Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
3 October 2024
|
18:23 | (Comments log)[213.249.56.36; 198.44.128.154; 14.153.79.53] | |||
|
18:23 14.153.79.53 talk posted a new comment on X1202 (One more thing you need to consider is to think about the conversion rate of UPS HAT, which is usually around 85%.) | ||||
|
16:37 213.249.56.36 talk posted a new comment on NESPi Pro (What type of battery is needed?) | ||||
|
03:43 198.44.128.154 talk posted a new comment on X1203 (Are two 3.7V batteries required to power the full 5A output?) |
2 October 2024
|
18:41 | (Comments log)[73.171.253.198; 218.253.67.126; 143.93.117.10] | |||
|
18:41 143.93.117.10 talk posted a new comment on X1001 (We have tested two SSDs with the X1002. One works (Intenso M.2 SSD Premium) one does not (Kensington NV2 PCIe 4.0). Both are 256GB models.) | ||||
|
16:43 218.253.67.126 talk posted a new comment on X1012 (Hi, can I use Kioxia SD10 SSD with this?) | ||||
|
05:47 73.171.253.198 talk posted a new comment on 2.8 inch Touch Screen for Pi zero (For those looking for info on the mzp280v00br with the pi zero w: Use the legacy pi os install through the Raspberry P Imager. Enable the legacy Gl driver in raspi-config. I used the 32 bit os as I was on the pi zero. This is the only os that worked. Have fun!) |
1 October 2024
03:01 | Comments log 86.87.123.160 talk posted a new comment on X1202 (Hello, I have 4 batteries, each with a capacity of 2980mAh. The total capacity is therefore 4x2980mAh=11920mAh. With the Raspberry running my application I measured it draws 700mA. So 11920mAh / 700mA = approx 17 hours of running time. Can someone confirm this? Thanks in advance.) |
30 September 2024
|
22:44 | (Comments log)[185.50.233.235 (2×)] | |||
|
22:44 185.50.233.235 talk posted a new comment on X1202 (Actually I see it in the interface picture, point 6: 5VO power output LED: if the Pi 5 is not detected, will turn on for 3 second then off. Does it mean then that the output USB gives continuous power for 3 seconds after the RPI shuts down? Is the powering of the USB output seamless till switch off?) | ||||
|
22:32 185.50.233.235 talk posted a new comment on X1202 (Hi! Could I use the USB output to power up a USB hub? In the interface picture it says: 5V, current unlimited, but down in the user manual it says: USB2.0 type-A power output socket, which implies 5V 500mA, which would be not enough I guess. The use case is that the RPI cuts the power on its usb 3.0 ports at shutdown too soon, causing an increase of the Unexpected Power Loss SMART counter. Using an active USB hub between the RPI and the USB SSD enclosure solves the problem, but at power los...) |
29 September 2024
|
21:42 | (Comments log)[189.183.138.207; 143.244.44.174; 136.144.19.219] | |||
|
21:42 143.244.44.174 talk posted a new comment on X652 (What are all the benefits/use cases of the NVMe? I can store more images and boot from NVMe, but can I screen capture to the NVMe from PiKVM? Anything else?) Tags: Mobile web edit, Mobile edit | ||||
|
03:29 189.183.138.207 talk posted a new comment on X1100 (Is it possible to connect 2 x SATA SSD 2.5"?) | ||||
|
02:14 136.144.19.219 talk posted a new comment on NVMe SSD boot with the Raspberry Pi 5 (I can confirm that it is possible to boot Home Assistant from NMVw using Geekworm X1001 PCIe to M.2 HAT and Kingston NV2 1TB M.2 2280 NVMe. After putting it all together the device did not even boot Pi Lite. (did not have monitor to get debug) Then after removing the SSD it did boot. And after updating boot loader and setting dtparam=pciex1_gen=3 I was able to boot with the SSD attached. From there I flashed the SSD with Home Assistant through terminal directly on device and then booted from...) |
28 September 2024
00:24 | Comments log 107.192.62.177 talk posted a new comment on X1203 (With the 6-20V input on the DC jack, is it safe to operate this directly from vehicle/car power or do you recommend using an external regulator in between? Thanks!) |
27 September 2024
|
22:51 | (Comments log)[222.235.157.71; 151.68.107.153; 134.61.130.68] | |||
|
22:51 222.235.157.71 talk posted a new comment on X1300 Software (At step 3, when I connect to CSI 1 (as per the hardware installation guide), it is displayed as a picture. However, when I connect to CSI 0, it is not recognized—only /dev/media0 appears in rpi-cfe. Is this normal?) | ||||
|
22:46 134.61.130.68 talk posted a new comment on X1100 (The X1100 looks really well designed. Especially a great combination with the X1100-C1 Metal Case. It would be interesting to know whether the USB-SATA chip that is used supports the SSD function: TRIM (or UNMAP in SCSI terminology). According to the description, it is an unspecified “USB 3.1 Gen1 to SATA 6Gb/s bridge controller”, so it can at least be assumed that the controller supports the UAS (USB Attached SCSI) protocol.) | ||||
|
06:04 151.68.107.153 talk posted a new comment on X1012 (I would like to use both the PoE and AUX power simultaneously, so that if one of them fails, the other one keeps the system running. Unfortunately, currently, if I disconnect the AUX power, the Raspberry Pi shuts down and then restarts powered by PoE. How should I proceed to achieve the desired result?) |