Open main menu
Geekworm Wiki

Comments log

This is a log of comments.

Logs
(newest | oldest) View (newer 50 | ) (20 | 50 | 100 | 250 | 500)
  • 00:08, 14 July 2025 90.222.31.126 talk posted a new comment on X1009 (All of a sudden, my X1009 is no longer recognized by my Pi. the powerLED on the shield remains red.)
  • 22:27, 12 July 2025 213.204.198.14 talk posted a new comment on X306 (I have both v1.2 and v1.3. I have been looking for what the changes there have been made between v1.1 and v1.2. There is printed v1.2 on the bottom of the circuit board so I would like to know what have been made from the documented 1.1 version. The batteryholder of the v1.3 seems to be very weak because mine broke when I pressed the battery into place. No problem with the function but like to mention it as I have seen others have the same issue. Great board but it would have been very good...)
  • 12:04, 10 July 2025 Lisa talk contribs posted a new comment on X885 (Sorry, we can't fulfill both conditions, maybe you can refer to the feedback here, hope it helps.NASPi_Gemini_2.5#comment-2720)
  • 05:22, 10 July 2025 71.38.166.74 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (what are you using for SSD and what did you do to get it to boot. I can not get HAOS to boot from SSD and i feel like i have tried everything. i am using the x1015 on my pi 5)
  • 23:34, 9 July 2025 178.255.168.32 talk posted a new comment on X885 (Sorry, but I don't care about other users' feedbacks. I need to be able to put disks to sleep, regardless of other users' opinions. As a customer, I would expect to be in control of the device I purchased from you. If you have any unofficial/unpublished firmware/code, I would ask that you send it to me.)
  • 10:53, 9 July 2025 Lisa talk contribs posted a new comment on X885-software (Hello, According to user feedback, it needs to be running all the time. Standby is no longer supported, which will cause more problems. Hope to get your understanding.)
  • 10:52, 9 July 2025 Lisa talk contribs posted a new comment on X885 (Hello, According to user feedback, it needs to be running all the time. Standby is no longer supported, which will cause more problems. Hope to get your understanding.)
  • 08:51, 9 July 2025 178.255.168.32 talk posted a new comment on X885 (Is there any way how to activate standby on HDDs? They are constantly running, even that it is not needed in the time.)
  • 08:27, 9 July 2025 178.255.168.32 talk posted a new comment on X885-software (Is there any way how to activate standby on HDDs? They are constantly running, even that it is not needed in the time.)
  • 22:55, 8 July 2025 185.204.53.98 talk posted a new comment on X1002 (And the problem is that this device fails after some time, though it passes all the health checks and allows itself to be partitioned (unlike NV3) dmesg: [ 39.925583] nvme nvme0: controller is down; will reset... [ 40.009594] nvme nvme0: Disabling device after reset failure: -19 Adding "nvme_core.default_ps_max_latency_us=0 pcie_aspm=off pcie_port_pm=off" to cmdline didn't help too. All that was done by testing on latest eeprom with latest rpi-6.12.y linux tree)
  • 22:53, 8 July 2025 185.204.53.98 talk posted a new comment on X1002 (Hello, it's me again. Nevermind, the NV2 seems to be incompatible too. This manufacturer is known for swapping chips from batch to batch, and I maybe I got the Phison controller if I can judge correctly: drk@drk-pi:~ $ sudo nvme id-ctrl -H /dev/nvme0n1 NVME Identify Controller: vid : 0x2646 ssvid : 0x2646 sn : 50026B7686C65AD9 mn : KINGSTON SNV2S1000G fr : SBM02106 rab : 6 ieee : 0026b7 cmic : 0 [3:3] : 0...)
  • 18:52, 7 July 2025 Lisa talk contribs posted a new comment on X1011 (Hello, Sorry, we don't have a compatible list, but based on user feedback we have compiled some incompatible lists, please refer to NVMe SSD boot with the Raspberry Pi 5 ； You can also refer to other users' feedback on compatible SSDs.)
  • 18:41, 7 July 2025 Lisa talk contribs posted a new comment on X1002 (Hello, Thanks for your feedback, we have added Kingston NV3 NVME to the incompatibility list.)
  • 18:12, 7 July 2025 Lisa talk contribs posted a new comment on X1202 (Hello,We have received your email and will reply to your question via email.)
  • 16:56, 7 July 2025 176.59.105.33 talk posted a new comment on X1002 (Hello, it's me again. * Kingston NV2 definitely works. No high pitch noise either! * This additionally confirms that Kingston NV !3! is incompatible with this HAT * In my previous comment I've made a typo. Of course i meant that I tried NV3 with PCIe 2 & 3 Gen configs with no success.)
