Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

15:57, 17 January 2025 194.88.96.84 talk performed unknown action "comments/add" on X728 (Having followed your advice in reply to #73, the battery capacity. Only goes up to 80% and then once it reaches this it begins to drop! I also have an X1202 and the same batteries but this goes up to 100% and takes 10-12 hours to discharge. The x728 with the same batteries is taking only 1-2 hours from 80% (max it seems to go to) to discharge to 0.) Tags: Mobile edit Mobile web edit
03:32, 17 January 2025 81.56.119.189 talk performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (The documents are useless are they are generic about the chips and there is no schematic for this specific board model. Anyways if anybody needs, the only way is via voltage divider to ADC pin (GPIO32 to 39) using two 100K Ohm resistors... the voltage can be calculated using the formula: (readAnalog(pin) / 4095) * 3.3 * 2 (also adding a fixed value to calibrate the result is suggested, based on measurements with multimeter))
19:26, 16 January 2025 31.173.21.207 talk performed unknown action "comments/add" on KVM-A3 (do you resolve issue ? i have the same..)
15:21, 14 January 2025 Harry talk contribs performed unknown action "comments/add" on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: <pre>pip install PyQt5</pre> '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: <pre>pip show PyQt5</pre> This command will display the installation details of PyQt5, inclu...)
15:20, 14 January 2025 Harry talk contribs performed unknown action "comments/delete" on X1201
15:20, 14 January 2025 Harry talk contribs performed unknown action "comments/add" on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: pip install PyQt5 '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: pip show PyQt5 This command will display the installation details of PyQt5, including the path where it...)
15:20, 14 January 2025 Harry talk contribs performed unknown action "comments/delete" on X1201
15:20, 14 January 2025 Harry talk contribs performed unknown action "comments/add" on X1201 (This error occurs when Python cannot find the PyQt5 module. It usually happens if PyQt5 is not installed or if the Python interpreter is not correctly configured. '''Solution''' '''1. Install PyQt5''' Ensure that PyQt5 is installed using pip. Open your terminal or command prompt and run: pip install PyQt5 '''2. Verify Installation''' Check if PyQt5 is installed correctly by running: pip show PyQt5 This command will display the installation details of PyQt5, including the path where it i...)
15:13, 14 January 2025 Harry talk contribs performed unknown action "comments/add" on NASPi Gemini 2.5 (Weird question. The fan script has nothing to do with whether the SSD is recognized. What OS are you using?)
12:13, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1200 (please refer to：[https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software])
12:08, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi,There is a learning process for the IC to read the power level, please try to fully charge and then discharge it a few times and it will remember the process.)
12:02, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on NVMe SSD boot with the Raspberry Pi 5 (Hi,please contact us by email <support@geekworm.com> and please note your order ID,thank you.)
12:00, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X306 (Don't support that. Only one 18650 battery can be installed.)
11:59, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X306 (4pin header：solder it yourself if needed. 1. Shorting AL and ON will automatically power on 2. GND and PSW are pins for external reset/momentary switch)
11:46, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X-UPS1 (Please refer to X-UPS1#PCB Dimension above)
11:40, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on X820 (Hi,please contact us by email <support@geekworm.com> and please note your order ID,thank you.)
11:35, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.[https://www.espressif.com/en/support/download/documents Official documents])
11:34, 14 January 2025 Lisa talk contribs performed unknown action "comments/delete" on WEMOS ESP32 Board with 18650 Battery Holder
11:34, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.Official documents https://www.espressif.com/en/support/documents/technical-documents)
11:32, 14 January 2025 Lisa talk contribs performed unknown action "comments/delete" on WEMOS ESP32 Board with 18650 Battery Holder
11:31, 14 January 2025 Lisa talk contribs performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (Hello,We no longer sell this product and this page will no longer be maintained. you can get support on the official website.https://www.espressif.com/en/support/documents/technical-documents)
18:12, 13 January 2025 80.11.191.233 talk performed unknown action "comments/add" on CSI Manual on Pi 5 (Issue solved. On Raspberry Pi 5 with Media controller API 6.6.62, the C779 MIPI CSI-2-TX must be connected on the CAM/DISP 1 port as specified from the device tree. Afterwards, a proper EDID file must be loaded on the properly created subdev to be visible by the HDMI-TX source. Example: v4l2-ctl -d /dev/v4l-subdev2 --set-edid=file=edid.txt --fix-edid-checksums)
13:49, 13 January 2025 73.70.118.131 talk performed unknown action "comments/add" on X306 (Turn off with external button? Pins 3&4 per specs. Short press does switch on, long press does not switch off. Is there any changes that need to be made?)
