Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
13 May 2024
| 12:47 | Comments log 112.220.71.122 talk posted a new comment on X1001 (My raspberry PI 5 server has - raspberry PI 5 4 GB - 25W power supply ( 5V 5A ) - Geekworm X1001 PICe HAT - SD Card 64GB - OS: Bookworm 64Bit My PI5 system halts within 3-4 hours from system boot. I tried to mount the SSD (1GB, Samsung Electronics) and booted from SSD successfully without SDCard. But with or without SSD, the system halts after 3~4 hours. When I disconnected X1001 HAT and the PI board( plug off the PICe ribbon cable from X1001 HAT), the system does not freeze for severa...) | ||||
28 April 2024
| 14:00 | Comments log 24.128.44.197 talk posted a new comment on X1001 (The XH2.54 5V power connector connects to the GPIO on the Raspberry Pi 5?) | ||||
27 April 2024
| 22:34 | Comments log 180.150.80.69 talk posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (Cheers for creating this excellent, straight-forward article. I wish I had permission to register but apparently I don't, so I'm posting this anon. Thanks!) | ||||
24 April 2024
| 16:57 | Comments log 185.65.135.178 talk posted a new comment on X1001 (Integrated with XH2.54 5V power connector. It is, but what is not supplied or offered is a short cable to connect to the Pi5 board. And yes, my Pi5 is working great with the X1001 and a 1TB 2280 SDD. The dtparam=pciex1_gen=3 has been set and the microSD has been removed. So I don't really need the extra power connector, but it should have been included anyways just to be on the safe side.) | ||||
22 April 2024
|
|
05:33 | (Comments log)[177.99.103.158; 108.76.201.4 (2×)] | |||
|
|
05:33 108.76.201.4 talk posted a new comment on X1001 (I posted as anon user #15 earlier. I think I got the problem resolved by routing the cable a little differently. I noticed I did not have the problem if the device was outside of the case (Geekworm P579-V2-K). I tried adding some electrical tape to the inside of the case (per Q4), but that didn't make a difference. However, I noticed that, when the pi was installed in the case, the FCC cable was being pressed against the inside of case, which caused it to bend some and appeared to cause...) | ||||
|
|
04:04 177.99.103.158 talk posted a new comment on X1001 (Is there a way to disable the LED light, its so annoying.) | ||||
|
|
01:14 108.76.201.4 talk posted a new comment on X1001 (I've installed the X1001 with a 128GB Silicon Power P24A60 (Model A60), and it has booted and ran fine for at least an hour or so, then everything just stops responding and basic commands like sudo and ls are no longer found. It behaves as though the drive has being disconnected, but the blue light is still on when this happens. I have re-seated the FCC cable on both ends a few times. It seems to be seated fully and securely. Also, the drive is typically recognized (at least momentarily)...) | ||||