Open main menu
Geekworm Wiki

X882

X882 V2.0 Interface Indication
Connection diagram of GPIO connector and OLED screen
How to Power X882 V2.0&Pi4
X882 V2.0 Packing List
X882 V1.3 Packing List
X882 V1.3 Interface Indication
How to Power X882 V1.3&Pi4

Contents

Overview

This is an ultra-compact raspberry pi 4 dual 2.5 inch sata hdd/ssd storage board X882, it allows two 2.5" HDD/SSD to working at the same time with your Raspberry Pi 4. The SuperSpeed USB 3.0 port delivers a blistering data transfer rate of up to 5Gbps, letting you transfer a large amount of data in seconds.

X882 is not sold seperately, we have designed a case for X882 and sold it as a set, please refer to NASPi Gemini

Update History: In December 2022, the X882 V1.3 has been updated to X882 V2.0, remove the USB-C port on X882 V1.3, and update DC 5V power in to wide voltage input DC6-18V power in. The new version completely solve the issue of I/O error.

 

Features

FOR USE WITH

Raspberry Pi 4 Model B

Operating System

All Raspberry Pi operating systems

KEY FEATURES
  • Ultra-compact storage solution for Raspberry Pi 4 - Dual 2.5" SATA HDD/SSD Shield
  • UASP supported ONLY, NOT support TRIM
  • Supports dual 2.5 SATA HDDs/SSDs working at the same time
  • Allows booting OS from your HDD/SSD for faster app opens, web serving and file copying
  • Function to power the RPI via XH2.54 only needing a single power supply
  • Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controllers
  • Integrated USB 3.1 Gen 1 Hub Controller
  • USB3.1 Gen1 5Gb/s connectivity offers plug-and-play functionality on your Raspberry Pi 4
  • Specially-made USB3.1 jumper to connect with Raspberry Pi - no additional cables needed
  • Specially-made X882-A1 connector to connect with Raspberry Pi - power Pi4 without additional cables
  • Ultra-compact design allows for ease of use two HDD/SSD with Raspberry Pi 4
  • LED blue indicator（HDD1,HDD2） indicates each drive status
  • Support Auto power on function
  • Support connecting 3pin PWM Fan
  • On board switch with LED light
  • Press button switch to turn on
  • Press button switch and hold for 1~2 seconds to reboot
  • Press button switch and hold for 3 seconds to implement safe shutdown
  • Press button switch and hold for more than 8 seconds to force shutdown
SPECIFICATION
  • Power supply: 5.1Vdc +/-5% , ≥4A(For X882 V1.3 Version)
  • Power supply: 6-18Vdc +/-5% , ≥4A(For X882 V2.0 Version)
  • Ports & Connectors:
  1. DC jack - 5.5x2.1mm　(DC5525 Jack is compatible with DC5521, you can also use the PSU with DC5525 Jack)
  2. Type-C port（Geekworm Type-C 5V 4A 20W power supply is recommended.）
  3. USB socket - USB 3.0 type A
  4. Power connector - 5V Out XH2.54 2-pin
  5. PWM Fan port 3-pin
  6. SATA socket - 7+15P Female
  • PCB Size 160mm x 107mm
Power Supply Requirement
  • Please use high quality power adapter, or the HDD/SSD may cannot be recognized.
  • Since X882 can install two 2.5-inch hard drives, it needs a high-quality power supply to provide enough current.
NOTES
  • Due to installation restrictions, please pay attention to the thickness of 2.5" SSD/HDD.
  • We do not recommend using Samsung hard drives,Please use hard drives of other brands.
  • As with all SSDs, new SSD/HDD must be formatted before use.
  • Older SSD drives with less efficient flash media may not perform as well as newer drives.
  • A microSD card is required for forceing the Raspbian OS to use the HDD/SSD for its "root" partition
  • Additional USB3.0 A Male to A Male cable is required (not supplied)
  • Do not power your Raspberry Pi via the Pi's 40-pin header and Type-C USB socket at the same time.

Raid setup

Matching Metal Case

X882-C1 metal case with 4010 PWM cooling fan, you can refer to NASPi Gemini.

