X1009: Difference between revisions

(4 intermediate revisions by 2 users not shown)

Line 84:

==User Manual==

* Dimensions source file (DXF): [[File:X1009-V1.0.dxf]] - You can view it with [https://viewer.autodesk.com/ Autodesk Viewer] online

===Hardware===

[[File: X1009v1.1-dwg.png | 700px]]

[[File:X-1009-V1.1-install.jpg | 700px]]

Line 130:

'''1. Root Cause'''

:The problem is triggered by ''upstream Linux kernel code changes''. The JMicron JMB585 controller chip equipped on the SATA hat has potential data corruption risks when running under 64-bit DMA mode on certain platforms. Therefore, the kernel forces this chip to work with 32-bit DMA mode. Without matching configuration adjustment, the system cannot probe and identify SATA disks via AHCI protocol normally.

:The problem is triggered by ''upstream Linux kernel code changes''. The '''JMicron JMB585 controller chip''' equipped on the SATA hat has potential data corruption risks when running under 64-bit DMA mode on certain platforms. Therefore, the kernel forces this chip to work with 32-bit DMA mode. Without matching configuration adjustment, the system cannot probe and identify SATA disks via AHCI protocol normally.

'''2. Affected System & Kernel Versions'''

Line 137:

'''3. Configuration'''

:3-1. Manual Configuration Fix ''(Solution 1)''

:3.1 Manual Configuration Fix ''(Solution 1 - Recommand)''

::Open the config file via terminal command:

::<code>sudo nano /boot/firmware/config.txt</code>

Line 146:

::Multiple dtoverlay entries are allowed, just write each on separate lines.

::Save and exit the editor.

:3-2. One-click Command to Add Configuration ''(Solution 2)''

:3.2 One-click Command to Add Configuration ''(Solution 2 - For reference, '''NOT''' tested by us)''

::Run this command directly in terminal to automatically insert the required setting:

::<code>grep -qxF 'dtoverlay=pcie-32bit-dma-pi5' /boot/firmware/config.txt || sudo sed -i -zE 's/(.*\ndtparam=[^\n]*pciex1[^\n]*)/\1\ndtoverlay=pcie-32bit-dma-pi5/' /boot/firmware/config.txt</code>

Line 154:

:Reboot your Raspberry Pi 5 device after modifying the configuration. The new setting will take effect during startup, and the SATA hat will detect disks properly again.

'''5. Plus:''' Please refer to the [https://forum.openmediavault.org/index.php?thread/59049-psa-rpi5-users-of-the-radxa-sata-hat-now-need-to-use-dtoverlay-pcie-32bit-dma-pi/ original link]. The chip equipped on X1009 is the same as that of the author's Radxa Penta SATA HAT, both adopting JMicron JMB585.

'''5. Plus:'''

:Please refer to the [https://forum.openmediavault.org/index.php?thread/59049-psa-rpi5-users-of-the-radxa-sata-hat-now-need-to-use-dtoverlay-pcie-32bit-dma-pi/ original link]. The chip equipped on X1009 is the same as that of the author's '''Radxa Penta SATA HAT''', both adopting JMicron JMB585.

:Thanks to users who reported issues in the comments. Your feedback helps us improve and update product documents.

</div>

Line 160:

Line 162:

<~~comments~~ />

<comment-streams id="main" />

@@ Line 84: / Line 84: @@
 ==User Manual==
 * Dimensions source file (DXF): [[File:X1009-V1.0.dxf]] - You can view it with [https://viewer.autodesk.com/ Autodesk Viewer] online
 ===Hardware===
 [[File: X1009v1.1-dwg.png | 700px]]
 [[File:X-1009-V1.1-install.jpg | 700px]]
@@ Line 130: / Line 130: @@
 '''1. Root Cause'''
-:The problem is triggered by ''upstream Linux kernel code changes''. The JMicron JMB585 controller chip equipped on the SATA hat has potential data corruption risks when running under 64-bit DMA mode on certain platforms. Therefore, the kernel forces this chip to work with 32-bit DMA mode. Without matching configuration adjustment, the system cannot probe and identify SATA disks via AHCI protocol normally.
+:The problem is triggered by ''upstream Linux kernel code changes''. The '''JMicron JMB585 controller chip''' equipped on the SATA hat has potential data corruption risks when running under 64-bit DMA mode on certain platforms. Therefore, the kernel forces this chip to work with 32-bit DMA mode. Without matching configuration adjustment, the system cannot probe and identify SATA disks via AHCI protocol normally.
 '''2. Affected System & Kernel Versions'''
@@ Line 137: / Line 137: @@
 '''3. Configuration'''
-:3-1. Manual Configuration Fix <span style="color:red;">''(Solution 1)''</span>
+:3.1 Manual Configuration Fix <span style="color:red;">''(Solution 1 - Recommand)''</span>
 ::Open the config file via terminal command:
 ::<code>sudo nano /boot/firmware/config.txt</code>
@@ Line 146: / Line 146: @@
 ::Multiple dtoverlay entries are allowed, just write each on separate lines.
 ::Save and exit the editor.
-:3-2. One-click Command to Add Configuration <span style="color:red;">''(Solution 2)''</span>
+:3.2 One-click Command to Add Configuration <span style="color:red;">''(Solution 2 - For reference, '''NOT''' tested by us)''</span>
 ::Run this command directly in terminal to automatically insert the required setting:
 ::<code>grep -qxF 'dtoverlay=pcie-32bit-dma-pi5' /boot/firmware/config.txt || sudo sed -i -zE 's/(.*\ndtparam=[^\n]*pciex1[^\n]*)/\1\ndtoverlay=pcie-32bit-dma-pi5/' /boot/firmware/config.txt</code>
@@ Line 154: / Line 154: @@
 :Reboot your Raspberry Pi 5 device after modifying the configuration. The new setting will take effect during startup, and the SATA hat will detect disks properly again.
-'''5. Plus:''' Please refer to the [https://forum.openmediavault.org/index.php?thread/59049-psa-rpi5-users-of-the-radxa-sata-hat-now-need-to-use-dtoverlay-pcie-32bit-dma-pi/ original link]. The chip equipped on X1009 is the same as that of the author's Radxa Penta SATA HAT, both adopting JMicron JMB585.
+'''5. Plus:'''
+:Please refer to the [https://forum.openmediavault.org/index.php?thread/59049-psa-rpi5-users-of-the-radxa-sata-hat-now-need-to-use-dtoverlay-pcie-32bit-dma-pi/ original link]. The chip equipped on X1009 is the same as that of the author's '''Radxa Penta SATA HAT''', both adopting JMicron JMB585.
+:Thanks to users who reported issues in the comments. Your feedback helps us improve and update product documents.
 </div>
 </div>
@@ Line 160: / Line 162: @@
 <!--Add review function! -->
-<comments />
+<comment-streams id="main" />
 <!--Please choose the  -->