01:47, 13 January 2025 194.88.96.79 talk performed unknown action "comments/add" on X728 (Can you help me understand why brand new batteries (Panasonic 3400mah) 18650 (4 of them, 2 in the extra battery pack with the case) are showing no more than 90% capacity. The same batteries in the x1202 case with a Raspberry pi5 are showing 99/100% capacity. They share the same source of power which has well in excess of what’s needed. Just wondering if there’s a calibration needed or some other settings to get the number correct.) Tags: Mobile edit Mobile web edit
17:45, 12 January 2025 73.70.118.131 talk performed unknown action "comments/add" on X306 (Can a 2nd 18650 battery be added in parallel for longer run time?)
10:57, 12 January 2025 180.129.86.113 talk performed unknown action "comments/add" on NVMe SSD boot with the Raspberry Pi 5 (I still cannot get my WD Blue SN580 to get working. I followed all steps. - Installed bookworm raspbian on SD card (system boots) - enable PCIe in /boot/firmware/config.txt via adding dtparam=pciex1_gen=3 - eeprom is updated to the latest 2024 Nov version Nothing was working up to this point. Then I edited the eeprom settings via ``` sudo rpi-eeprom-config --edit ``` and added PCIE_PROBE=1. Still nothing is working, i don't see anything in `dmesg` output or in `lspci`. However, both LEDs on...)
09:43, 12 January 2025 186.77.199.44 talk performed unknown action "comments/add" on X1200 (Greetings, I have purchased X1200 and I would like to know how I can monitor the battery voltage from the rasbia os system itself.)
03:54, 12 January 2025 109.245.196.202 talk performed unknown action "comments/add" on X-UPS1 (Hello, where can I find the dimensions specified in millimeters?)
02:01, 12 January 2025 93.170.44.59 talk performed unknown action "comments/add" on X820 (There was an accident with the X820. The IVR P307H chip burned out. It is located next to the auto on/off jumpers. Please tell me what kind of chip it is and how to replace it.)
09:00, 11 January 2025 81.56.119.189 talk performed unknown action "comments/add" on WEMOS ESP32 Board with 18650 Battery Holder (It seems that in this model there is a battery charging system for the integrated battery but no ADC pin are connected to measure the charge... how is it possible? Any way to get battery level through an analogread() of GPIO pin?)
03:12, 11 January 2025 75.28.21.198 talk performed unknown action "comments/add" on 2.8 inch Touch Screen for Pi zero (For Raspbian Bookworm (the most recent) you should be able to just add the following to your config.txt: dtoverlay=vc4-kms-dpi-panel,mzp280,rotate=270 dtoverlay=spi0-0cs dtoverlay=ads7846,penirq=27,xmin=200,xmax=3850,ymin=200,ymax=3850 The first dtoverlay to add vc4-kms-dpi-panel is required to bring up the display itself and requires us to also enable vc4-kms-v3d (which I think is the default now anyway). The second dtoverlay allows us to use the SPI bus without a CS pin (which is taken cu...)
01:38, 11 January 2025 80.11.191.233 talk performed unknown action "comments/add" on CSI Manual on Pi 5 (I'm trying to connect the HDMI-RX end to a Linux (Ubuntu 20.04) PC HDMI port. However, the media-ctl from the media on the Rpi5 shows the message "Failed to open subdev device node". Therefore, no subdevice is found in the /dev/ directory. Is this an issue from the HDMI-TX source?)
