Difference between revisions of "Template:PCIe to NVME Sets"
Jump to navigation
Jump to search
| Line 3: | Line 3: | ||
After the release of the [https://www.raspberrypi.com/products/ai-kit/ Raspberry Pi AI Kit], we tested four PIPs: [[X1001]], [[X1004]], [[X1011]], and [[M901]]. X1001, X1004, and M901 all support the hailo-8 ai accelerator, but X1011 does not. | After the release of the [https://www.raspberrypi.com/products/ai-kit/ Raspberry Pi AI Kit], we tested four PIPs: [[X1001]], [[X1004]], [[X1011]], and [[M901]]. X1001, X1004, and M901 all support the hailo-8 ai accelerator, but X1011 does not. | ||
| − | It should be noted that [[X1004]] uses [https://www.asmedia.com.tw/product/213yQcasx8gNAzS4/b7FyQBCxz2URbzg0 ASMedia ASM1182e] PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch | + | It should be noted that [[X1004]] uses [https://www.asmedia.com.tw/product/213yQcasx8gNAzS4/b7FyQBCxz2URbzg0 ASMedia ASM1182e] PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch, and speed is still PCIe Gen 2.0 5Gbps speed. when you use an hailo-8 ai accelerator, Raspberry Pi Fundation highly recommends using PCIe 3.0 to achieve best performance with your AI Kit. |
| − | |||
| − | |||
Finally, our conclusion is: | Finally, our conclusion is: | ||
Revision as of 11:36, 18 June 2024
Geekworm PCIe to NVME Sets:
After the release of the Raspberry Pi AI Kit, we tested four PIPs: X1001, X1004, X1011, and M901. X1001, X1004, and M901 all support the hailo-8 ai accelerator, but X1011 does not.
It should be noted that X1004 uses ASMedia ASM1182e PCIe switch, it can't support PCIe Gen 3 speed, so even though we forced to enable PCIe Gen 3.0 setting in Raspberry Pi 5, it is limited by ASMedia ASM1182e PCIe switch, and speed is still PCIe Gen 2.0 5Gbps speed. when you use an hailo-8 ai accelerator, Raspberry Pi Fundation highly recommends using PCIe 3.0 to achieve best performance with your AI Kit.
Finally, our conclusion is:
- If you need to use hailo-8 ai accelerator with high performance, it is recommended to use the official M.2 HAT+/X1015/X1002/X1003/M901 etc. When choosing these PIP boards, you should focus on whether there is a conflict between the camera cable and the PIP board installation, and enable PCIe3.0 to use hailo-8 ai accelerator. At the same time, you need to prepare an SD card as the system disk.
- If you don't care about the high performance brought by PCIe 3.0, then you can consider using X1004, so that you can use any socket of X1004 to install NVME SSD as the system disk, and another socket to install hailo-8 ai accelerator, so as to have both.
| Model | Compatible with | Position | NVMe M2 SSD Support | Matching Case | Support NVMe Boot | Other |
|---|---|---|---|---|---|---|
| X1000 | Raspberry Pi 5 | Top | 2230/2242 NVMe M2 SSD | P579 | Yes | |
| X1001 | Raspberry Pi 5 | Top | 2230/2242/2260/2280 NVMe M2 SSD | P579 | Yes | |
| X1002 | Raspberry Pi 5 | Bottom | 2230/2242/2260/2280 NVMe M2 SSD | P580 | Yes | |
| X1003 | Raspberry Pi 5 | Top | 2230/2242 NVMe M2 SSD | P579 / P425 / Official Case | Yes | only can be used with Raspberry Pi 5 Official Active Cooler or H501 |
| X1004 | Raspberry Pi 5 | Top | Dual 2280 NVMe M2 SSD | P579-V2 | supports NVMe boot with eeprom 2024/05/17 and later version | |
| X1011 | Raspberry Pi 5 | Bottom | 4PCS 2230/2242/2260/2280 NVMe M2 SSD | X1011-C1 | supports NVMe boot with eeprom 2024/05/17 and later version | |
| M901 | Raspberry Pi 5 | Top | 2230/2242/2260/2280 NVMe M2 SSD | P579 | Yes | |
| Q100 | Raspberry Pi 5 | Top | 2242 NVMe M2 SSD | P579 | Yes | With 1.3" 240x240 Color TFT |
| Q200 | Raspberry Pi 5 | Top | Dual 2280 NVMe M2 SSD | P579 | NO | |
| M300 | Raspberry Pi 5 | Top | 2230/2242 NVMe M2 SSD | P579 | Yes | |
| M400 | Raspberry Pi 5 | Top | 2230/2242/2280 NVMe M2 SSD | P579 | Yes |