Difference between revisions of "T208-Software"
(9 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
{{GD Template Impl}} | {{GD Template Impl}} | ||
− | 1. Update software source on Ubuntu | + | We test the following step base the Jetson nano image (ubuntu 18.04 LTS) |
+ | |||
+ | 1. Update software source on Ubuntu, refer to [[Update software source on Ubuntu]] | ||
+ | |||
+ | '''NOTE''': You must connect the internet via Ethernet or [[Wireless USB adapter]] before software update. | ||
2. To install pip for Python 3 on Ubuntu, run the following commands as root or sudo user in your terminal: | 2. To install pip for Python 3 on Ubuntu, run the following commands as root or sudo user in your terminal: | ||
Line 10: | Line 14: | ||
sudo apt-get install libi2c-dev i2c-tools | sudo apt-get install libi2c-dev i2c-tools | ||
pip install smbus | pip install smbus | ||
− | 5. To check what i2c devices connected | + | 5. To check what i2c devices connected (This is very important!!) |
− | sudo i2cdetect -y -r 1 | + | sudo i2cdetect -y -r 1 |
+ | PS: The i2c address ix 0x3C | ||
+ | |||
6. To install Nano editor on Ubuntu | 6. To install Nano editor on Ubuntu | ||
sudo apt-get install nano | sudo apt-get install nano | ||
− | 7. | + | 7. Download the sample python file ([[File:Bat.py]]) for i2c battery voltage & percentage reading, then run the following command to test it. |
− | + | sudo python Bat.py | |
+ | 8. Download the sample python file ([[File:Pld.py]]) for AC power loss / power adapter failure detection, then run the following command to test it. | ||
+ | sudo python Pld.py | ||
+ | Note: you can get the sample python file from github also; | ||
+ | git clone https://github.com/geekworm-com/T208 | ||
+ | '''FAQ''' | ||
+ | |||
+ | A: Found some error | ||
+ | |||
+ | Q: | ||
+ | 1. check your python version with command 'sudo python -v' | ||
+ | |||
+ | 2. check the I2C if is enable with command 'sudo i2cdetect -y -r 1', you can found the result is 0x36 | ||
+ | |||
+ | 3. Configure the appropriate software source, or you can't update. | ||
Return to [[T208]] | Return to [[T208]] | ||
+ | |||
+ | |||
<!--Add review function! --> | <!--Add review function! --> | ||
<comments /> | <comments /> |
Latest revision as of 16:48, 2 August 2023
We test the following step base the Jetson nano image (ubuntu 18.04 LTS)
1. Update software source on Ubuntu, refer to Update software source on Ubuntu
NOTE: You must connect the internet via Ethernet or Wireless USB adapter before software update.
2. To install pip for Python 3 on Ubuntu, run the following commands as root or sudo user in your terminal:
sudo apt-get update sudo apt-get install python-pip
3. To install Jetson GPIO library:
sudo pip install Jetson.GPIO
4. To install I2C dev library
sudo apt-get install libi2c-dev i2c-tools pip install smbus
5. To check what i2c devices connected (This is very important!!)
sudo i2cdetect -y -r 1
PS: The i2c address ix 0x3C
6. To install Nano editor on Ubuntu
sudo apt-get install nano
7. Download the sample python file (File:Bat.py) for i2c battery voltage & percentage reading, then run the following command to test it.
sudo python Bat.py
8. Download the sample python file (File:Pld.py) for AC power loss / power adapter failure detection, then run the following command to test it.
sudo python Pld.py
Note: you can get the sample python file from github also;
git clone https://github.com/geekworm-com/T208
FAQ
A: Found some error
Q: 1. check your python version with command 'sudo python -v'
2. check the I2C if is enable with command 'sudo i2cdetect -y -r 1', you can found the result is 0x36
3. Configure the appropriate software source, or you can't update.
Return to T208
Enable comment auto-refresher
Anonymous user #2
Permalink |
Lisa
Anonymous user #1
Permalink |
Lisa