Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
17 September 2024
|
|
22:20 | (Comments log)[37.201.213.105; 43.246.209.55; 45.80.33.8 (2×)] | |||
|
|
22:20 37.201.213.105 talk posted a new comment on X306 (Since I cannot reply to your comment, I will reply to my own. You tell me if I am having a problem or a malfunction. Let me rephrase my question: Does the Geekworm X306 V1.3 support 5V output on the 4-pin header?) | ||||
|
|
16:36 45.80.33.8 talk posted a new comment on X885 (Hello Is it possible to monitor the RAID status other than by the color of the LEDs for example via snmp, email alert? Thanks) | ||||
|
|
16:35 45.80.33.8 talk posted a new comment on NASPi 3.5 (Hello Is it possible to monitor the RAID status other than by the color of the LEDs for example via snmp, email alert? Thanks) | ||||
|
|
00:02 43.246.209.55 talk posted a new comment on PiKVM (Which Model could support HDMI video passthrough ？How to make config in KVM-A3 to support hdmi passthrough？) | ||||
16 September 2024
|
|
19:59 | (Comments log)[86.141.76.93; 131.227.23.23] | |||
|
|
19:59 86.141.76.93 talk posted a new comment on X728 (for the benefit of other users, be ware xSoft.sh has been updated on 13/09/2024 to fix this - GPIO pins were not being reset properly) | ||||
|
|
19:16 131.227.23.23 talk posted a new comment on X1202 (Hi Lisa, I checked both options. Can x-rays affect it (I've flown with them)?) | ||||
15 September 2024
|
|
20:36 | (Comments log)[131.227.23.23; 185.50.233.235 (2×)] | |||
|
|
20:36 185.50.233.235 talk posted a new comment on X728-script (Only one more question: if the set is -> "CHG Ctrl" - Open : GPIO16 output stays high: Charging enabled, is it also a battery automatic charging, as if the jumper would be shorted? Or I have to set 0 after the batteries are fully recharged, otherwise it remains on constant charging?) | ||||
|
|
20:30 185.50.233.235 talk posted a new comment on X728-script (Hi! I experienced also some strange behavior. Shorting Chg En charges the batteries very fast to 100%, and then it goes down to 93% in couple of hours and then it will be recharged again and repeats. Very fast cycle, I think it kills the batteries very fast. If I don't short, the batteries go down from 100% to 95% in a night time, so it is also very fast. I assumed that if the board is powered, the batteries remain intact and keep capacity for months or so. What I found out is that the GPIO...) | ||||
|
|
05:06 131.227.23.23 talk posted a new comment on X1202 (Hello everyone. I have two X1202 V1.1 with two different USB-C 5.1V/5.0A power supplies and one DC jack 12V/2A adapter. If I connect the X1202 without Raspberry Pi to the USB-C adapters, nothing happens. If I use the 12V adapter, everything works fine with any of the X1202. Why can't the X1202 see the USB-C adapters?) | ||||
14 September 2024
|
|
06:25 | (Comments log)[97.99.215.98; 37.201.213.105; 151.59.132.229] | |||
|
|
06:25 97.99.215.98 talk posted a new comment on P252 (Using P252 for a portable Pi 3B project. Great design! Long term think about optional dust plugs for unused ports (RJ-45, USB, audio, HDMI). Port for microSD can be covered with quality adhesive rubber or electrical tape.) | ||||
|
|
02:36 37.201.213.105 talk posted a new comment on X306 (Geekworm X306 V1.3 appears to output only 3.7V on the 4-pin header. Why is that?) | ||||
|
|
00:01 151.59.132.229 talk posted a new comment on XScript (update: if i try to give this command i get this response and the rasp does not turn off: rasp@rasp4:~/xscript $ xSoft.sh 0 27 Your device will be shutting down in 2 seconds... gpioset: at least one GPIO line offset to value mapping must be specified gpioset: at least one GPIO line offset to value mapping must be specified) | ||||
13 September 2024
| 23:35 | Comments log 151.59.132.229 talk posted a new comment on XScript (hi I just installed naspi v.2, raspberry pi 4b, raspberry pi os bookworm. I tried to install the script by following this tutorial, all good until this part “sudo ./install-sss.sh” where it tells me it can't find the script, checking in the github repository in fact there is nothing with that name and I get the error “sudo: ./install-sss.sh: command not found”. i proceeded anyway using “echo ‘alias xoff=’sudo /usr/local/bin/xSoft.sh 0 27'” >> ~/.bashrc source ~/.bashrc” then when I give t...) | ||||