Packing List

  • 1 x X882 Dual 2.5 SATA HDD Shield(V2.0 or V1.3 Version)
  • 1 x X882-A1 Connector
  • 1 x USB Connector
  • 3 x Jumper Link Pitch 2.54mm
  • 4 x TM3 *6mm Screws (to fix 2.5" HDD/SSD)
  • 4 x F/F Spacer M2.5 *20mm
  • 8 x M2.5 * 5mm Screws

User Manual

Software guide, please refer to XScript

Important!!

For better system compatibility & performance, Please format your HDD/SSD to Ext4 file system.

Document

Some Tips

FAQ

Q1. Why did the second HDD is not recognized?

A: You found only one hard drive if you select the RAID0/RAID1 mode.

Please exit the RAID mode and check again after entering the PM mode(clear raid mode).

More details please refer to Set CLEAR RAID mode of How to configure RAID


Q2: What to do if HDD/SSD is not recognized?

A: Please refer to How to View/Partition/Format/Mount HDD/SSD


Add your comment
Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


 

Anonymous user #10

7 months ago
Score 0  

Hello i planned using two Samsung 970 EVO SSDs are thoose not recommended? What were your issues with thoose SSDs?

Thank you in advance!

Permalink | Reply

 

Harry

7 months ago
Score 0  
Need more detail
Permalink
 

Anonymous user #9

8 months ago
Score 0  
Hello, how can I use the power button on the board? Do I have to connect the power to the board? Because it is currently being powered by the Pi4

Permalink | Reply

 

Anonymous user #11

7 months ago
Score 0  
Can't power X882 from pi 4.
Permalink
 

Anonymous user #7

13 months ago
Score 0  
Do you think you will bring out an "Raspberry Pi 5" upgrade kit? Or do I have to buy a new gemini built for Pi5?

Permalink | Reply

 

Walker

13 months ago
Score 0  
Hello, after the Raspberry Pi 5 is released, we will also upgrade the product. Please follow us. If you have good suggestions, we are also willing to listen.
Permalink
 

Anonymous user #6

13 months ago
Score 0  

Hello,

I've got the version 1.3. I tried several settings but always got troubles when i try to upload a large amount of files: the SSD are disconnecting.

When i tried using seafile, this issue corrupted the database and i lost all the data. Now i'm only using Samba and at least the issue only stop the current upload and don't destroy previous data.

My question is: may it be related to the DC 5V power supply? I'm using a 5V10A supply, but maybe something is limited on the board?

How could i solve or circumvent this problem?

Permalink | Reply

 

Anonymous user #6

13 months ago
Score 0  
Some precision: when I said "SSD are disconnecting": the Pi works well, and i got a message on raspbian specifying that the disks unmounted. when I reboot the pi, the drives are mounted back.
Permalink
 

Walker

13 months ago
Score 0  
Hello, the problem you are talking about may be caused by the power supply, because dual hard drives have relatively high power requirements. The initial version 1.3 used a 5V 4A power input. Later we upgraded to version 2.0, which used a 12V 5A power input. Power supply, the current version 2.0 has solved the problem of insufficient power supply (tip: version 1.3 cannot be directly connected to 12V, because it will burn the board)
Permalink
 

Anonymous user #8

13 months ago
Score 0  

Thank you for your answer. You may understand that i'm not really keen to buy another board, and the 1.3 is not usable as it is whith this power input problem.

On the 2.0, there seems to be components around the DC input that may be used to regulate the power from the 6-18V jack to the components requirements.

I may be able to "replicate" this part of the board, but for this what would be the output specifications?

Are the SSD still powered with 5V on within the 2.0 board?
Permalink
 

Walker

13 months ago
Score 0  

1. First of all, x882 v2.0 cannot use 5V input, because dual hard drives usually require relatively large voltages, and 5V will cause insufficient power supply. 2. your mean by ‘replicate’ may not be able to solve this problem. This is more complicated.

We have reported the problem you previously reported to the manufacturer. In addition to the problem you mentioned may be caused by insufficient power supply of the V1.3 version (when transferring large files), there is another possibility that the SSD EMC interference is relatively large, so you You can try using an HDD to see if the problem still exists.
Permalink
 

Anonymous user #8

13 months ago
Score 0  

Yes, I understand that you cannot input 5V on the 2.0 board, that was not my question.

