Difference between revisions of "X882"
Jump to navigation
Jump to search
Line 61: | Line 61: | ||
|} | |} | ||
− | == | + | == Raid setup== |
− | + | 【RAID setup and Jumper setting】 | |
− | + | *'''Warning''' : Please backup your data before setup and switch, otherwise you maybe lost your data. | |
− | + | 1. Install the HDDs | |
+ | |||
+ | 2. Please connect the X880 to your PC or Raspberry Pi board and keep power on | ||
+ | |||
+ | 3. Switch RAID mode | ||
+ | * Set the switch button to your preferred RAID mode(PM/RAID 0/RAID 1/SPAN) as per the RAID illustration table. | ||
+ | * Press the '''SET''' button for about 5 seconds, and release it till the blue LED indicators starts flashing. | ||
+ | * After RAID mode changed, please confirm that the PC can recognize the disk(s) properly and shows the right capacity. | ||
+ | |||
+ | or you can run the fdisk -l command to view the hard drive on raspberry pi OS when you connect x880 to raspberry pi board: | ||
+ | fdisk -l | ||
+ | You can found two hard drives if you select 'clear raid mode'(this is PM model) | ||
+ | |||
+ | or | ||
+ | |||
+ | You found only one hard drive if you select the RAID0/RAID1 model | ||
+ | |||
+ | 4. Set CLEAR RAID mode (PM, factory default setup) | ||
+ | * Press the SET button for about 5 seconds then and release it till blue LED indicators starts flashing. | ||
+ | * After above processes, the setup for CLEAR RAID is done. | ||
==Packing List== | ==Packing List== |
Revision as of 16:32, 31 March 2022
Overview
Features
FOR USE WITH |
Raspberry Pi 4 Model B |
Operating System |
All Raspberry Pi operating systems |
KEY FEATURES |
|
SPECIFICATION |
|
Power Supply Requirement |
|
NOTES |
|
Raid setup
【RAID setup and Jumper setting】
*Warning : Please backup your data before setup and switch, otherwise you maybe lost your data.
1. Install the HDDs
2. Please connect the X880 to your PC or Raspberry Pi board and keep power on
3. Switch RAID mode
- Set the switch button to your preferred RAID mode(PM/RAID 0/RAID 1/SPAN) as per the RAID illustration table.
- Press the SET button for about 5 seconds, and release it till the blue LED indicators starts flashing.
- After RAID mode changed, please confirm that the PC can recognize the disk(s) properly and shows the right capacity.
or you can run the fdisk -l command to view the hard drive on raspberry pi OS when you connect x880 to raspberry pi board:
fdisk -l
You can found two hard drives if you select 'clear raid mode'(this is PM model)
or
You found only one hard drive if you select the RAID0/RAID1 model
4. Set CLEAR RAID mode (PM, factory default setup)
- Press the SET button for about 5 seconds then and release it till blue LED indicators starts flashing.
- After above processes, the setup for CLEAR RAID is done.
Packing List
- 1 x X882 V1.3 Dual 2.5 SATA HDD Shield
- 1 x X882-A1 Connector
- 1 x USB Connector
- 3 x Jumper Link Pitch 2.54mm
- 4 x M2.5 *20mm Spacers
- 4 x TM3 *6mm Screws
- 8 x M2.5 *5mm Screws
Enable comment auto-refresher
Anonymous user #10
Permalink |
Harry
Anonymous user #9
Permalink |
Anonymous user #11
Anonymous user #7
Permalink |
Walker
Anonymous user #6
Permalink |
Anonymous user #6
Walker
Anonymous user #8
Walker
Anonymous user #8
Walker
Anonymous user #8
Walker
Anonymous user #6
Anonymous user #5
Permalink |
Walker
Anonymous user #4
Permalink |
Walker
Anonymous user #3
Permalink |
Walker
Anonymous user #2
Permalink |
Lisa
Anonymous user #1
Permalink |
Abby
Anonymous user #1
Permalink |
Lisa