Topic fan script:
I had to add
LC_ALL=C in the 3rd line
else I got "/usr/local/bin/x-c1-fan.sh: Zeile 184: printf: 38.46: Ungültige Zahl." all over the system log. Locale was german, and german's number format has a "," instead of "."
Topic RTC:
I added
[pi4]
dtoverlay=i2c6,pins_22_23
dtoverlay=i2c-rtc,ds3231=on,i2c6
to /boot/config.txt and connected the RTC with jumper wires to GPIO 22 and 23 (and 3.3/GND of course). The little RTC-Module found it's place inside the case near the GPIO input header and jumpers. Works fine!
I have successfully upgraded my stock fan to a more silent Noctua one. While out of the case the fan is really quiet and works as expected, when I fit the case and power on the noise is no different to the stock fan.
The NASPi's fan is also a silent fan. We think it is the case that there are not enough ventilation holes, we will increase the fan holes in the next version to improve this problem.
I've bought a Noctua 40x10mm non-PWM fan and it looks like I need to make some cable modifications as the connector block on the Noctua won't fit the onboard connector on my X-C1 v2.0. I have a 3 to 2 pin adapter cable that came with my fan. Can the onboard 5V connector be used to power the new fan instead of having to cut cables?
Everything works well if the naspi top cover is open... the moment I close the case with the 4 screws, wifi stops working and the disk start to throw errors. What can I do?
Which GPIO pins are wired to the 4 pin switch socket on the X-C1 adapter board? I want to connect a 128x64 OLED display for status monitoring and need to get to the SDA and SCL GPIO pins that were used by the 7 pin GPIO board.
Hi,could you please tell us more information? installed scripts, what operating system to use, and it is better to provide some pictures or videos. Please contact us by email and tell us your order number【support@geekworm.com】. thanks
Just purchased: "Geekworm NASPi 2.5 inch SATA HDD/SSD NAS Storage Kit for Raspberry Pi 4 Model B"
But I received a fan with only two wires. It's 5v but because it's only two wires I can't connect it to the 3 pin fan connector. Please advise, thanks :-)
Hi,could you please tell us your order NO.?[support@geekworm.com]; You can use the fan temporarily without installing any scripts.just connect directly
Trying to find out if the Naspi case supports auto-power on so that if the power fails it will apply power so the RPi can restart? Eg if a NAS is implemented I want it to run continuously including after power failures.
Hello,Hello,What system are you using. could you please send some pictures of the operation so that we can find out the problem.【support@geekworm.com】 ;And tell us your order number. Best regards
Is there enough gap between the front panel and body to sneak a camera ribbon cable out without damage?
If not, i think ill be modifying the case or redesigning a plastic alternative piece. Would you all be interested in linking that in the wiki if i made it?
Hello,The camera ribbon cable out is not currently supported, but we will provide an acrylic front panel as a backup to improve the impact on the wifi signal. and you can modify the acrylic panel to support the camera ribbon cable out. Thanks for your feedback.Best regards
Hello,「NAS」:Network Attached Storage; NASPI is a NUC-style NAS storage solution based on the latest Raspberry Pi 4. Geekworm has many other storage boards:x825,x829,x832,x857,x862,x873etc. You can get more information at the Geekworm store.
Enable comment auto-refresher
Anonymous user #30
Permalink |
Anonymous user #30
Permalink |
Anonymous user #29
Permalink |
Anonymous user #23
Permalink |
Anonymous user #28
Permalink |
Lisa
Anonymous user #27
Permalink |
Lisa
Anonymous user #26
Permalink |
Lisa
Anonymous user #25
Permalink |
Anonymous user #24
Permalink |
Anonymous user #24
Anonymous user #24
Lisa
Anonymous user #23
Permalink |
Lisa
Anonymous user #22
Permalink |
Lisa
Anonymous user #21
Permalink |
Lisa
Anonymous user #21
Anonymous user #20
Permalink |
Lisa
Anonymous user #19
Permalink |
Lisa
Anonymous user #18
Permalink |
Lisa
Anonymous user #16
Permalink |
Lisa
Anonymous user #17
Anonymous user #15
Permalink |
Lisa
Anonymous user #14
Permalink |
Lisa
Anonymous user #13
Permalink |
Harry
Anonymous user #12
Permalink |
Anonymous user #12
Permalink |
Anonymous user #11
Permalink |
Lisa
Anonymous user #11
Anonymous user #10
Permalink |
Lisa
Anonymous user #9
Permalink |
Lisa
Anonymous user #8
Permalink |
Lisa
Anonymous user #7
Permalink |
Lisa
Anonymous user #6
Permalink |
Lisa
Harry
Anonymous user #5
Permalink |
Lisa
Harry
Anonymous user #4
Permalink |
Lisa
Anonymous user #3
Permalink |
Lisa
Anonymous user #2
Permalink |
Lisa
Anonymous user #1
Permalink |
Lisa