Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

12:26, 18 October 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,There is a learning process for the IC to read the power level, please try to fully charge and then discharge it a few times and it will remember the process. Please power Pi5 + X1012 poe hat via X1202 UPS.)
23:34, 17 October 2024 46.138.82.4 talk performed unknown action "comments/add" on X1202 ("Capacity: 8.34% (Medium), AC Power State: Unplugged, Voltage: 3.67V Battery level critical." But 3 green LEDs are on)
17:51, 17 October 2024 46.138.82.4 talk performed unknown action "comments/add" on X1202 ("Capacity: 65.42% (Full), AC Power State: Unplugged, Voltage: 3.90V UPS is unplugged or AC power loss detected." If I connect POE via x1012 to rpi5 with x1202, it seems like the adapter is not connected, but 4 green LEDs are on. Is it ok or something wrong?)
18:23, 3 October 2024 14.153.79.53 talk performed unknown action "comments/add" on X1202 (One more thing you need to consider is to think about the conversion rate of UPS HAT, which is usually around 85%.)
03:01, 1 October 2024 86.87.123.160 talk performed unknown action "comments/add" on X1202 (Hello, I have 4 batteries, each with a capacity of 2980mAh. The total capacity is therefore 4x2980mAh=11920mAh. With the Raspberry running my application I measured it draws 700mA. So 11920mAh / 700mA = approx 17 hours of running time. Can someone confirm this? Thanks in advance.)
22:44, 30 September 2024 185.50.233.235 talk performed unknown action "comments/add" on X1202 (Actually I see it in the interface picture, point 6: 5VO power output LED: if the Pi 5 is not detected, will turn on for 3 second then off. Does it mean then that the output USB gives continuous power for 3 seconds after the RPI shuts down? Is the powering of the USB output seamless till switch off?)
22:32, 30 September 2024 185.50.233.235 talk performed unknown action "comments/add" on X1202 (Hi! Could I use the USB output to power up a USB hub? In the interface picture it says: 5V, current unlimited, but down in the user manual it says: USB2.0 type-A power output socket, which implies 5V 500mA, which would be not enough I guess. The use case is that the RPI cuts the power on its usb 3.0 ports at shutdown too soon, causing an increase of the Unexpected Power Loss SMART counter. Using an active USB hub between the RPI and the USB SSD enclosure solves the problem, but at power los...)
01:13, 26 September 2024 109.227.146.157 talk performed unknown action "comments/add" on X1202 (Me the same. I think the board can not manage PD with those smart power supplies)
18:13, 25 September 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,please refer to X1202_Hardware#Raspberry Pi GPIO used--GPIO16 Control battery charging, High-charging disabled, Low-charging enabled)
18:10, 25 September 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,yes,you can use the X1012 NVMe+POE shield with X1202 UPS baord.)
17:59, 25 September 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (No. If your problem is not solved, please tell us more details by email <info@geekworm.com>.thanks)
21:37, 24 September 2024 98.169.66.79 talk performed unknown action "comments/add" on X1202 (Hello, is it possible to reduce the charging current down to 1A? I would like reduce the current “fast charging rate” to prolong the life of the batteries.)
08:08, 22 September 2024 46.138.90.187 talk performed unknown action "comments/add" on X1202 (Can I use PoE Hat with x1202?)
19:16, 16 September 2024 131.227.23.23 talk performed unknown action "comments/add" on X1202 (Hi Lisa, I checked both options. Can x-rays affect it (I've flown with them)?)
17:55, 16 September 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi, X1202 must be used with Pi5. Please install pi5 and test it.)
05:06, 15 September 2024 131.227.23.23 talk performed unknown action "comments/add" on X1202 (Hello everyone. I have two X1202 V1.1 with two different USB-C 5.1V/5.0A power supplies and one DC jack 12V/2A adapter. If I connect the X1202 without Raspberry Pi to the USB-C adapters, nothing happens. If I use the 12V adapter, everything works fine with any of the X1202. Why can't the X1202 see the USB-C adapters?)
15:42, 2 September 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi, It is recommended that you reserve LED holes and switch holes on the custom enclosure. I think this is easier to do.)
05:30, 1 September 2024 64.250.65.36 talk performed unknown action "comments/add" on X1202 (I have seen that it supports an external switch. I am wondering simply because the lights may be hidden in my custom enclosure.)
17:19, 31 August 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,Sorry, Could you please let us know why you want to do this? The X1202 already has LED indicators and power button, and supports external switche.)
12:14, 28 August 2024 64.250.65.36 talk performed unknown action "comments/add" on X1202 (I want to have my own power switch and led indicator for power with the x1202, is this possible?) Tags: Mobile edit Mobile web edit
17:19, 22 August 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Key Features：Power Management：Automatic safe shutdown when battery voltage is low (programmable); please refer to: [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1202 Software] 4.2 Change the battery low voltage to implement safe shutdown. default is less than 3.20Vdc.)
17:19, 22 August 2024 Lisa talk contribs performed unknown action "comments/delete" on X1202
17:18, 22 August 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Key Features：Power Management：Automatic safe shutdown when battery voltage is low (programmable); please refer to: [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1202 Software] 4.2 Change the battery low voltage to implement safe shutdown. default is less than 3.20Vdc.)