  • 10:25, 7 July 2025 206.176.133.226 talk posted a new comment on X1500 ($ sudo sh -c 'echo 1 > /sys/devices/platform/cooling_fan/hwmon/hwmon2/pwm1_enable' $ sudo sh -c 'echo 128 > /sys/devices/platform/cooling_fan/hwmon/hwmon2/pwm1' $ sudo sh -c 'echo 255 > /sys/devices/platform/cooling_fan/hwmon/hwmon2/pwm1' $ cat /sys/class/thermal/thermal_zone0/temp 64450 $ sudo vcgencmd measure_temp temp=62.6'C thats what i use to control the fan speed manually , if that ever help someone .)
  • 23:12, 6 July 2025 88.202.249.32 talk posted a new comment on X1202 (I am using the X1202, with 4 batteries installed, and plugged in a good 5V 5A power supply. Under a moderate load, after 30 seconds the RPI shuts down. I have therefore tested it WITHOUT batteries, and the RPI shuts down after a few seconds while booting! Is this normal behaviour? Should not the X1202 be able to run WITHOUT batteries? The power supply is good: when plugged into the RPI directly it works fine.)
  • 09:36, 6 July 2025 71.127.59.68 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (Did you ever get your SN580 working? I am 40 hours into trying to get them work with an X1005. :()
  • 21:55, 5 July 2025 203.115.120.178 talk posted a new comment on X1011 (I want a list of supported M.2 NVMe SSDs which can be used with X1011. Any help is appreciated.)
  • 09:09, 5 July 2025 191.95.146.101 talk posted a new comment on EDP to HDMI Adapter (You should check whether the video output is 4-lane or 2-lane. Version 1.3 of the card includes a switch that allows you to select this option.)
  • 09:06, 5 July 2025 191.95.146.101 talk posted a new comment on EDP to HDMI Adapter (Hello, every time you connect or disconnect eDP connections, you must do so from a cold start. Make sure both the battery and the voltage adapter are disconnected during the process. Once the connection is secure, you can energize the circuit; otherwise, you risk causing a short circuit.)
  • 22:17, 4 July 2025 49.192.144.55 talk posted a new comment on X1001 (Hi, I'm trying to clone my same size 2TB old USB SSD drive to the NVME PCIe Gen4 drive on a Raspberry Pi 5 using the RaspbianOS "SD Card Copier". The drive has 6 small partitions and one large one with about 1.5TB. The cloning creates all partitions just fine, it also boots from the new drive but it copies only about 60GB from the large partition. I tried the cloning again and the same thing happened but this time I could briefly see a message pop up during the cloning process saying tha...)
  • 08:55, 4 July 2025 176.59.105.33 talk posted a new comment on X1002 (It's totally incompatible with Kingston NV3 NVME. First of all - high pitch noise when idling. I've tried battling it with software methods with no success. Second, it does not get formatted/partitioned reliably. In 9/10 cases it just hangs and crashes the whole rPi. Sometimes, the X1002's blue light stays on. Sometimes, the lights go off in these cases. Either way, it hangs. Tried both in PCIe 2 & PCIe 2 Modes. Will have to try other NVME. Maybe, will try my luck with NV2 by the same Kings...)
  • 18:54, 3 July 2025 Lisa talk contribs posted a new comment on X1001 (Hello, Sorry, we have not tested this model.)
  • 18:27, 3 July 2025 213.194.166.147 talk posted a new comment on X1001 (Hello, does the Micron 2450 MTFDKBA1T0TFK work with the X1001?)
  • 11:51, 2 July 2025 59.124.27.148 talk posted a new comment on X1300 Software (How can I enable the streaming function?)
  • 14:54, 26 June 2025 Lisa talk contribs posted a new comment on X1201 (Hi, We received your email with installation pictures. But I can't see the status of the power indicator. And I'm curious why you don't just use the USB C port of X1201? We will reply to your question by email. Please pay attention to the email.)
  • 11:11, 26 June 2025 Lisa talk contribs posted a new comment on X1501 (Hi, please refer to [https://suptronics.com/Raspberrypi/cm5/x1501-v1.0_hardware.html X1501 Hardware]--12-pin configurable header (J2))
  • 11:10, 26 June 2025 Lisa talk contribs deleted comment #5881 on X1501
  • 11:10, 26 June 2025 Lisa talk contribs posted a new comment on X1501 (Hi, please refer to X1501 Software--12-pin configurable header (J2))
  • 05:27, 26 June 2025 73.233.223.6 talk posted a new comment on X1501 (Can we get a pinout and orientation for the 12 pin header?)
  • 22:49, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Make sure youre using good quality 18650 lithium ion batteries. For example, I use OEM samsung batteries. make sure you didnt scratch or peel any traces by accident. If you have a multimeter, you can check battery voltage for if they are failing, and continuity.)
  • 22:48, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (I forgot to mention the polarity is correct and its connected how it should be so i dont get why it wouldnt work, Im newer to the hardware side of computers, sorry)
  • 22:47, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Hey, im using a usb c female with only the power lines connected, the ground and power wires. Yes im trying to power it via the jst connector with a stable psu that can chrage it through the built-in usb c port. If it cant work like this, please give an example on how to use it. I cant provide pictures right now and cant get the order number. anything helps.)
