* <span style="color:red;">Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the   battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
-* <span style="color:red;">Do not mix and use old batteries with new batteries, or batteries with different brand names.
-* <span style="color:red;">Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when   they are two years old, whichever comes first.
-* <span style="color:red;">When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material   or carpet unattended.
-* <span style="color:red;">Keep the UPS shield away from children to ensure their safety.
 ==Overview==
@@ Line 62: / Line 62: @@
 * High-efficiency converter delivers 3.5A to your SSD
-'''Compatible Accessories'''
-* [[X1100]] USB3 to SATA 2.5 HDD/SSD shield for Pi 5
-* Other add-on boards that do not use the PCIe interface are attached to the bottom of the Raspberry Pi 5.
 |-
 | '''Spec''' ||
@@ Line 89: / Line 86: @@
 * Compatible with unprotected 21700 battery only (Max. battery length: 70.3 mm).
 |-
+|}
+==Technical specification==
+{| class="wikitable"
+|-
+| '''Power input''' ||
+*5Vdc 5A via USB-C (Input current below 5A may cause improper operation)
+|-
+| '''UPS output''' ||
+*5.1V ±5% Max 5A
+|-
+| '''Battery charging current''' ||
+*1.5A
+|-
+| '''Terminal Battery Voltage''' ||
+*4.23V
+|-
+| '''Battery Recharge Threshold''' ||
+*4.1V
+|-
+| '''Ports & Connectors''' ||
+*USB-C power in connector x1
+*1-cell 21700 battery connector x1
+*SSD socket - M.2 KEY-M 67P x1
+*40-pin extended GPIO header x1
+|-
+| '''PCB Size''' ||
+*86.5mm x 84.5mm
 |}
@@ Line 97: / Line 122: @@
 * 4x M2.5x13.5mm F/F Spacers
 * 1x Screw Kit
+[[File:X1208-IMG-0015-Packing-List.jpg|550px]]
+==Script Reference==
+{{X120x Series UPS Script Reference}}
+==Installation Guide==
+*Installation of X1208 and [[X1207-C1]]
+:[[File:X1208-X1207-C1-Install-guide.jpg|800px]]
+Installation Video for Raspberry Pi 5+[[X1208]]+[[X1207-C1]]: https://youtu.be/JVkKT1Gh4xo
+{{#ev:youtube|https://youtu.be/JVkKT1Gh4xo}}
 ==Matching Case==
-There is no matching case for X1208 right now! Please looking forward to the future update.
+The [[X1207-C1]] is a premium metal case specially designed for the Raspberry Pi 5''' [[ X1207]]'''/[[X1208]] UPS Shield, offering robust protection in a sleek, black aesthetic.
+* Case dimension: 92.8 x 90.8 x 42.8 mm
+<gallery>
+X1207-C1-IMG-0165-Packing List.jpg|X1207-C1 Accessories
+X1207-C1-IMG-0167.jpg|X1207-C1
+X1207-C1-IMG-0170.jpg|X1207-C1
+X1207-C1-IMG-0174.jpg|X1207-C1
+</gallery>
 ==User Manual==
 * X1208 Hardware Guide:[https://suptronics.com/Raspberrypi/Power_mgmt/x1208-v1.0_hardware.html X1208 Hardware]
-* X1208 Software Guide:[https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1208 Software]
+* X1208 Software Guide: [[#Script Reference]]
 ==FAQ==
-<!-- 这里提供了一个Q&A的模板，增加Q&A时按照下面的格式写就可以了 -->
 <div class="toccolours mw-collapsible mw-collapsed">
 <div style="font-weight:bold;line-height:1.0;">
-Q1: Question 1
+Q1: Can I use the [https://www.raspberrypi.com/products/ai-hat/ official Raspberry Pi AI HAT] together with the X1208 in the X1207-C1 case?
 </div>
 <div class="mw-collapsible-content">
-A: Place the answer here.
+A: A: No. The X1208 uses the Raspberry Pi 5 PCIe connector, which is also required by the official Raspberry Pi AI HAT. Since the PCIe interface is already occupied by the X1208, the AI HAT cannot be installed simultaneously.
 </div>
 </div>
 <!--Add review function! -->
-<comments />
+<comment-streams id="main" />
 <!--Please choose the  -->