Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
20 October 2024
|
|
15:04 | (Comments log)[94.31.91.145; 58.88.94.85] | |||
|
|
15:04 94.31.91.145 talk posted a new comment on X1011 (test) | ||||
|
|
12:36 58.88.94.85 talk posted a new comment on X652 (Why CM4 does not recognize SD card ? Says "SD: card not detected ?") | ||||
19 October 2024
|
|
13:34 | (Comments log)[85.233.54.182; 107.181.178.67; 78.90.162.24 (2×)] | |||
|
|
13:34 107.181.178.67 talk posted a new comment on NASPi Gemini 2.5 (OMV 7 no longer allows USB devices in their software raid. This is intentional and unfortunately your Gemini bridge boards fall into that category. Your hardware raid works fine for me anyway.) | ||||
|
|
06:35 85.233.54.182 talk posted a new comment on X1001 (Can confirm WD 1 TB SSD PC SN730 works, and boots fine) | ||||
|
|
04:49 78.90.162.24 talk posted a new comment on X1011 (Sorry but I can't find way editing my comment. It is Markdown formatted but it is looking ugly as comment section seems not interpret it well.) | ||||
|
|
04:46 78.90.162.24 talk posted a new comment on X1011 (In case someone battling making NAS with large NVMEs... I'm almost 100% sure that 1A@5V(5.00W) is not enough for powering them. Example below is from 4x(Shenzhen Longsys Electronics Co., Ltd. Lexar NM790 NVME SSD (DRAM-less) (rev 01)). ``` # smartctl -c /dev/nvme0 smartctl 7.4 2023-08-01 r5530 [aarch64-linux-6.11.0-1004-raspi] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Firmware Updates (0x14): 2 S...) | ||||
18 October 2024
|
|
23:54 | (Comments log)[176.109.211.22; 46.138.82.4; 128.2.149.23; Lisa (4×)] | |||
|
|
23:54 128.2.149.23 talk posted a new comment on X-UPS1 (Does this UPS handles and protect against reverse current on its output port? If there is current coming back from the output port, will the board still be able to handle it?) Tags: Mobile web edit, Mobile edit | ||||
|
|
12:33 Lisa talk contribs posted a new comment on X-UPS1 (Sorry we haven't tested it with the motor.) | ||||
|
|
12:31 Lisa talk contribs posted a new comment on X-UPS1 (Yes you can use the 12v output from 2 boards since they are wired in parallel.) | ||||
|
|
12:26 Lisa talk contribs posted a new comment on X1202 (Hi,There is a learning process for the IC to read the power level, please try to fully charge and then discharge it a few times and it will remember the process. Please power Pi5 + X1012 poe hat via X1202 UPS.) | ||||
|
|
11:46 Lisa talk contribs posted a new comment on X735 Software (Please refer to X735-script) | ||||
|
|
06:47 176.109.211.22 talk posted a new comment on X735 Software (I get the following error message raspi 4 Okt 18 00:43:11 touscre rc.local[329951]: cat: /sys/class/gpio/gpio5/value: Datei oder Verzeichnis nicht gefunden Okt 18 00:43:11 touscre rc.local[2818]: /etc/x735pwr.sh: Zeile 17: [: =: Einstelliger (unärer) Operator erwartet. Okt 18 00:43:11 touscre rc.local[2818]: /etc/x735pwr.sh: Zeile 21: [: =: Einstelliger (unärer) Operator erwartet. Can you Help ? Greetings Uwe) | ||||
|
|
03:52 46.138.82.4 talk posted a new comment on X1012 (Can X1012 charge X1202 batteries via POE?) | ||||
17 October 2024
| 23:34 | Comments log 46.138.82.4 talk posted a new comment on X1202 ("Capacity: 8.34% (Medium), AC Power State: Unplugged, Voltage: 3.67V Battery level critical." But 3 green LEDs are on) | ||||