00:16, 11 January 2025 109.182.59.94 talk performed unknown action "comments/add" on NASPi Gemini 2.5 (For storage, I use a Gemini 2.5 with 2 SATA SSDs with a capacity of 2TB. For the primary operating system, I have a 32 GB USB stick installed on the top USB 3.0 port. I want to use the fan in PWM mode. When I installed XScript for PWM, I lost access to both SSDs. When I uninstalled this script, I saw both SSDs in the system again. I'm only having problems with the x-c1-fan service, the x-c1-pwr service doesn't affect access to SSDs. Do you have any idea what I can do to re-enable the PWM...)
15:45, 10 January 2025 79.235.200.125 talk performed unknown action "comments/add" on X1201 (Hello, get an error message about the X120X UPS status: chris@MySmartHome:~/x120x $ sudo python3 qtx120x.py Traceback (most recent call last): File "/home/chris/x120x/qtx120x.py", line 17, in <module> from PyQt5.QtWidgets import QApplication, QLabel, QVBoxLayout, QWidget ModuleNotFoundError: No module named 'PyQt5' chris@MySmartHome:~/x120x $ bat.py and merged.py run smoothly Is there a shutdown command like x728off in the X728-UPS?)
14:28, 10 January 2025 Lisa talk contribs performed unknown action "comments/add" on N311 (maybe you can use M2.5 x 10+6 or 11+6mm spacers to mount [Raspberry Pi 5 M.2 HAT])
14:06, 10 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1005 (X1005 is compatible with Hailo-8 AI Accelerator Key B&M.)
11:49, 10 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1202 (X1202 not support OrangePi 5 Max. please refer to X-UPS1)
05:14, 10 January 2025 177.19.217.247 talk performed unknown action "comments/add" on X1202 (Can I use this UPS on the OrangePi 5 Max?)
21:21, 9 January 2025 82.218.207.17 talk performed unknown action "comments/add" on N311 (That is actually the thing I want to do, I want to mount hat+ (original raspberry one) how do i do that if M2,5x4+4 does not fit the top cover?)
01:56, 9 January 2025 81.217.84.209 talk performed unknown action "comments/add" on X1005 (Dear Customer Support supports the geekworm x1005 the "b+m key" hailo-8 ai accelerator from the kit.)
23:53, 8 January 2025 86.87.123.160 talk performed unknown action "comments/add" on X1202 (To disable the auto-on / auto-power-on function, a resistor needs to be removed. The resistor shown for the X1202 (and probably for the x1201 too) is wrong. Removing the indicated resistor, you loose the ability to check for the power adapter being plugged in. The correct resistor is the one near the battery management controller (as shown for the X1200 , but I'm not sure).)
11:03, 8 January 2025 Lisa talk contribs performed unknown action "comments/add" on X1300 Software (Hi,X1300 is a board developed specifically for Raspberry Pi 5;If you have any questions, please leave a message here or you can also contact us by email.)
03:58, 8 January 2025 46.212.53.209 talk performed unknown action "comments/add" on X1300 Software (Has anyone gotten this to work on the raspberry pi 5?)
17:14, 7 January 2025 Abby talk contribs uploaded a new version of File:X1202-V1.1-IMG-7247-Interface-NEW.jpg
16:59, 7 January 2025 Abby talk contribs created page File:X1206-IMG-9057-packing-list.jpg
16:59, 7 January 2025 Abby talk contribs uploaded File:X1206-IMG-9057-packing-list.jpg
16:59, 7 January 2025 Abby talk contribs created page File:X1206-V1.1-Overview.jpg
16:59, 7 January 2025 Abby talk contribs uploaded File:X1206-V1.1-Overview.jpg
16:59, 7 January 2025 Abby talk contribs created page File:X1206-IMG-6837-How-to-Power.jpg
16:59, 7 January 2025 Abby talk contribs uploaded File:X1206-IMG-6837-How-to-Power.jpg