Main public logs

Combined display of all available logs of Geekworm Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

16:16, 21 April 2022 189.217.0.185 talk performed unknown action "comments/add" on X728 (Hi, both button top and flat top batteries woudl fit right?)
10:25, 20 April 2022 114.167.187.215 talk performed unknown action "comments/add" on X728 (Is it a specification that the UPS does not power down after the RPI shuts down successfully using the X728? Due to this phenomenon, RPI does not start even if power is supplied to the UPS after shutdown. The AON pin is set to short.)
10:46, 23 March 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi， Yes，you can use [5v IN XH2.54], but please note ：DO NOT connect 5V to the BATT connector, this is very dangerous.)
15:56, 19 March 2022 1.157.113.202 talk performed unknown action "comments/add" on X728 (OP here, the reason I am asking is that I tried to supply power to this hat through the port from a LM2968 buck convertor but the converter belw up. If I can't supply power in to the 5v XH2.54 connector, I will have to wire it in to the barrel jack (or maybe using dupont connectors straight on to the GPIO pins??????))
11:52, 19 March 2022 1.157.113.202 talk performed unknown action "comments/add" on X728 (On the underside of the X728 is a 5v in port (just under the barrel jack). Can this be used to supply power to the hat, or can I only use the barrel jack or USB C port?) Tags: Mobile edit Mobile web edit
18:28, 14 February 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello， Did you find the address [0x68] of the RTC with the command [sudo i2cdetect -y 1] ?)
11:44, 13 February 2022 23.127.128.93 talk performed unknown action "comments/add" on X728 (Hello - I am running Raspberry Pi OS Bullseye (January 2022 release). I followed the documentation as well as I could understand it. I ran 'sudo raspi-config' and enabled the I2C interface, then rebooted the Raspberry Pi with the X728 v2.1 installed. When I run dmesg, I see the following message displayed: i2c i2c-1: new_device: Instantiated device ds1307 at 0x68 i2c i2c-1: Failed to register i2c client ds1307 at 0x68 (-16) Is this something I should be concerned about? Also - I cloned t...)
10:04, 11 February 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello， beacuse X728 has overcurrent protection and overvoltage protection Automatic safe shutdown when battery low (voltage <3.0V) Ultra-low standby power consumption to maximize battery life)
04:46, 11 February 2022 89.64.87.242 talk performed unknown action "comments/add" on X728 (Oh It's me again! Just got above 3V and the current is now higher! I understand that if the voltage is extremely low then it charges very slowly in order not to destroy the cells. When voltage is above 3V it charges normally. Am I right?)
04:44, 11 February 2022 89.64.87.242 talk performed unknown action "comments/add" on X728 (Hello geekworm! I've been findin X728v2.1 an excellent product! Very usefull and great quality for the price. I forgot to turn off RPi on standby mode and it drained my cells down to 2,97V. The Cell is Samsung INR18650-35E which has a 2.65V of cut-off voltage and therefore you rescued my cells! But when I plugged DC-Jack with 5,01V to X728 it draws only 0,15A current. So It's charging very slow or not at all. One of four battery diodes is blinking.)
22:57, 10 February 2022 23.252.83.122 talk performed unknown action "comments/add" on X728 (I ripped off the buzzer. Couldn't take it anymore. Everything else works as it should for my testing purposes.)
09:39, 10 February 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi, could you please send us some test videos？and tell us your order number,please send to <support@geekworm.com>；thanks~)
00:06, 10 February 2022 23.252.83.122 talk performed unknown action "comments/add" on X728 (Plug power in and it still buzzes. Installed the python scripts from github. They work fine and says AC power is connected. I even wrote my own python script to turn pin 20 to 0 and IT STILL IS BUZZING. Can I return this? Bought on amazon)
23:26, 9 February 2022 23.252.83.122 talk performed unknown action "comments/add" on X728 (I plug in power supply without anything plugged in. No pi or batteries. Blue light comes on. Press the power button and it beeps continuously. Add batteries, still beeps. What do I do with pin 20 to get it to stop beeping?)
11:01, 9 February 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello, 1/ X728 V2.1 add a buzzer controlled by CPIO 20; please plug in the power supply to the X728 without raspberry pi , and turn it on to check if it is still calling; if not, please check GPIO 20 is occupied. Raspberry Pi Tutorial: How to Use a Buzzer: please refer to :X728-Software#FAQ)
08:10, 9 February 2022 23.252.83.122 talk performed unknown action "comments/add" on X728 (I just got my board today and put batteries in and USB c power and I can't get it to stop buzzing. Hold button to shutdown and restart and its still buzzes.)
15:21, 5 January 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello， It's 5V output, directly connected to the Raspberry Pi 40-pin header--pin 2,pin 4 ；output current is shared, and X728-A1 has no set limit.)
15:14, 5 January 2022 Lisa talk contribs performed unknown action "comments/delete" on X728
09:49, 5 January 2022 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，It depends on your power supply or batteries.)
16:46, 4 January 2022 112.204.162.170 talk performed unknown action "comments/add" on X728 (What's the power output of X728-A1's XH2.54 pins?)
10:52, 24 December 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Yes.)
02:17, 23 December 2021 192.55.54.50 talk performed unknown action "comments/add" on X728 (Does the X728 stop charging the batteries once they reach 100% charge?)
