Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
14 May 2024
| 03:16 | Comments log 75.25.130.237 talk posted a new comment on C790 (This is not plug-and-play. Such an app would be welcomed.) | ||||
13 May 2024
|
|
16:21 | (Comments log)[112.220.71.122; 104.28.42.26] | |||
|
|
16:21 104.28.42.26 talk posted a new comment on XScript (I have the same problem...) | ||||
|
|
12:47 112.220.71.122 talk posted a new comment on X1001 (My raspberry PI 5 server has - raspberry PI 5 4 GB - 25W power supply ( 5V 5A ) - Geekworm X1001 PICe HAT - SD Card 64GB - OS: Bookworm 64Bit My PI5 system halts within 3-4 hours from system boot. I tried to mount the SSD (1GB, Samsung Electronics) and booted from SSD successfully without SDCard. But with or without SSD, the system halts after 3~4 hours. When I disconnected X1001 HAT and the PI board( plug off the PICe ribbon cable from X1001 HAT), the system does not freeze for severa...) | ||||
12 May 2024
|
|
15:02 | (Comments log)[202.128.121.113; 193.56.104.165] | |||
|
|
15:02 193.56.104.165 talk posted a new comment on X1007 (When will the housing be available) | ||||
|
|
13:31 202.128.121.113 talk posted a new comment on PiKVM-A3 (Hi. Very interested in buying this. Is there a max resolution or is it purely limited by what the Pi can handle?) | ||||
11 May 2024
|
|
22:44 | (Comments log)[201.202.13.34; 85.60.35.153 (2×)] | |||
|
|
22:44 201.202.13.34 talk posted a new comment on Raspi UPS HAT Board (is there a way to connect i2c ports to a attiny85) | ||||
|
|
05:43 85.60.35.153 talk posted a new comment on X1003 (I followed all the guides and there is no way to get it recognized by my rpi. Also the FPC is correctly connected. How is supposed that the FPC can be broken? and for me does not make sense to buy a new FPC) | ||||
|
|
05:37 85.60.35.153 talk posted a new comment on X1002 (Can you use the x1002 with the neo case 5 for rpi5?) | ||||
10 May 2024
|
|
18:48 | (Comments log)[88.65.197.51; 85.60.35.153; 172.114.135.75] | |||
|
|
18:48 88.65.197.51 talk posted a new comment on X1007 (The packing list image is actually listing four M2.5x10mm scrws. But these are M3?) | ||||
|
|
14:37 172.114.135.75 talk posted a new comment on X1202 (I noticed that the x1202 always said "AC Power OK" even with power plug disconnected. As the pld.py code ran I could press down on the Pi board and the x1202 would say "AC Power Loss". When I let up it would go back to "AC Power OK". Seems like a pogo is not making good contact. Any suggestions?) | ||||
|
|
00:02 85.60.35.153 talk posted a new comment on X1003 (I tried with integral m2 NVMe gen3 x4 2230 and it does not work, but I do not know why. When the x1003 has the m2 connected no led is turned on. Only after I connect the PSU it blink a led from the m2 (not the x1003). If I disconnect the m2 and connect the PSU I can see 2 blue leds of the board. Then what is happening here? no led from the board means no power? I can't get the m2 recognized in the rpi5. Is the board fault? is the ssd? I need help with this.) | ||||
9 May 2024
|
|
20:38 | (Comments log)[95.73.54.49; 88.98.197.180] | |||
|
|
20:38 88.98.197.180 talk posted a new comment on P580 (Thanks. Found a thread on Reddit, a user managed to fit POE HAT with GPIO pins clipped.) | ||||
|
|
15:59 95.73.54.49 talk posted a new comment on How to Configure RAID Setting (Hi, How can I check health of the each disk in hardware RAID mode?) | ||||
7 May 2024
|
|
21:47 | (Comments log)[84.50.46.206; 23.114.212.80 (2×); 1.64.154.121 (2×)] | |||
|
|
21:47 1.64.154.121 talk posted a new comment on XScript (I also using raspberryOS 64bit(bookworm)) | ||||
|
|
21:45 1.64.154.121 talk posted a new comment on XScript (Hi, I followed this guide and now xoff works, but the fan not move at all. It show active and enabled when I enter "sudo systemctl status x-c1-fan.service". Is it the fan broken or have any suggestion to debug?) | ||||
|
|
09:07 23.114.212.80 talk posted a new comment on X1202 (One of the pogos looks like it contacts the area for the Real-time battery. Does this also supply power for that port?) | ||||
|
|
09:06 23.114.212.80 talk posted a new comment on X1202 (What are the specs on the momentary switch port? Does this work like one on the board?) | ||||
|
|
07:50 84.50.46.206 talk posted a new comment on X735-script (I decided to run Home Assistant OS as a virtual machine using Incus so I could use the X735 following the instructions on this wiki page. Fan now is quiet and PWM is doing its thing. I followed the steps here, but I used <code> pip3 install --break-system-packages rpi-lgpio </code> for installinh the GPIO library. To check if the services are working I used <code> systemctl status x735-fan </code> and <code> systemctl status x735-pwr </code> For troubleshooting it helps to check...) | ||||