Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
26 May 2024
|
|
07:10 | (Comments log)[58.29.55.98; 47.158.215.169 (2×)] | |||
|
|
07:10 58.29.55.98 talk posted a new comment on T208-hardware (It was qualified 5V 4A Adapter) | ||||
|
|
02:38 47.158.215.169 talk posted a new comment on X1001 (Sorry scratch that, still seems to fail with heavy disk usage) | ||||
|
|
00:09 47.158.215.169 talk posted a new comment on X1001 (I can confirm updating the firmware seems to work on the pi5. Have a WD black SN770. Worked with USB, didn't work with the NVMe hat. Originally would boot very slow, and couldn't reliably launch a terminal, or a web browser at all. System would freeze or go to gray screen/black screen. Booted with the drive in a USB enclosure and went to raspi-config and loaded new bootloader/firmware through the advanced options, reinstalled the drive into the hat and now boots fine, fast, and can lau...) | ||||
25 May 2024
| 11:54 | Comments log 49.228.92.160 talk posted a new comment on X1203 (What flat li-po battery would you recommend (Except 18650)? Does the max li-po have to 3000mah? Is a 3000mah 3.7v lipo good enough?) | ||||
24 May 2024
| 02:05 | Comments log 209.93.62.177 talk posted a new comment on X1003 (Working well for me, after installing the PCIE cable the wrong way round initially. Using an "SkHynix 256GB PCIe NVMe 2242 SSD (HFM256GD3HX015N) (OEM)" off Amazon. lspci says "0000:01:00.0 Non-Volatile memory controller: SK hynix Gold P31/PC711 NVMe Solid State Drive") | ||||
22 May 2024
| 06:47 | Comments log 23.93.48.84 talk posted a new comment on X1202 (Will this provide power if only 2 batteries are installed? I don't need the capacity of 4 18650s, but having a place to store and charge spares would be nice.) | ||||
21 May 2024
|
|
05:51 | (Comments log)[23.114.212.80; 178.237.217.243] | |||
|
|
05:51 178.237.217.243 talk posted a new comment on N508 (How much room does it have for SSD heatsink?) | ||||
|
|
04:14 23.114.212.80 talk posted a new comment on X1202 (Is there a way to run the pi5 off of the 5v out XH connector? Due to size constraints I cannot use the pogo pins. If I need to solder connectors from the GPIO to the Pogo pins, which ones are necessary for minimal function?) | ||||
20 May 2024
|
|
05:19 | (Comments log)[95.133.95.89; 68.197.140.117; 73.16.134.38 (2×)] | |||
|
|
05:19 68.197.140.117 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (You have the WD SN580 listed as "WD Green", when that model ls actually a WD Blue.) | ||||
|
|
03:52 73.16.134.38 talk posted a new comment on X728 (OK, sorry, I figured it out. I was trying to follow the schematic from the 4-pin LED momentary push button, but everything works as expected if you follow what the Wiki suggests. The LED button has four pins: S1, S2, LED+, LED- The x728 has four pins: PWR, GND, GND, LED+ Connect them as such: PWR - S1 GND - S2 GND - LED- LED+ - LED+ I don't know why my incorrect wiring ever worked, but this is what it always should have been. Leaving this here in case anyone else has the same problem!) | ||||
|
|
01:25 73.16.134.38 talk posted a new comment on X728 (Small update: I compared the status of all GPIO pins with and without the button pressed, and none change (including 5, 13, and 26).) | ||||
|
|
01:17 95.133.95.89 talk posted a new comment on X735 (Hello. What happens if you short L-SW and Auto On at the same time?) | ||||
19 May 2024
|
|
23:46 | (Comments log)[73.16.134.38; 178.237.217.243] | |||
|
|
23:46 73.16.134.38 talk posted a new comment on X728 (Hello, apologies for the dumb question: my external power button correctly turns the board on, and "x728off" works, but the external power button stopped working to turn the board off recently. I think I may have accidentally deleted a script or service. However, I cannot figure it out. I am using V1.3. I tried following your software tutorial, but it only seems to make "x728off" work. If you can tell me how the 4-pin external power button works, I can write a script to make it work for me a...) | ||||
|
|
20:09 178.237.217.243 talk posted a new comment on X1011 (Will it fit NASPi Alu case? What case is it supposed to be used with?) | ||||