23:13, 20 August 2024 182.52.185.30 talk performed unknown action "comments/add" on X1202 (Thanks, one more question. Does this unit has undervoltage protection (and which voltage)? I don't see this detail on product page.)
17:38, 20 August 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hello,LED light off does not mean shutdown.please refer to X1202 Hardware#Battery voltage level indicators)
22:35, 19 August 2024 180.180.198.99 talk performed unknown action "comments/add" on X1202 (What is the lowest voltage power cutoff? I saw all 4 battery leds off but raspberry pi is still running.)
19:10, 15 August 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,There is a learning process for the IC to read the power level, please try to fully charge and then discharge it a few times and it will remember the process.)
07:24, 12 August 2024 121.225.189.42 talk performed unknown action "comments/add" on X1202 (After that, I turned off the power input of the charger and continued to read the feedback value of the battery gauge. It is slowly increasing, even though I have disconnected the charger. It will reach around 80% battery level in about 30 minutes.)
07:22, 12 August 2024 121.225.189.42 talk performed unknown action "comments/add" on X1202 (Hello, I am using the x1202 model of UPS, and I have encountered a phenomenon. When the battery is low, I charge the UPS and shut down the Raspberry Pi. After the charging current drops to 0, I turn on the Raspberry Pi to check the battery level, but it shows only 1%. However, the battery voltage has already reached 4.2V. It seems that there is an error in the battery gauge.)
18:26, 23 July 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hello,please refer to X1202 HardwareGPIO16 function.and you need to write a script to do this yourself.)
22:58, 22 July 2024 192.77.184.26 talk performed unknown action "comments/add" on X1202 (Can the full charge voltage be adjusted via script or configuration code? It isn't good for LiIon batteries to sit fully charged for extended periods. Ideally they would charge to ~3.9-4V while retaining the option of charging to 4.2V Can you set PSU_MAX_CURRENT=3000 instead of 5000 to draw less Amps from power supply while charging? Could you set it to 2000?)
18:23, 17 July 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Yes. You can do this via script, just implement a timer in the script. You can also refer to other users' feedback X1200#comment-4845, Hope it helps you.)
18:43, 16 July 2024 176.200.80.175 talk performed unknown action "comments/add" on X1202 (Yes, we know that it can be turned off with the external switch but since the Raspberry Pi is installed in an inconvenient position and is used as a dash in the car that connects to the ECU to display its data, we would like it to turn off on its own after a certain time that the power was turned off. Since X1202 communicates when there is no more power, on this event you could start a countdown, close open applications and turn off the system, without using a keyboard, mouse and external swi...)
16:06, 15 July 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi，On-board push button performs the same actions as the Pi's power button. Turn off X1202 and pi5 at the same time by using an external switch)
20:47, 13 July 2024 185.21.248.71 talk performed unknown action "comments/add" on X1202 (hi, how can I close all applications and turn off the Raspberry pi after 5 minutes after the external power supply has been turned off?? I don't want to drain the batteries to make it shut down)
12:25, 8 July 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hello，X1202 only supports 18650 Flat Top batteries,please refer to X1202#FAQ---[Q: What battery is recommended for this ups shield].)
12:24, 8 July 2024 Lisa talk contribs performed unknown action "comments/delete" on X1202
12:20, 8 July 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hello，X1202 only supports 18650 Flat Top batteries,please refer to FAQ---[Q: What battery is recommended for this ups shield].)
12:45, 7 July 2024 124.122.125.98 talk performed unknown action "comments/add" on X1202 (You say to not use batteries with built in protection circuit, but I want to use LiFePo4 cells. Can I use these well known cells? For safety I only use this type. What is the problem?)
11:24, 2 July 2024 Harry talk contribs performed unknown action "comments/add" on X1202 (Hello Refer to X1202#FAQ Q1)
08:50, 2 July 2024 98.13.9.168 talk performed unknown action "comments/add" on X1202 (I'm getting the same thing... my screen works but my keyboard doesn't light up)
11:18, 27 June 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hi,X1202 UPS not compatible with X708-A1 Battery Holder.)
09:28, 27 June 2024 175.116.49.141 talk performed unknown action "comments/add" on X1202 (Can this be used with the X708-A1 board?)
14:49, 24 June 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (You can consider the X-UPS1 with 12V output)
14:38, 24 June 2024 Lisa talk contribs performed unknown action "comments/add" on X1202 (Hello,X1202 does not support X1009. X1009 requires DC12V power in, X1202 UPS only provides 5V output,)
07:16, 22 June 2024 185.211.32.105 talk performed unknown action "comments/add" on X1202 (Can this power 5, 3.5" drives on the x1009, through the board? can the x1009 power through the second barrel for the HD power? or would i use an ATX for the drives and leave the boards powered through the ups?)
03:54, 7 June 2024 23.93.48.84 talk performed unknown action "comments/add" on X1202 (I get warning in Ubuntu 24.04 on start: Raspberry pi PMIC Monitor: "This power supply is not capable of supplying 5A; power to peripherals..." screen seems to work...)
18:35, 31 May 2024 Harry talk contribs performed unknown action "comments/add" on X1202 (Hello, x1202 can meet your need. Refer to File:X1202-commnt1.png)
18:28, 31 May 2024 Harry talk contribs performed unknown action "comments/add" on X1202 (Sorry, No 3D file, only dxf file.)
18:28, 31 May 2024 Harry talk contribs performed unknown action "comments/delete" on X1202