Related changes
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
20 May 2024
|
|
03:52 | (Comments log)[73.16.134.38 (2×)] | |||
|
|
03:52 73.16.134.38 talk posted a new comment on X728 (OK, sorry, I figured it out. I was trying to follow the schematic from the 4-pin LED momentary push button, but everything works as expected if you follow what the Wiki suggests. The LED button has four pins: S1, S2, LED+, LED- The x728 has four pins: PWR, GND, GND, LED+ Connect them as such: PWR - S1 GND - S2 GND - LED- LED+ - LED+ I don't know why my incorrect wiring ever worked, but this is what it always should have been. Leaving this here in case anyone else has the same problem!) | ||||
|
|
01:25 73.16.134.38 talk posted a new comment on X728 (Small update: I compared the status of all GPIO pins with and without the button pressed, and none change (including 5, 13, and 26).) | ||||
19 May 2024
| 23:46 | Comments log 73.16.134.38 talk posted a new comment on X728 (Hello, apologies for the dumb question: my external power button correctly turns the board on, and "x728off" works, but the external power button stopped working to turn the board off recently. I think I may have accidentally deleted a script or service. However, I cannot figure it out. I am using V1.3. I tried following your software tutorial, but it only seems to make "x728off" work. If you can tell me how the 4-pin external power button works, I can write a script to make it work for me a...) | ||||
18 May 2024
| 02:06 | Comments log 145.224.103.153 talk posted a new comment on X703 (Is there a way to have a step file or a 2d file with dimension so we can draw our own case?) | ||||
15 May 2024
| 04:38 | Comments log 172.59.122.138 talk posted a new comment on How to enable OLED display (you say: Hi, you can ignore python-smbus package I ask: How Instructions do not work at all. Many failures.) | ||||
13 May 2024
| 16:21 | Comments log 104.28.42.26 talk posted a new comment on XScript (I have the same problem...) | ||||
9 May 2024
| 15:59 | Comments log 95.73.54.49 talk posted a new comment on How to Configure RAID Setting (Hi, How can I check health of the each disk in hardware RAID mode?) | ||||
7 May 2024
|
|
21:47 | (Comments log)[1.64.154.121 (3×)] | |||
|
|
21:47 1.64.154.121 talk posted a new comment on XScript (I also using raspberryOS 64bit(bookworm)) | ||||
|
|
21:45 1.64.154.121 talk posted a new comment on XScript (Hi, I followed this guide and now xoff works, but the fan not move at all. It show active and enabled when I enter "sudo systemctl status x-c1-fan.service". Is it the fan broken or have any suggestion to debug?) | ||||
|
|
02:17 1.64.154.121 talk posted a new comment on XScript (Hi, is there a version of Debian 12(Bookworm)? I'm using NASPi and the fan not working and "xoff: command not found" after install script.) | ||||
3 May 2024
| 05:21 | Comments log 93.104.122.139 talk posted a new comment on NASPi Gemini 2.5 (Is there possibility to use "wake ON lan" with it?) | ||||
2 May 2024
| 07:10 | Comments log 75.37.71.93 talk posted a new comment on NASPi Gemini 2.5 (I am once again asking how to get in contact WITH ANY SUPPORT PERSON WHATSOEVER IN REGARDS TO A FAULTY X882-A1 CONNECTOR. POTENTIAL BUYERS be aware this is what they are putting their customers through. I have tried other means of communication only to be ignored.) | ||||
1 May 2024
| 05:53 | Comments log 75.37.71.93 talk posted a new comment on NASPi Gemini 2.5 (What does it take to get a reply from Cindy, the (terrible) customer support person I got in regards to a garbage X882-A1 connector that came with this kit.) | ||||
30 April 2024
| 07:17 | Comments log 82.58.137.153 talk posted a new comment on XScript (Hi, I followed this guide and now xoff works like a charm, many thanks. On the other hand, even if I am able to run and control my fan, even at low speeds it's very loud. I tried changing some values in the x-c1-fan.sh script and the fan responded but it never got "silent" like it used to be. I remember it being very silent, especially at low speeds. What can i do? is there something i missed to try? I'm kinda a newbie when it comes to hardware, and the Naspi was not touched since i built i...) | ||||