Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
23 August 2024
|
21:42 | (Comments log)[172.103.144.22; 84.157.71.126; 94.138.76.69 (2×)] | |||
|
21:42 84.157.71.126 talk posted a new comment on X-C1 Software (For anyone for whom the install.sh breaks the boot sequence with an infinite loop of error messages (complaining that the file or directory wasn't found for /sys/class/gpio/gpio17/ or something): 1. Go to the install.sh file 2. Replace the first echo block with: ``` echo '#!/bin/bash SHUTDOWN=4 REBOOTPULSEMINIMUM=200 REBOOTPULSEMAXIMUM=600 #echo "$SHUTDOWN" > /sys/class/gpio/export #echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction BOOT=17 #echo "$BOOT" > /sys/class/gpio/export #echo...) | ||||
|
17:15 94.138.76.69 talk posted a new comment on X301 (If you FAT32 format an SD card and put the bootcode.bin file from PiOS on it, you are able to boot from the X301 attached hdd/ssd. There is also an anclosure available to 3D print on the Printables website.) | ||||
|
16:27 94.138.76.69 talk posted a new comment on X301 (The Pi Zero 2 W DOES support boot from USB out of the box. I have tried both a USB thumbdrive and an SSD through a USB SATA adapter on an OTG-to -USB cable. All work fine. But for some reason the X301, which is essentially an OTG adapter, does not allow booting from the HDD/SSD attached. Big disappointment.) | ||||
|
11:51 172.103.144.22 talk posted a new comment on NASPi 3.5 (While using RAID1 if one of the drives were to fail, how could I know?) |
22 August 2024
|
23:57 | (Comments log)[84.179.227.232; 192.77.184.26; 163.116.157.24] | |||
|
23:57 192.77.184.26 talk posted a new comment on X1012 (What does the "EN" solder pad on the group "3V3, EN, GND, 5V" on the underside of the X1012 do? Is that an Enable pin, enabling a remote on/off switch? If the EN pin is connected to GND, in the same group, will that have the same function as pressing the reset button on the RPi 5?) | ||||
|
19:55 163.116.157.24 talk posted a new comment on X708-A1 (What is the output voltage through the PH 2.0?) | ||||
|
18:39 84.179.227.232 talk posted a new comment on X1008 (Is there an option to power this (Rpi, board and 3.5 HDD) via PoE to get rid of an additional power supply?) |
21 August 2024
|
17:14 | (Comments log)[182.191.70.99; 181.41.131.77] | |||
|
17:14 181.41.131.77 talk posted a new comment on X306 (Hi! Is there any way to read the battery percentage (25%,50%,75% and 100%) from the Pi using the onboard pins? Thanks!) | ||||
|
16:18 182.191.70.99 talk posted a new comment on X728-script (Hi. I am suing this device with Orange Pi 5+. But the I2C does not work. Can anyone guide?) |
20 August 2024
23:13 | Comments log 182.52.185.30 talk posted a new comment on X1202 (Thanks, one more question. Does this unit has undervoltage protection (and which voltage)? I don't see this detail on product page.) |