Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
27 June 2024
|
|
12:30 | (Comments log)[182.230.201.111 (2×); 175.116.49.141 (2×)] | |||
|
|
12:30 182.230.201.111 talk posted a new comment on X1002 (I used hailo-8 not hailo-8L) | ||||
|
|
12:29 182.230.201.111 talk posted a new comment on X1002 (When I was using the hailo-8 chip and x1002, the board didn't turn on because of physical contact between the board and chip. I can see turn on properly when I'm not joining the bolt and just stick in it. If you're thinking of using the hailo-8, I'd better look into other boards. I used hailingo-8 not hailo-8L) | ||||
|
|
09:28 175.116.49.141 talk posted a new comment on X1202 (Can this be used with the X708-A1 board?) | ||||
|
|
08:58 175.116.49.141 talk posted a new comment on X708-A1 (Can this be used with the X1202 board?) | ||||
26 June 2024
| 04:16 | Comments log 89.176.154.85 talk posted a new comment on X728 (After power loss the batteries were fully discharged. After that power was restored and now LEDs 5V OUT and AC FAIL are blinking. What does it mean?) | ||||
25 June 2024
| 16:58 | Comments log 125.164.16.25 talk posted a new comment on X1002 (Hi again, I'd like to ask something about WLAN connection. When I use SD card to boot, it connects to WLAN just fine. But, when I attached X1002 in, with or without SSD, with or without P580, it doesn't want to connect to my WLAN. What's wrong here? Tested before and after applying electrical tape properly (Yes the question below is mine. All holes are intact, no shorts happened between the flex cable and the case)) | ||||
23 June 2024
|
|
23:34 | (Comments log)[93.44.51.122; 185.71.88.123] | |||
|
|
23:34 93.44.51.122 talk posted a new comment on X1200 (I'm using the RTC wakeup to schedule the power on my rpi5, along with POWER_OFF_ON_HALT=1 to save energy when powered off. According to the documentation the x1200 will cut off the power if the rpi5 is powered off. Is there a way to disable this feature and let the x1200 output power even if the rpi5 is shutdown? Or is there an alternative way to use the RTC wakeup when the rpi5 is connected to the X1200?) | ||||
|
|
00:24 185.71.88.123 talk posted a new comment on N508 (I would suggest not moving the holes, but make this side part of the base and the opposite side part of the lid.) | ||||
22 June 2024
|
|
23:22 | (Comments log)[71.246.207.26; 185.71.88.123] | |||
|
|
23:22 71.246.207.26 talk posted a new comment on LVDS2 (Has anyone used this or another product on a Tesla's round 4+2 pin LVDS connector at the screen or MCU? This board shows more pins.) | ||||
|
|
20:38 185.71.88.123 talk posted a new comment on N508 (Another big problem of the case is that the antenna holes are not in the base, but on the lid. The antenna cords cannot be easily detached and they are short and fragile. It makes it difficult to disassemble the case and keep it with the detached lid. Would be nice to see the holes on the other side in the next version of the case.) | ||||