  • 20:00, 25 June 2025 68.197.206.6 talk posted a new comment on X1201 (Update: I'm suspecting that the fully charged batteries are not delivering the full 5v charge to the Pi, but the X1201 does step up a USB-C charge to 5v. -The pogo pins appear to be seated correctly. -When I run ic2detect, the Pi recognizes the x1201 at address36. -When I power the X1201 via USB-C (either 3v or 5v), the PI5 LED lights, and the Pi powers up. -When I power the Pi directly via 5v USB, the X1201 PI5 LED lights But when the X1201 is not connected to USB-C power, if I press...)
  • 18:11, 25 June 2025 Lisa talk contribs posted a new comment on X1201 (H,[2 pin usb C connector] ？ --Do you want to power it via [5V power input XH2.54-2P]? If yes, what power supply are you using and how are you connected? Please email us. Provide pictures and your order number. info@geekworm.com)
  • 17:57, 25 June 2025 Lisa talk contribs posted a new comment on X1001 (Hi, Sorry, we are not sure, you can refer to the official documentation.)
  • 09:01, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Attempt to reseat the ups. Make sure the pogo pins are aligned correctly with each pin. Can you tell me if when you tunr it on, the LED thats labled "PI5" is on. that shows if the pi is detected. It can be tricky to know if the pins are aligned correctly, make sure theres a good connection. If it doesnt sense a pi connected to it, it will turn off after a few seconds as stated on the wiki.)
  • 07:57, 25 June 2025 68.197.206.6 talk posted a new comment on X1201 (Hi, I have the X1201 connected to my Raspberry Pi 5. When I connect to USB-C, the Pi powers up. When I am not connected to USB-C, when I press the power button on the X1201, the LEDs on the X1201 show the batteries are fully charged and that the Pi is connected. The green Pi LED lights briefly, and then the Pi goes into standby mode with a red LED. I have not changed anything in the Pi setup - I'm using a stock install of the latest Pi OS. What should I do?)
  • 06:55, 25 June 2025 173.54.57.150 talk posted a new comment on X1201 (Sorry lol, last question, how do I get the 5v in to work. Ive soldered a 2 pin usb C connector for power, but im not getting any sign. how is it used? please give an example. Thanks!)
  • 03:09, 25 June 2025 92.212.9.220 talk posted a new comment on X1001 (I have been running a WD SN770M for about 3-4 days on a somewhat idle Nextcloud install with it not crashing since I adjusted the bootloader settings with "dtparam=pciex1_gen=3,aspm=off". Is setting this alright or discouraged? If the latter, why?)
  • 18:14, 24 June 2025 Lisa talk contribs posted a new comment on X1009 (Hi, yes, you can power the RPi5 via Type C. because X1009 needs the V3.0V control of the RPi5，can not disconnect it all. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) .)
  • 18:14, 24 June 2025 Lisa talk contribs deleted comment #5868 on X1009
  • 18:14, 24 June 2025 Lisa talk contribs posted a new comment on X1009 (Hi, yes, you can power the RPi5 via Type C. You need to unplug the pins of PIN2 and PIN4 of expansion header (GPIO bridge connector) . because X1009 needs the V3.0V control of the RPi5，can not disconnect it all.)
  • 17:22, 24 June 2025 Lisa talk contribs posted a new comment on X1008 (Hi,X1008 does not support the auto power-on.)
  • 14:31, 24 June 2025 173.70.167.178 talk posted a new comment on X1009 (> Hello, does not support power X1009 via Type C of RPi5. Thanks for your answer, Lisa! So I need to disconnect GPIO bridge connector if I want to power PI and X1009 separately? As documentation says: Don't power the X1009 via DC powe jack and the Raspberry Pi5 via USB-C at the same time. Just power the X1009, and then the X1009 will power the Pi 5 via the GPIO.)
  • 23:12, 23 June 2025 195.224.89.36 talk posted a new comment on X1008 (Hi, the board doesn't power on by itself after connecting the supply, it requires pressing the button. Can it be made to power automatically? This would be a lot better in case of power outage when there is no one home.)
  • 15:09, 23 June 2025 Lisa talk contribs posted a new comment on X1009 (Hello, does not support power X1009 via Type C of RPi5.)
  • 14:38, 23 June 2025 Lisa talk contribs posted a new comment on X1201 (Hi,The external power switch function is the same as the onboard switch.)
  • 05:13, 21 June 2025 173.70.167.178 talk posted a new comment on X1009 (Is it possible to power the Raspberry Pi 5 via a USB Type-C cable, while powering HDDs directly from an independent 12V power supply? In that case, will the Raspberry Pi 5 still be able to power the X1009 over GPIO — essentially in reverse? The DC 12V 5.5x2.1mm power input would not be used in this setup. If that is not possible, then I will need to use two 12V power supplies: - one 12V power supply for the X1009 (and Raspberry Pi 5) - another 12V power supply for the HDDs. The reason I'm...)
(newest | oldest) View (newer 50 | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"