5,653
edits
Changes
Jump to navigation
Jump to search
X883
,{{GD Template Impl}}
[[File:X883-Packing-List.jpg|thumb|right|X883 Packing List]]
[[File:X883-Interface-Schematic.jpg|thumb|right|X883 Interface Schematic]]
[[File:X883-IMG-2492.jpg|thumb|right|X883]]
[[File:X883-with-pi-4.jpg|thumb|right|X883 with pi 4]]
[[File:X883-with-pi-4-X735.jpg|thumb|right|X883 with pi 4 & X735]]
[[File:X883-PCB.png|thumb|right|X883 PCB size]]
==Overview==
This is an ultra-compact raspberry pi 4 dual 2.5 inch sata hdd/ssd storage board X883, it allows two 2.5" HDD/SSD to working at the same time with your Raspberry Pi 4. The SuperSpeed USB 3.0 port delivers a blistering data transfer rate of up to 5Gbps, letting you transfer a large amount of data in seconds.
x883 will replace [[X829]]
Note:
* Raspberry pi, 2.5" SATA SSDs/HDDs, power adapter are all not included
* Due to installation restrictions, please pay attention to the thickness of 2.5" SSD/HDD
* As with all SSDs, new SSD/HDD must be formatted before use
* Older SSD drives with less efficient flash media may not perform as well as newer drives
[[File:X883-support-HDD.jpg|600px]]
==Features==
* Ultra-compact storage solution for Raspberry Pi 4 - Dual 2.5" SATA HDD/SSD Shield, '''supports UASP NOT trim'''
* Supports dual 2.5 SATA HDDs/SSDs working at the same time.
* The newly designed USB connector can transmit more reliably.
* Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controllers
* Quick file transfer with high-speed USB3.1 5Gb/s connectivity from a PC or a Mac
* Fully compatible with X735 for intelligent power management and cooling your Raspberry Pi
* Fully compatible with X765 for powering over Ethernet (POE, 5V 5A)
* Fully compatible with X728 for uninterruptible power supply (18650 UPS, 5.1V 6A, smart power mgmt)
==How to Power==
Since X883 can install two 2.5-inch hard drives, it needs a high-quality power supply to provide enough current. <span style="color:red">Please use high quality power adapter that with inner protection, the low quality PSU may damage the X883 board and not recognized the HDD/SSD.</span>
* Power supply: '''5Vdc''' +/-5% , ≥4A
* Ports & Connectors: DC jack - 5.5x2.1mm
* (Note: DC5525 Jack is compatible with DC5521, so you can also use the PSU with DC5525 Jack)
[[File:X883-How-to-Power.jpg|600px]]
==Packing List==
* 1 x X883 Shield (Support Dual 2.5 inch SATA HDD/SSD)
* 1 x Carrier Board X883-A1 (To mount raspberry pi on X883)
* 1 x USB 3-D Connector
* 1 x 2-Pin Power Connection Wire
* 6 x Spacer F/F M2.5 x 14mm
* 2 x Spacer M/F M2.5 x 14+5mm
* 12 x Screw M2.5 x5mm
* 4 x Screw M3 x 6mm
==User Manual==
* How to Run Raspberry Pi 4 or 3 Off an SSD or Flash Drive: [[Does the X825/X855 support USB boot]]
* Tutorial – How to Initialize, Partition and Format a Brand New SSD in Windows: [[File:Tutorial_Initalize_New_SSD.pdf]]
* [https://www.addictivetips.com/ubuntu-linux-tips/set-up-openmediavault-on-raspberry-pi-4/ How to set up OpenMediaVault on Raspberry Pi 4]
Some Tips
*[[Properly Mount USB Storage on Raspberry Pi]]
*[[Auto Mount an NTFS USB Drive on Raspberry Pi]]
* [https://github.com/raspberrypi/firmware/issues/1515 Difficulty booting from SSD drive]
* How to build a Raspberry Pi NAS: https://youtu.be/gyMpI8csWis
==PCB dimention==
Dimensions source file (DXF): [[File:X883-V1.2-DWG.dxf]] - You can view it with Autodesk Viewer online
==FAQ==
Q1: What to do if HDD/SSD is not recognized?
