Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
26 May 2024
|
02:38 | (Comments log)[47.158.215.169 (2×)] | |||
|
02:38 47.158.215.169 talk posted a new comment on X1001 (Sorry scratch that, still seems to fail with heavy disk usage) | ||||
|
00:09 47.158.215.169 talk posted a new comment on X1001 (I can confirm updating the firmware seems to work on the pi5. Have a WD black SN770. Worked with USB, didn't work with the NVMe hat. Originally would boot very slow, and couldn't reliably launch a terminal, or a web browser at all. System would freeze or go to gray screen/black screen. Booted with the drive in a USB enclosure and went to raspi-config and loaded new bootloader/firmware through the advanced options, reinstalled the drive into the hat and now boots fine, fast, and can lau...) |
25 May 2024
09:42 | Comments log 45.134.224.250 talk posted a new comment on X1200 Hardware (What is the low-charging rate? What is the high-charging rate?) |
22 May 2024
06:47 | Comments log 23.93.48.84 talk posted a new comment on X1202 (Will this provide power if only 2 batteries are installed? I don't need the capacity of 4 18650s, but having a place to store and charge spares would be nice.) |
21 May 2024
04:14 | Comments log 23.114.212.80 talk posted a new comment on X1202 (Is there a way to run the pi5 off of the 5v out XH connector? Due to size constraints I cannot use the pogo pins. If I need to solder connectors from the GPIO to the Pogo pins, which ones are necessary for minimal function?) |
17 May 2024
|
05:59 | (Comments log)[216.24.212.246; 216.24.212.210] | |||
|
05:59 216.24.212.210 talk posted a new comment on X1201 (would NOT take a charge) | ||||
|
05:58 216.24.212.246 talk posted a new comment on X1201 (Yes, the batteries were hardly used but one was bad; it would take a charge. Thanks) |
15 May 2024
04:38 | Comments log 172.59.122.138 talk posted a new comment on How to enable OLED display (you say: Hi, you can ignore python-smbus package I ask: How Instructions do not work at all. Many failures.) |
13 May 2024
|
16:21 | (Comments log)[112.220.71.122; 104.28.42.26] | |||
|
16:21 104.28.42.26 talk posted a new comment on XScript (I have the same problem...) | ||||
|
12:47 112.220.71.122 talk posted a new comment on X1001 (My raspberry PI 5 server has - raspberry PI 5 4 GB - 25W power supply ( 5V 5A ) - Geekworm X1001 PICe HAT - SD Card 64GB - OS: Bookworm 64Bit My PI5 system halts within 3-4 hours from system boot. I tried to mount the SSD (1GB, Samsung Electronics) and booted from SSD successfully without SDCard. But with or without SSD, the system halts after 3~4 hours. When I disconnected X1001 HAT and the PI board( plug off the PICe ribbon cable from X1001 HAT), the system does not freeze for severa...) |