Difference between revisions of "Template:PCIe to NVME Sets"

From Geekworm Wiki
Jump to navigation Jump to search
 
(25 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
<span class="tb_red">Geekworm PCIe to NVME Sets:</span>
 
<span class="tb_red">Geekworm PCIe to NVME Sets:</span>
 +
 +
After the release of the [https://www.raspberrypi.com/products/ai-kit/ Raspberry Pi AI Kit], we tested four PIPs: [[X1001]], [[X1004]], [[X1011]], and [[M901]]. X1001, X1004, and M901 all support the hailo-8 ai ​​accelerator, but X1011 does not.
 +
 +
It should be noted that [[X1004]] uses [https://www.asmedia.com.tw/product/213yQcasx8gNAzS4/b7FyQBCxz2URbzg0 ASMedia ASM1182e] PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch, and speed is still PCIe Gen 2.0 5Gbps speed. when you use an hailo-8 ai accelerator, Raspberry Pi Fundation highly recommends using PCIe 3.0 to achieve  best performance with your AI Kit.
 +
 +
'''Our tentative conclusions are as follows:'''
 +
* If you need to use hailo-8 ai accelerator with high performance, it is recommended to use [[X1015]]/[[X1002]]/[[X1003]]/[[M901]]/ [https://www.raspberrypi.com/products/m2-hat-plus/ the official M.2 HAT+] etc. When choosing these PIP boards, '''you should focus on whether there is a conflict between the camera cable and the PIP board installation''', and enable PCIe3.0 to use hailo-8 ai accelerator. At the same time, you need to prepare an SD card as the system disk.
 +
* If you don't care about the high performance brought by PCIe 3.0, then you can consider using [[X1004]], so that you can use any socket of X1004 to install NVME SSD as the system disk, and another socket to install hailo-8 ai accelerator, so as to have both.
 +
 
{| class="wikitable"
 
{| class="wikitable"
−
! Model !! Compatible with !!  Position!!  NVMe M2 SSD Support!!  Matching Case !! Support NVMe Boot !! Other
+
! Model !! Compatible with !!  Position!!  NVMe M2 SSD Length Support!!  Matching Case !! Matching Cooler !! Support NVMe Boot !! Support PCIe 3.0 !! Support Hailo-8 AI Accelerator
 
|-
 
|-
−
| [[X1000]] || Raspberry Pi 5 || Top|| 2230/2242 NVMe M2 SSD|| [[P579]]||Yes||
+
| [[X1000]] || Raspberry Pi 5 || Top|| 2230/2242|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||Not tested
 
|-
 
|-
−
| [[X1001]] || Raspberry Pi 5 ||Top|| 2230/2242/2260/2280 NVMe M2 SSD|| [[P579]]||Yes||
+
| <mark>[[X1001]]</mark> || Raspberry Pi 5 ||Top|| 2230/2242/2260/2280|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||<span class="tb_red">Yes</span>
 
|-
 
|-
−
| [[X1002]] || Raspberry Pi 5 ||<span class="tb_red">Bottom</span>|| 2230/2242/2260/2280 NVMe M2 SSD|| [[P580]]||Yes||
+
| <mark>[[X1002]]</mark> || Raspberry Pi 5 ||<span class="tb_red">Bottom</span>|| 2230/2242/2260/2280|| [[P580]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||Not tested
 
|-
 
|-
−
| [[X1003]] || Raspberry Pi 5 ||Top || 2230/2242 NVMe M2 SSD|| [[P579]] / [[P425]] / [https://www.raspberrypi.com/products/raspberry-pi-5-case/ Raspberry Pi 5 Official case]||Yes||only can be used with [[H500| Raspberry Pi 5 Official Active Cooler]] or [[H501]]
+
| <mark>[[X1003]]</mark> || Raspberry Pi 5 ||Top || 2230/2242|| [[P579]] / [[P425]] ||[[H500|Official Cooler]] / [[H501]] <span class="tb_red">Only</span>||Yes||-||Not tested
 
|-
 
|-
−
| [[X1004]] || Raspberry Pi 5 ||Top|| <span class="tb_red">Dual 2280</span> NVMe M2 SSD|| [[P579|P579-V2]]||supports NVMe boot with the latest eeprom (2024/05/17 version)||
+
| <mark>[[X1004]]</mark> || Raspberry Pi 5 ||Top|| <span class="tb_red">Dual ssd</span>: 2280|| [[P579|P579-V2]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes (Requires EEPROM 2024/05/17 version and above)||NO||<span class="tb_red">Yes</span>
 
|-
 
|-
−
| [[X1011]] || Raspberry Pi 5 ||<span class="tb_red">Bottom</span>|| <span class="tb_red">4PCS</span> 2230/2242/2260/2280 NVMe M2 SSD|| [https://wiki.geekworm.com/X1011#Matching_Case X1011-C1]||supports NVMe boot with the latest eeprom (2024/05/17 version)||
+
| <mark>[[X1015]]</mark> || Raspberry Pi 5 ||Top|| 2230/2242/2260/2280|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||<span class="tb_red">Yes</span>
 
|-
 
|-
−
| [[M901]] || Raspberry Pi 5 ||Top|| 2230/2242/2260/2280 NVMe M2 SSD|| [[P579]]||Yes||
+
| <mark>[[X1005]]</mark> || Raspberry Pi 5 ||<span class="tb_red">Bottom</span>|| <span class="tb_red">Dual ssd</span>: 2230/2242/2260/2280|| No matching case yet||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes (Requires EEPROM 2024/05/17 version and above)||NO||<span class="tb_red">Yes</span>
 
