Open main menu
Geekworm Wiki

Comments log

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 14:32, 14 March 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Maybe we can not understand your meaning clearly.Can you contact us by email and attach some photo or details? Best regards, Cindy/Geekworm)
  • 11:50, 14 March 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Could you please check if your battery 2pin port the red and black cable if in the right place as the photo above. Or you can change another 3.7v battery to have a try. Best regards, Cindy/Geekworm)
  • 11:18, 14 March 2019 Admin talk contribs posted a new comment on RPi UPSPack (Hello friend, For the PONIT 3:3- After, the battery begins to discharge, but the red LED remains fixed and the charging is no longer started, so the battery is completely discharged and the Raspberry Pi stops - KO. How do you connect each device? Plea...)
  • 04:00, 14 March 2019 109.151.141.225 talk posted a new comment on Raspi UPS HAT Board (Hello, my UPS HAT when fully charged and on power will stop the ouput power to raspberry pi then start again then stop. Is this normal when fully charged and on power ? Thank you)
  • 17:58, 13 March 2019 62.15.136.19 talk posted a new comment on RPi UPSPack (Hello! I have a problem: 1- Feed the UPS and connect a Raspberry Pi. Everything works and indicates that the battery is charging (red LED flashes) - OK. 2- After a while, the red led stays fixed (battery charged) - OK. 3- After, the battery begins to d...)
  • 14:16, 13 March 2019 202.46.129.70 talk posted a new comment on Raspi UPS HAT Board (how can i calibrate the battery? from the LED indicator it still blink (2 LEDs), but from the program shows 0%, then about in hour, my Raspi run out of battery)
  • 09:51, 6 March 2019 Admin talk contribs posted a new comment on 2.8 inch Touch Screen for Pi zero (Hi, Thanks for your file, but our 2.8 inch screen is not waveshare product, please note, thank you very much. Best regards, Cindy/Geekworm)
  • 17:03, 5 March 2019 102.248.105.97 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (Kindly include the instructions for this product on this same page for others gpio pwmc 1 # set clock 1000 makes noise for me gpio -g mode 18 pwm # enable PWM on GPIO18 gpio -g pwm 18 1010 # change screen brightness to 975 range 0 - 1024...)
  • 11:51, 4 March 2019 Admin talk contribs posted a new comment on 3.2 Inch TFT Lcd Touch Screen SKU:340835 (Hello sir, The 3.2 inch screen has been discontinued now, and all the information are on the page, we can not get any more detils now, sorry! Best regards, Cindy/Geekworm)
  • 16:45, 2 March 2019 62.143.143.243 talk posted a new comment on 3.2 Inch TFT Lcd Touch Screen SKU:340835 (Is there a a way to dim the backlight ?)
  • 10:35, 27 February 2019 Admin talk contribs posted a new comment on X820 (Hello, We suggest that you refer to here on the official site about How to boot from a USB mass storage device on a Raspberry Pi: https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md Best regards, Cindy)
  • 03:54, 27 February 2019 121.200.15.236 talk posted a new comment on X820 (Hi All Once the HDD is installed, can I boot from a USB Stick to install Linux onto the internal HDD as it is or are other commands/configuration needed as of 1/2/2019? I know some commands previously were needed.)
  • 18:31, 26 February 2019 Admin talk contribs posted a new comment on X730 (Hello sir, we will release the X735 and the matching case for X820+x735 soon. Harry /Geekworm)
  • 14:21, 25 February 2019 Admin talk contribs posted a new comment on Robot Expansion Board (Hello dear friend, You can modify the I2C address by shortcut the A0~A3 on the board (shortcut A0 and A1, shortcut A1 and A2...), thus you can get the different I2C address. But we do not test or try this, hope to get your understanding!)
  • 03:49, 25 February 2019 76.126.103.90 talk posted a new comment on Robot Expansion Board (Is there a way to stack two of the Motor HAT in order to be able to drive 4 stepper motors ?)
  • 16:17, 23 February 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, The UPS HAT board is with standard Raspberry Pi Pi HAT size!)
  • 13:48, 23 February 2019 112.215.175.209 talk posted a new comment on Raspi UPS HAT Board (what dimension of board?)
  • 09:39, 21 February 2019 Admin talk contribs deleted comment #202 on PINE A64
  • 09:39, 21 February 2019 Admin talk contribs posted a new comment on PINE A64 (Hello sir, We suggest that you can ask for help from the official website: https://support.pine64.org/portal/home Best regards, Geekworm)
  • 09:32, 21 February 2019 Admin talk contribs posted a new comment on PINE A64 (Hello sir, We suggest that you can ask for help from the official website: https://support.pine64.org/portal/home Best regards, Geekworm)
  • 09:29, 21 February 2019 Admin talk contribs posted a new comment on X820 (Hello sir, For the Raspberry Pi 3B+ turorial you need to refer to raspberry pi official site. https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md The abvove page is mainly turorial for Raspberry Pi X820 board.)
  • 01:26, 21 February 2019 64.33.242.15 talk posted a new comment on PINE A64 (I have 2 of the first model's both with 2 gig ram and both with the add-on bluetooth and wifi cards. One is mounted in a sort of tablet setup running Android, the other in a clear semi-case, it had a screen set atop it but the wires ripped so now I ac...)
  • 17:45, 20 February 2019 104.194.218.185 talk posted a new comment on X820 (Hi, Is this the same turorial for the Raspberry P3b+ ?)