10:40, 7 December 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，please refer x728-hardware--(Pins and GPIO used);you can use pins that are not occupied by x728)
10:40, 7 December 2021 Lisa talk contribs performed unknown action "comments/delete" on X728
10:40, 7 December 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，please refer [x728-hardware]--(Pins and GPIO used);you can use pins that are not occupied by x728)
02:22, 7 December 2021 192.109.205.15 talk performed unknown action "comments/add" on X728 (I am designing my own daughter board that must work in conjunction with the X728 DC UPS. I need to use several GPIO pins, but want to make sure I don't cause a conflict between my the board I am designing and the X728 DC UPS. I know that you use I2C on pins 3 and 5, and I believe you also use GPIO5 and GPIO12. You use Pins 2,4 for power too. Are there any other GPIO pins used by the X728 DC UPS, or am I free to use all the rest of the GPIO port?)
05:52, 2 December 2021 192.173.161.216 talk performed unknown action "comments/add" on X728 (*WARNING* This hardware is not yet supported by BULLSEYE released 10/30/21. python packages needed to drive the software are not available at this time. Do not upgrade to BULLSEYE until you are certain all python packages are updated.)
15:20, 16 November 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，1/for the BEEPING: X728 V2.1 add a buzzer controlled by CPIO 20; please plug in the power supply to the X728 without raspberry pi , and turn it on to check if it is still calling; if not, please check GPIO 20 is occupied. 2/[AC fail led is blinking]: We need to troubleshoot whether it is a line problem. Could you send us a video to check it? <support@geekworm.com> and please tell us your order NO.)
21:16, 15 November 2021 51.6.181.168 talk performed unknown action "comments/add" on X728 (Hi, my AC fail led is blinking while my usbc is connected to the x782 V2.1. Any reason? Also another x782 V2.1. is just continuously beeping while the batteries are connected. Why is that?)
16:29, 6 September 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，Yes, you can use unoccupied Pins and GPIO)
09:53, 5 September 2021 71.38.165.199 talk performed unknown action "comments/add" on X728 (According to the "X728-hardware" on the wiki, pins 2, 3, 4, 5, 6, 29, 31, 32 and 33 are used by the X728. Are the remaining Pi pins available for us to use and does the connector on the X728 pass those through?)
14:46, 12 August 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，If the voltage across the capacitor is also 3.7V, then it is very likely that the chip is burned out（next to the upper right corner of the ups [2R2] ）. Please check it.)
01:08, 12 August 2021 82.6.0.80 talk performed unknown action "comments/add" on X728 (the mosfet blew so I replaced it but it only outputs 3.7v now. What could have caused this? i see no other damage on the board.)
12:14, 30 July 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi，DC Barrel positive tip（the tip inside the DC port is positive.）)
23:39, 29 July 2021 80.4.69.13 talk performed unknown action "comments/add" on X728 (Is the DC Barrel positive tip or negative tip?)
08:01, 28 July 2021 114.151.81.253 talk performed unknown action "comments/add" on X728 (Thank you. I understand.)
17:36, 27 July 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，Because the x728 battery holder has a built-in protection circuit.)
14:59, 27 July 2021 114.151.81.253 talk performed unknown action "comments/add" on X728 (I'm currently using an unprotected battery. Can you tell me why I shouldn't use a protected battery? I think it's safer.)
14:31, 27 July 2021 114.151.81.253 talk performed unknown action "comments/add" on X728 (Thanks, I wanted this for my X728.)
10:11, 27 July 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，You can find it here： https://geekworm.com/)
18:04, 26 July 2021 114.151.81.253 talk performed unknown action "comments/add" on X728 (Where can I get the switch with the four wires connected in the image?)
14:31, 26 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，There is no LED light on the X728-A2 battery holder； The green indicator of x728 will show the battery status.)
14:11, 26 June 2021 71.159.244.248 talk performed unknown action "comments/add" on X728 (My bad. I found the manual.)
14:07, 26 June 2021 71.159.244.248 talk performed unknown action "comments/add" on X728 (Does A2 battery holder shows power remaining?)
13:51, 26 June 2021 71.159.244.248 talk performed unknown action "comments/add" on X728 (I got X728 and X728-A2 (battery holder). I have Pi 4B. I can't figure it out on assembly. There were no instructions on assembly and not even steps to connect jumper. What the heck? How can I assemble this?)
15:14, 16 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello, Sorry for the late reply. please follow the steps to test if the X728 issue: a:Take the X728 off from the Raspberry Pi, remove all the batteries, power supply, and all jumper caps. Then connect the battery or power supply, press the blue power button on X728, the blue LED should be on, and then press and hold the power button for more than 8 seconds, the blue LED should be off.(These steps indicate that the X728 has no issue.) b:Please check and confirm if other device occupy the GPI...)
14:52, 16 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello, Sorry for the late reply. for the automatically shuts down： 1/Remove all jumper cap, 2/Remove all 18650 battery 3/Place 18650 battery again and wait a few seconds before testing. 4/Please check and confirm if other device occupy the GPIO with X728. I noticed your steps, please do not supply power through the USB-C port of the RPi. If your x728 is V1.2 version； Please check if enable the ASD function (shorted the ASD header), if you enable the ASD function, please make sure your opera...)
11:44, 16 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，no limit. If you want to use more batteries, we recommend X708-A1, which supports 18650 batteries/8pcs ；please refer here：https://wiki.geekworm.com/X708-A1#/media/File:X708-A1-05.jpg)
11:38, 16 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hello，We do not recommend this，and we have not tested like that. Please refer the software of X728 V1.3；regards)
19:44, 15 June 2021 Lisa talk contribs performed unknown action "comments/add" on X728 (Hi,please refer here:https://wiki.geekworm.com/X728#/media/File:X728-IMG-7976-%E8%B7%B3%E7%BA%BF%E8%AF%B4%E6%98%8E.jpg)