|-
 
|-
−
| [[Q100]] || Raspberry Pi 5 ||Top|| 2242 NVMe M2 SSD|| [[P579]]||Yes||With 1.3" 240x240 Color TFT
+
| <mark>[[X1011]]</mark> || Raspberry Pi 5 ||<span class="tb_red">Bottom</span>|| <span class="tb_red">4 ssds</span>: 2230/2242/2260/2280|| [[X1011#Matching_Case | X1011-C1]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes (eeprom 2024/05/17 and later VER)||NO||NO
 
|-
 
|-
−
| [[Q200]] || Raspberry Pi 5 ||Top|| <span class="tb_red">Dual 2280</span> NVMe M2 SSD|| [[P579]]||<span class="tb_red">NO</span>||
+
| [[M901]] || Raspberry Pi 5 ||Top|| 2230/2242/2260/2280|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||<span class="tb_red">Yes</span>
 
|-
 
|-
−
| [[M300]] || Raspberry Pi 5 ||Top|| 2230/2242 NVMe M2 SSD|| [[P579]]||Yes||
+
| [[Q100]] || Raspberry Pi 5 ||Top|| 2242|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||Not tested
 
|-
 
|-
−
| [[M400]] || Raspberry Pi 5 ||Top|| 2230/2242/2280 NVMe M2 SSD|| [[P579]]||Yes||
+
| [[Q200]] || Raspberry Pi 5 ||Top|| <span class="tb_red">Dual ssd</span>: 2280|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||<span class="tb_red">NO</span>||-||Not tested
 +
|-
 +
| [[M300]] || Raspberry Pi 5 ||Top|| 2230/2242|| [[P579]]||[[H500|Official Cooler]] / [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||Not tested
 +
|-
 +
| [[M400]] || Raspberry Pi 5 ||Top|| 2230/2242/2280|| [[P579]]||[[H500|Official Cooler]]/ [[Argon THRML 30-AC|Argon THRML Cooler]] / [[H505]]/[[H501]]||Yes||-||Not tested
 
|}
 
|}

Latest revision as of 17:49, 18 June 2024

Geekworm PCIe to NVME Sets:

After the release of the Raspberry Pi AI Kit, we tested four PIPs: X1001, X1004, X1011, and M901. X1001, X1004, and M901 all support the hailo-8 ai ​​accelerator, but X1011 does not.

It should be noted that X1004 uses ASMedia ASM1182e PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch, and speed is still PCIe Gen 2.0 5Gbps speed. when you use an hailo-8 ai accelerator, Raspberry Pi Fundation highly recommends using PCIe 3.0 to achieve best performance with your AI Kit.

Our tentative conclusions are as follows:

  • If you need to use hailo-8 ai accelerator with high performance, it is recommended to use X1015/X1002/X1003/M901/ the official M.2 HAT+ etc. When choosing these PIP boards, you should focus on whether there is a conflict between the camera cable and the PIP board installation, and enable PCIe3.0 to use hailo-8 ai accelerator. At the same time, you need to prepare an SD card as the system disk.
  • If you don't care about the high performance brought by PCIe 3.0, then you can consider using X1004, so that you can use any socket of X1004 to install NVME SSD as the system disk, and another socket to install hailo-8 ai accelerator, so as to have both.
Model Compatible with Position NVMe M2 SSD Length Support Matching Case Matching Cooler Support NVMe Boot Support PCIe 3.0 Support Hailo-8 AI Accelerator
X1000 Raspberry Pi 5 Top 2230/2242 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Not tested
X1001 Raspberry Pi 5 Top 2230/2242/2260/2280 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Yes
X1002 Raspberry Pi 5 Bottom 2230/2242/2260/2280 P580 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Not tested
X1003 Raspberry Pi 5 Top 2230/2242 P579 / P425 Official Cooler / H501 Only Yes - Not tested
X1004 Raspberry Pi 5 Top Dual ssd: 2280 P579-V2 Official Cooler / Argon THRML Cooler / H505/H501 Yes (Requires EEPROM 2024/05/17 version and above) NO Yes
X1015 Raspberry Pi 5 Top 2230/2242/2260/2280 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Yes
X1005 Raspberry Pi 5 Bottom Dual ssd: 2230/2242/2260/2280 No matching case yet Official Cooler / Argon THRML Cooler / H505/H501 Yes (Requires EEPROM 2024/05/17 version and above) NO Yes
X1011 Raspberry Pi 5 Bottom 4 ssds: 2230/2242/2260/2280 X1011-C1 Official Cooler / Argon THRML Cooler / H505/H501 Yes (eeprom 2024/05/17 and later VER) NO NO
M901 Raspberry Pi 5 Top 2230/2242/2260/2280 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Yes
Q100 Raspberry Pi 5 Top 2242 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Not tested
Q200 Raspberry Pi 5 Top Dual ssd: 2280 P579 Official Cooler / Argon THRML Cooler / H505/H501 NO - Not tested
M300 Raspberry Pi 5 Top 2230/2242 P579 Official Cooler / Argon THRML Cooler / H505/H501 Yes - Not tested
M400 Raspberry Pi 5 Top 2230/2242/2280 P579 Official Cooler/ Argon THRML Cooler / H505/H501 Yes - Not tested
Retrieved from "https://wiki.geekworm.com/index.php?title=Template:PCIe_to_NVME_Sets&oldid=20971"