  • 11:24, 20 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hello, GTX 1050 or GTX 1050TI or AMD CARD is not recommend to use. Do you try the The list of recommended graphics card: GTX650 GTX660 GTX670 GTX750 GTX760 GTX950 GTX960 GTX970 GTX980 GTX1060 GTX1070 GTX1080 ?)
  • 02:53, 20 February 2019 72.180.93.212 talk posted a new comment on EXP GDC (I’ve been trying to help a friend install a GTX 1050 egpu on his HP 8470p EliteBook (which is a laptop on the supported list). He has 8 gigabytes of ram and an integrated HD 5000 graphics chip. He has tried both the Mini PCI-E version and the express...)
  • 08:53, 15 February 2019 Admin talk contribs posted a new comment on Raspi UPS HAT Board (Hello, Could you please show some more details? Please attached some photos about your data. You can contact us by support@geekworm.com , please tell us your order number and product link of where you buy it, thanks!)
  • 21:09, 14 February 2019 213.227.32.73 talk posted a new comment on Raspi UPS HAT Board (Hello, when I measure the battery capacity I get values over 100%. For this measure I use the formula that appear in this document "File:How-to-use-via-i2c.pdf". I'm missing something?)
  • 11:18, 14 February 2019 Admin talk contribs posted a new comment on X830 (Hi, You can get it at our official site: https://geekworm.com/products/raspberry-pi-x830-3-5-inch-sata-hdd-hard-disk-drive-storage-expansion-board)
  • 18:26, 13 February 2019 178.78.224.56 talk posted a new comment on X830 (hur kan jag skaffa X830 moderkort till case)
  • 15:28, 13 February 2019 84.219.193.22 talk posted a new comment on X830 (hur kan jag skaffa det)
  • 15:27, 13 February 2019 84.219.193.22 talk posted a new comment on X830 (jag söker efter ett sånt kort http://www.raspberrypiwiki.com/index.php/File:IMG_4253-3B-Plus.jpg)
  • 09:03, 13 February 2019 Admin talk contribs posted a new comment on X400 (Hello, There is no information show this board can be remote control.)
  • 00:11, 13 February 2019 213.205.194.137 talk posted a new comment on X400 (How do i setup a remote control to use with this board??)
  • 16:38, 12 February 2019 Admin talk contribs posted a new comment on RPi IR-CUT Camera (Hi, Sorry, we can not confirm about this.)
  • 16:35, 12 February 2019 Admin talk contribs posted a new comment on Armor Case (Hi, Please refer to here: https://geekworm.com/products/raspberry-pi-aluminium-alloy-metal-armor-cooling-case-with-dual-fan It is very easy to install. Best regards, Cindy/Geekworm)
  • 16:34, 12 February 2019 Admin talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Sorry, we can not confirm about if this board can convert any LVDS data to RAW HDMI out.)
  • 16:32, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Which version does my laptop use? Hi,Thanks for your email. 1. The EXP GDC has to be used with the built-in wireless card. 2. Your laptop has to be disassembled to comfirm the interface type if no Expresscard interface. 3. Different versions, the inter...)
  • 16:31, 12 February 2019 Admin talk contribs deleted comment #183 on EXP GDC
  • 16:31, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, EXP GDC is a DIY product, we suggest you can google to find more useful information.)
  • 16:31, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, EXP GDC is a DIY product, we suggest you can google to find more useful information.)
  • 16:30, 12 February 2019 Admin talk contribs posted a new comment on EXP GDC (Hi, Sorry, we do not test it.)
  • 16:29, 12 February 2019 Admin talk contribs posted a new comment on X820 (Hello, Please refer to: http://www.raspberrypiwiki.com/index.php/X830_V2.0 This X830 V2.0 board support to install 3.5 inch SATA HDD, and with a match metal case. Best regards, Cindy/Geekworm)
  • 16:26, 12 February 2019 Admin talk contribs posted a new comment on X850 (Hello, Please see the first photo on the right, it is Micro USB DC 5V. Best regards, Cindy/Geekworm)
  • 16:18, 12 February 2019 Admin talk contribs deleted comment #178 on X830
  • 16:18, 12 February 2019 Admin talk contribs posted a new comment on X830 (Hello, Sorry, the X830 has USB3.0 port but now the Raspberry Pi only support USB2.0, so the transfer rates will be USB2.0. Maybe in the future the Raspberry Pi 4 will support USB3.0. Best regards, Cindy/Geekworm)
  • 16:17, 12 February 2019 Admin talk contribs posted a new comment on X830 (Hello, Sorry, the X830 has USB3.0 port but now the Raspberry Pi only support USB2.0, so the transfer rates will be USB2.0. Maybe in the future the Raspberry Pi 4 will support USB3.0. Best regards, Cindy/Geekworm)
  • 16:14, 12 February 2019 Admin talk contribs deleted comment #176 on X350
  • 16:14, 12 February 2019 Admin talk contribs posted a new comment on X350 (Hello, The X350 and Raspberry Pi is connected by the USB bridge, does not require external power supply for X350, and we upload the X350 board diagram above, please check the details. Best regards, Cindy/Geekworm)
  • 16:14, 12 February 2019 Admin talk contribs posted a new comment on X350 (Hello, The X350 and Raspberry Pi is connected by the USB bridge, does not require external power supply for X350, and we upload the X350 board diagram above, please check the details. Best regards, Cindy/Geekworm)
  • 15:54, 12 February 2019 Admin talk contribs deleted comment #174 on X150
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"