A: Please refer to [[How to View/Partition/Format/Mount HDD/SSD]]
<!--Add review function! -->
<comments />
[[Category:Product Manual]]
[[Category:Raspberry pi]]
[[File:X883-Packing-List.jpg|thumb|right|X883 Packing List]]
[[File:X883-Interface-Schematic.jpg|thumb|right|X883 Interface Schematic]]
[[File:X883-IMG-2492.jpg|thumb|right|X883]]
[[File:X883-with-pi-4.jpg|thumb|right|X883 with pi 4]]
[[File:X883-with-pi-4-X735.jpg|thumb|right|X883 with pi 4 & X735]]
[[File:X883-PCB.png|thumb|right|X883 PCB size]]
==Overview==
This is an ultra-compact raspberry pi 4 dual 2.5 inch sata hdd/ssd storage board X883, it allows two 2.5" HDD/SSD to working at the same time with your Raspberry Pi 4. The SuperSpeed USB 3.0 port delivers a blistering data transfer rate of up to 5Gbps, letting you transfer a large amount of data in seconds.
x883 will replace [[X829]]
Note:
* Raspberry pi, 2.5" SATA SSDs/HDDs, power adapter are all not included
* Due to installation restrictions, please pay attention to the thickness of 2.5" SSD/HDD
* As with all SSDs, new SSD/HDD must be formatted before use
* Older SSD drives with less efficient flash media may not perform as well as newer drives
[[File:X883-support-HDD.jpg|600px]]
==Features==
* Ultra-compact storage solution for Raspberry Pi 4 - Dual 2.5" SATA HDD/SSD Shield, '''supports UASP NOT trim'''
* Supports dual 2.5 SATA HDDs/SSDs working at the same time.
* The newly designed USB connector can transmit more reliably.
* Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controllers
* Quick file transfer with high-speed USB3.1 5Gb/s connectivity from a PC or a Mac
* Fully compatible with X735 for intelligent power management and cooling your Raspberry Pi
* Fully compatible with X765 for powering over Ethernet (POE, 5V 5A)
* Fully compatible with X728 for uninterruptible power supply (18650 UPS, 5.1V 6A, smart power mgmt)
==How to Power==
Since X883 can install two 2.5-inch hard drives, it needs a high-quality power supply to provide enough current. <span style="color:red">Please use high quality power adapter that with inner protection, the low quality PSU may damage the X883 board and not recognized the HDD/SSD.</span>
* Power supply: '''5Vdc''' +/-5% , ≥4A
* Ports & Connectors: DC jack - 5.5x2.1mm
* (Note: DC5525 Jack is compatible with DC5521, so you can also use the PSU with DC5525 Jack)
[[File:X883-How-to-Power.jpg|600px]]
==Packing List==
* 1 x X883 Shield (Support Dual 2.5 inch SATA HDD/SSD)
* 1 x Carrier Board X883-A1 (To mount raspberry pi on X883)
* 1 x USB 3-D Connector
* 1 x 2-Pin Power Connection Wire
* 6 x Spacer F/F M2.5 x 14mm
* 2 x Spacer M/F M2.5 x 14+5mm
* 12 x Screw M2.5 x5mm
* 4 x Screw M3 x 6mm
==User Manual==
* How to Run Raspberry Pi 4 or 3 Off an SSD or Flash Drive: [[Does the X825/X855 support USB boot]]
* Tutorial – How to Initialize, Partition and Format a Brand New SSD in Windows: [[File:Tutorial_Initalize_New_SSD.pdf]]
* [https://www.addictivetips.com/ubuntu-linux-tips/set-up-openmediavault-on-raspberry-pi-4/ How to set up OpenMediaVault on Raspberry Pi 4]
Some Tips
*[[Properly Mount USB Storage on Raspberry Pi]]
*[[Auto Mount an NTFS USB Drive on Raspberry Pi]]
* [https://github.com/raspberrypi/firmware/issues/1515 Difficulty booting from SSD drive]
* How to build a Raspberry Pi NAS: https://youtu.be/gyMpI8csWis
==PCB dimention==
Dimensions source file (DXF): [[File:X883-V1.2-DWG.dxf]] - You can view it with Autodesk Viewer online
==FAQ==
Q1: What to do if HDD/SSD is not recognized?
A: Please refer to [[How to View/Partition/Format/Mount HDD/SSD]]
<!--Add review function! -->
<comments />
[[Category:Product Manual]]
[[Category:Raspberry pi]]