X1300

X1300

X1300

X1300

X1300

Overview

The X1300 HDMI to CSI-2 bridge with I2S audio interface has been specifically designed for the Raspberry Pi 5. It features the Toshiba TC358743XBG bridge chip, supporting HDMI input up to 1080P at a refresh rate of 60 fps.

PS:

If you need the same kind of product used on the Raspberry Pi 4, please refer to the X630

---

Geekworm HDMI to CSI Module Series:

Convert HDMI signal acquisition into CSI signal and I2S audio signal. The maximum capture resolution depends on the HDMI to CSI converter board as well as the Raspberry Pi hardware.

Raspberry Pi hardware are primarily divided into two series, one supporting a maximum of 1080P60Hz and the other supporting a maximum of 1080P50Hz.

• Raspberry Pi versions that support up to 1080P60Hz: CM3, CM4, Pi 5B
• Raspberry Pi versions that support up to 1080P50Hz: zero, zero2, Pi3B, Pi4B, etc.

Picture	Model	Description	Max Input Resolution	I2S Audio	HDMI Capture Chip	PCB Dimension	CSI-2 Connector	Supported SOC
	C779	HDMI to CSI-2	1080p50fps	NO	Toshiba TC358743XBG	35 x 50 mm	15-PIN FPC (pitch 1.0 mm)	Pi 5B / 4B / 3B+ / 3B / 3A+ / Zero / Zero W/ Zero 2W
	C790	HDMI to CSI-2	1080p60fps	Yes	Toshiba TC358743XBG	30 x 45 mm	15-PIN FPC (pitch 1.0 mm) on the front of C790; 22-PIN FPC (pitch 0.5 mm) on the rear of C790	Pi 5B / 4B / 3B+ / 3B / 3A+ / Zero / Zero W/ Zero 2W / CM3 / CM4
	X630	HDMI to CSI-2	1080p50fps	Yes, but I2S wiring or the X1300-A2 accessory board is necessary	Toshiba TC358743XBG	30 x 42.4 mm	15-PIN FPC (pitch 1.0 mm)	4B / 3B+ / 3B / 3A+ / Zero W / Zero 2W
	X1300	HDMI RX to MIPI CSI-2-TX	1080p60fps	Yes, but I2S wiring or the X1300-A2 accessory board is necessary	Toshiba TC358743XBG	30 x 37.5 mm	22-PIN FPC (pitch 0.5 mm)	Pi 5B / CM4 IO
	X1301	HDMI RX to MIPI CSI-2-TX HDMI loop output	1080p60fps	Yes	Toshiba TC358743XBG	57 x 85.5 mm	22-PIN FPC (pitch 0.5 mm)	Pi 5B / 4B / 3B / 3B+ / 3A+ / CM4 IO
	X1300-A2	I2S audio accessory board for X630 / X1300	1080p60fps	This is a I2S audio accessory board	-	57 x 65 mm	-	work with X1300 HDMI to CSI-2 for Raspberry Pi 5B, CM4 IO board work with X630 HDMI to CSI-2 for Raspberry Pi 4B, 3B+ and 3B

Features

• Compatible With : Raspberry Pi 5B Only (NOT Raspberry Pi 4 and Pi 3) / Raspberry Pi Compute Module 4 IO board
• Capable of handling video formats up to 2K Full HD (1920x1080, 60fps).
• Equipped with the HDMI to CSI-2 bridge chip: Toshiba TC358743XBG
• Supports MIPI CSI-2 with 4 data lanes, each with speeds of up to 1 Gbps per lane
• Enables HDMI audio input and transmission over I²S - (Note: To capture HDMI audio via I2S, additional wiring or the X1300-A2 accessory board is necessary.)
• Prevents HDMI backpowering to the Raspberry Pi CSI
• Features a CSI-2 connector: 22-pin FPC with 0.5mm pitch
• Boasts an ultra-compact design: 30 x 37.5 mm (PCB size)
• Easily mountable on the Raspberry Pi 5, allowing you to customize your perfect case

Applications

Here are some applications of HDMI to CSI (Camera Serial Interface) conversion:

1. Digital Media Adapters: HDMI to CSI adapters allow HDMI cameras to be used just like standard Raspberry Pi CSI cameras. This is useful for digital media adapters that need to process HDMI input.

2. Smart Monitors: Smart monitors can benefit from HDMI to CSI conversion, enabling them to accept HDMI video streams and integrate them into their display systems.

3. Set-Top Boxes (STBs): STBs often require video input from various sources. HDMI to CSI conversion allows STBs to handle HDMI signals efficiently.

4. Smart TVs: Some smart TVs may need to process HDMI input for features like picture-in-picture or video conferencing. HDMI to CSI bridges facilitate this integration.

5. Entertainment Screens: Whether it's for gaming consoles, streaming devices, or other entertainment systems, HDMI to CSI conversion ensures compatibility with HDMI sources.

6. KVM over IP: IP-KVM (Keyboard, Video, Mouse over IP) solutions using a Raspberry Pi, This bridge allows you to capture full HD video with low latency and supports H.264 video encoding of your desktop.

Remember that HDMI to CSI adapters are particularly useful when interfacing HDMI cameras with Raspberry Pi boards. They provide a seamless way to incorporate HDMI video streams into various applications.

Technical Specification

Power supply	3.3Vdc via FFC
Ports & Connectors	HDMI video input connector x1 - Type-A 19-pin MIPI connector x1 - 22pin 0.5mm pitch 10-pin functional connector x1 - 10-pin 1.0pitch
MIPI cable length	30mm
PCB Size	37.5mm x 30mm

User Manual

• Hardware connection instructions: X1300 Hardware
• Software usage instructions: X1300 Software
• Installation Video for X1300+X1300 A2+X1300-C1: https://youtu.be/GOHjzu7Rr1E

Packing List

• 1 x X1300 V1.0 HDMI to CSI-2 module
• 2 x 22-pin MIPI FFC (30mm length)
• 1 x Screw pack

Add your comment

Geekworm Wiki welcomes all comments. If you do not want to be anonymous, register or log in. It is free.

Sort by date Sort by score

Enable comment auto-refresher

You are ignoring the author of this comment

Show comment | Manage ignore list

Anonymous user #1

29 days ago

Score 0

Is there any reason this X1300 set cannot also be used with a rpi4 if I used a 22-pin 0.5 pitch to 15-pin 1.0 pitch FFC cable? I understand that the fewer CSI lanes means 1080p50 rather than 1080p60, but the X1300 and X630 use the same toshiba hdmi chip.

Permalink | Reply

You are ignoring the author of this comment

Show comment | Manage ignore list

Harry

28 days ago

Score 0

You are right. If you replace the FPC, you can also use the X1300 on the RPi4

Permalink