Related changes
Jump to navigation
Jump to search
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
31 October 2024
|
|
14:27 | (Comments log)[46.138.178.175; 128.62.103.172] | |||
|
|
14:27 46.138.178.175 talk posted a new comment on X1201 (non of the scripts in x120x working raspberrypi:~/x120x $ sudo python3 merged.py Traceback (most recent call last): File "/home/user/x120x/merged.py", line 5, in <module> import smbus ModuleNotFoundError: No module named 'smbus') | ||||
|
|
05:20 128.62.103.172 talk posted a new comment on X1202 (It appears there may have been a firmware update? The device now appears on 0x48 and the voltages are different. Your software on github no longer works with the device.) | ||||
30 October 2024
| 14:44 | Comments log 151.251.158.107 talk posted a new comment on X1005 (Hello, I have a problem with overheating of the ssds [1]. Most of the time they are really hot. Temperature goes up to 85 degrees even if no data transfer is done. Sometimes ssds unmount and are not detected after they overheat. Is there any config or update that I could do to address this? I'll add cooler, but it is still not ok to reach such temperatures in idle. [1] 2 x Samsung 990 EVO 2TB (with latest firmware according to Samsung Magician). Only mounted and formatted as ext4. X1005 boa...) | ||||
28 October 2024
| 03:35 | Comments log 70.90.216.102 talk posted a new comment on X-UPS1 (Does this UPS cut power automatically if voltage is lower than 3v??) | ||||
27 October 2024
| 00:26 | Comments log 27.116.208.36 talk posted a new comment on X1300 (Is there any reason this X1300 set cannot also be used with a rpi4 if I used a 22-pin 0.5 pitch to 15-pin 1.0 pitch FFC cable? I understand that the fewer CSI lanes means 1080p50 rather than 1080p60, but the X1300 and X630 use the same toshiba hdmi chip.) | ||||
26 October 2024
| 04:24 | Comments log 129.2.192.239 talk posted a new comment on X708-A1 (Hi, could you please provide the 2D technical drawing? I need the dimension and distance between each screw hole for CAD work. It takes way too much time to open and operate the provided dxf file. Thank you.) | ||||
24 October 2024
| 00:52 | Comments log 96.238.18.5 talk posted a new comment on X1202 (I am using rpi5. I am NOT powering the rpi directly, it is powered by the UPS. The UPS is connected to 12v outlet on the robot via barrel connector.) | ||||
23 October 2024
|
|
21:03 | (Comments log)[67.8.28.135; 174.169.89.179 (2×)] | |||
|
|
21:03 67.8.28.135 talk posted a new comment on X1003 (Thanks for the tip on what drive works. I just purchased one from Amazon.) Tags: Mobile web edit, Mobile edit | ||||
|
|
02:45 174.169.89.179 talk posted a new comment on X1202 (I have the rpi with usb connected to a robot using a 12v outlet on the robot. I need to make sure rpi always has power to operate. Are there specific configurations I need in order to have the rpi/USB ALWAYS connected to the 12v power outlet on the robot?) | ||||
|
|
00:36 174.169.89.179 talk posted a new comment on X1202 (Is there a way to monitor the charge level of the batteries?) | ||||
22 October 2024
|
|
21:07 | (Comments log)[129.2.192.220 (2×)] | |||
|
|
21:07 129.2.192.220 talk posted a new comment on X708-A1 (Thank you for the reply. But what I want to know is the width of the wires for the XH2.54 connector. Like AWG 20, or 22.) | ||||
|
|
02:25 129.2.192.220 talk posted a new comment on X708-A1 (Hi, what's the gauge number of the XH2.54 wire? Thank you.) | ||||
21 October 2024
| 08:20 | Comments log 202.238.201.130 talk posted a new comment on X1201 (What is the level of protection against overcharging? I want to use this x1201 UPS with headless control from a distance, but even in low power charge mode controlled via GPIO, the amount of power charged exceeds the amount consumed. As a result, I am concerned that the battery will always be over 100%. I apologize in advance as I am still a beginner.) | ||||
20 October 2024
| 15:04 | Comments log 94.31.91.145 talk posted a new comment on X1011 (test) | ||||
19 October 2024
|
|
06:35 | (Comments log)[85.233.54.182; 78.90.162.24 (2×)] | |||
|
|
06:35 85.233.54.182 talk posted a new comment on X1001 (Can confirm WD 1 TB SSD PC SN730 works, and boots fine) | ||||
|
|
04:49 78.90.162.24 talk posted a new comment on X1011 (Sorry but I can't find way editing my comment. It is Markdown formatted but it is looking ugly as comment section seems not interpret it well.) | ||||
|
|
04:46 78.90.162.24 talk posted a new comment on X1011 (In case someone battling making NAS with large NVMEs... I'm almost 100% sure that 1A@5V(5.00W) is not enough for powering them. Example below is from 4x(Shenzhen Longsys Electronics Co., Ltd. Lexar NM790 NVME SSD (DRAM-less) (rev 01)). ``` # smartctl -c /dev/nvme0 smartctl 7.4 2023-08-01 r5530 [aarch64-linux-6.11.0-1004-raspi] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Firmware Updates (0x14): 2 S...) | ||||
18 October 2024
| 23:54 | Comments log 128.2.149.23 talk posted a new comment on X-UPS1 (Does this UPS handles and protect against reverse current on its output port? If there is current coming back from the output port, will the board still be able to handle it?) | ||||