You are basically telling me that after buying a 50$ V1.3 board that is not working as intended (plus a power supply, shipping and taxes), I should either buy new HDDs or a new 2.0 board.

I'm not really thrilled by this idea, and my goal was to know if there was a way to modify the 1.3 board to help solve the issue (I have access to some equipment and could for exemple build a power supply). I understand that this may not be possible, and even that if it is possible it would not be easy nor guaranteed to work.

But the other possibilities for me would be to either buy a 2.0 board (with no guarantee that it would be better) or some HDD (for lower performance, but i could allow that, but again how to be sure that this investment would solve the issue?), or drop the project altogether.
Permalink
 

Walker

12 months ago
Score 0  

Hello, have you tried HDD? The problem you mentioned may also be caused by SSD EMC interference is relatively large, not necessarily caused by the power supply.

By the way, can you provide your order number?
Permalink
 

Anonymous user #8

12 months ago
Score 0  

Hello,

My order was n°TB-22-7566

I didn't try HDDs yet, i need to borrow some to try.
Permalink
 

Walker

12 months ago
Score 0  
Hello, if you still have this problem after testing the HDD, please contact us in time and we will handle it for you and solve the problem.
Permalink
 

Anonymous user #6

11 months ago
Score 0  

Hello, just to keep you updated: I was able to find another product to plug my SSDs in RAID. It works fine.

The disks are really close together, but the box have its own power supply. So I guess my problem was power supply and not FEM.
Permalink
 

Anonymous user #5

17 months ago
Score 0  
Somehow my 1.3 seems to not start anymore when I install the script. Anyone experience this as well/has a solution?

Permalink | Reply

 

Walker

17 months ago
Score 0  
Hello, I probably understand what you mean, may I ask if it cannot be turned on or the system cannot be started?
Permalink
 

Anonymous user #4

17 months ago
Score 0  

Hi... Did anyone try to boot a Pi from SSD / HDD with this x882 board with just ONE drive attached? In this case my Pi do just NOTHING only if i attach a second drive to the board (no matter if there is something saved on the drive or not - just the hardware) the Pi will boot properly.

Can please anyone try this & give a report?

Permalink | Reply

 

Walker

17 months ago
Score 0  
Hello, it can also work if only one driver is installed
Permalink
 

Anonymous user #3

19 months ago
Score 0  
Could you please illustrate, or make a video to show, how to set the jumpers, I looked all over, and have no idea how read the raid mode schema.

Permalink | Reply

 

Walker

19 months ago
Score 0  

Hi, you can refer to this: https://wiki...nterface.jpg

Let me introduce you roughly, RAID mode (PM/RAID 0/RAID 1/SPAN), when choosing one of the RAID modes, you need short or open A/B, you can choose one of the RAID modes, 1 .Short A&B (RAID 0) at the same time, or 2.open A and short B(RAID 1),3.open B and short A(SPAN),4.open A and B(PM) at the same time, hope it can help you, If you still don’t understand, you can send question to our email. Please contact us at support@geekworm.com. We will explain in more detail and solve the problem for you
Permalink
 

Anonymous user #2

28 months ago
Score 0  

Hi - the X882 board has a blue LED for both HDD1 and HDD2. Just above those blue LEDs are smaller red LEDs.

What do those red LEDs indicate: a) when briefly flash b) when constantly on

Thank you!

Permalink | Reply

 

Lisa

28 months ago
Score 0  

Hello,

It means HDD ERROR, HDD feedback SMART information is wrong, but if your HDD can work normally, you can ignore it.
Permalink
 

Anonymous user #1

30 months ago
Score 0  
ETA for case X882-C1?

Permalink | Reply

 

Abby

30 months ago
Score 0  

Hi,

X882 board is not sold seperately, we sell it as a kit, which include X882 and a case and a PWM fan, pls refer to NASPi Gemini
Permalink
 

Anonymous user #1

30 months ago
Score 0  
X835 compatible?

Permalink | Reply

 

Lisa

30 months ago
Score 0  

Hi，

No compatible X835；metal case please refer toNASPi Gemini
Permalink
Retrieved from "https://wiki.geekworm.com/index.php?title=X882&oldid=19926"