Recent changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
16 September 2024
19:16 | Comments log 131.227.23.23 talk posted a new comment on X1202 (Hi Lisa, I checked both options. Can x-rays affect it (I've flown with them)?) |
15 September 2024
|
20:36 | (Comments log)[131.227.23.23; 185.50.233.235 (2×)] | |||
|
20:36 185.50.233.235 talk posted a new comment on X728-script (Only one more question: if the set is -> "CHG Ctrl" - Open : GPIO16 output stays high: Charging enabled, is it also a battery automatic charging, as if the jumper would be shorted? Or I have to set 0 after the batteries are fully recharged, otherwise it remains on constant charging?) | ||||
|
20:30 185.50.233.235 talk posted a new comment on X728-script (Hi! I experienced also some strange behavior. Shorting Chg En charges the batteries very fast to 100%, and then it goes down to 93% in couple of hours and then it will be recharged again and repeats. Very fast cycle, I think it kills the batteries very fast. If I don't short, the batteries go down from 100% to 95% in a night time, so it is also very fast. I assumed that if the board is powered, the batteries remain intact and keep capacity for months or so. What I found out is that the GPIO...) | ||||
|
05:06 131.227.23.23 talk posted a new comment on X1202 (Hello everyone. I have two X1202 V1.1 with two different USB-C 5.1V/5.0A power supplies and one DC jack 12V/2A adapter. If I connect the X1202 without Raspberry Pi to the USB-C adapters, nothing happens. If I use the 12V adapter, everything works fine with any of the X1202. Why can't the X1202 see the USB-C adapters?) |
14 September 2024
|
06:25 | (Comments log)[97.99.215.98; 37.201.213.105; 151.59.132.229] | |||
|
06:25 97.99.215.98 talk posted a new comment on P252 (Using P252 for a portable Pi 3B project. Great design! Long term think about optional dust plugs for unused ports (RJ-45, USB, audio, HDMI). Port for microSD can be covered with quality adhesive rubber or electrical tape.) | ||||
|
02:36 37.201.213.105 talk posted a new comment on X306 (Geekworm X306 V1.3 appears to output only 3.7V on the 4-pin header. Why is that?) | ||||
|
00:01 151.59.132.229 talk posted a new comment on XScript (update: if i try to give this command i get this response and the rasp does not turn off: rasp@rasp4:~/xscript $ xSoft.sh 0 27 Your device will be shutting down in 2 seconds... gpioset: at least one GPIO line offset to value mapping must be specified gpioset: at least one GPIO line offset to value mapping must be specified) |
13 September 2024
23:35 | Comments log 151.59.132.229 talk posted a new comment on XScript (hi I just installed naspi v.2, raspberry pi 4b, raspberry pi os bookworm. I tried to install the script by following this tutorial, all good until this part “sudo ./install-sss.sh” where it tells me it can't find the script, checking in the github repository in fact there is nothing with that name and I get the error “sudo: ./install-sss.sh: command not found”. i proceeded anyway using “echo ‘alias xoff=’sudo /usr/local/bin/xSoft.sh 0 27'” >> ~/.bashrc source ~/.bashrc” then when I give t...) |
11 September 2024
06:43 | Comments log 185.50.233.235 talk posted a new comment on X728-script (I have the chg en open, assumingly not charging, working normally with 5V power adapter, still the battery capacity drops rapidly, 1-2 %point per day. Is this normal? What drains the battery so fast?) |
10 September 2024
|
22:49 | (Comments log)[71.187.173.188 (2×)] | |||
|
22:49 71.187.173.188 talk posted a new comment on LVDS2 (What about 800x480 single channel LVDS ? I need to capture signal to HDMI (instead LCD LQ070T5GC01) Will it work?) | ||||
|
22:45 71.187.173.188 talk posted a new comment on LVDS2 (What about 800x480 single channel LVDS ? I need to get signal from LCD LQ070T5GC01 Will it work?) |